Find an Insulation Installer you can trust in Kyle.

This depends on the amount of insulation already present in your property. However, adding insulation has been proven to improve the energy efficiency of your home and decrease your heating bills, this is more obvious in older properties or where single glazing is still in situ.

Insulating a cavity wall should not affect the damp proofing of the wall. All insulation approved for use in cavity walls has been tested to ensure that it does not allow damp to pass through the wall. Some walls which receive a lot of wind driven rain are unsuitable for cavity wall insulation.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

Cavity wall insulation is basically the process of installing an insulating material between the two layers of brick making up a cavity wall, either as a retrofit measure or at the time of building. Obviously this is not a choice if you have solid wall, but for those who do possess a cavity wall, it represents an opportunity you may not want to let slide as it is a worthwhile and affordable wall insulation option. Clearly, cavity wall insulation will make your home or property feel warmer, but it also does come with a range of other benefits which is why we’d recommend installing it. In this post, we’re going to look at a number of reasons why having a cavity wall insulation done is a good idea.

• It’s one of the cheapest energy saving measures that’s available. Not only is cavity wall insulation really effective, but it can also deliver great saving. In other words, it possesses a bigger payback compared to other options. When compared to other types of insulation, you can’t install cavity walls insulation by yourself, however it’s not so expensive to have it installed. The cost of the insulation will be determined by a number of factors such as your location, the company hired and more.
• It reduces your energy bills. Cavity wall insulation can save you about £100 to £200 on a yearly basis on heating bills. In other words, this is usually able to pay for itself in as little as two years.
• It reduces your carbon carbon footprint. If your home is heated with gas or electricity like several other homes, producing that energy involves burning fossil fuels which is known to be hazardous for the environment. If the heat generated is now allowed to escape through the walls, that means you’d have to use more to keep up your required temperature. Installation of cavity wall insulation in homes will enable a more efficient usage of the energy which will ultimately cut UK’s carbon usage.

The short and simple answer to this question is yes, loft insulation does cause condensation. Over the years, problems with condensation in loft spaces have become increasingly common. While this may not be harmful in anyway, when the condensation becomes excessive it can lead to more serious issues taking root in your loft like wet rot, dry rot as well as black spot mould. Generally, the best thing to do if you’re concerned about the condensation in your loft space and that it may rapidly become a bigger problem is to get in touch with a damp specialist as soon as possible.

Even though insulating your loft space comes with a wide array of benefits like making the top floor rooms warmer, it’s however comes at the cost of making your loft or room space cooler. Condensation in lofts take place primarily due to the humid air making its way through insulation or other gaps into the loft space and touching a cooler surface which in turn results in beads of moisture on the timbers, lintels as well as the underside of the roof. This is why its always a great idea make use of thermal insulation with a vapour barrier that’s installed on the warmer side of the insulating material.

Condensation in loft is caused by excess moisture in the air and lack of adequate air ventilation. Here are some top reasons that gives rise to this in the loft:

• Extra insulation has been installed in the loft leading to a restriction on the natural air circulation in the property.
• When the storage boxes or other items that has been stockpiled in the loft blocks the roof vents.
• The release of steam and moist air into the loft space by hot water tanks.

With cavity walls being very similar to other type of brick works, it can be quite confusing to figure out the type of wall your property possesses. If your house was constructed after the 1920s, then its highly likely the you have cavity walls, while older houses (houses before the 1920s) are likely to have solid walls. What’s more? If you happen to own a home that was built in the last decade, then it’s very possible that it was built with insulation installed during construction.

An effective way to determine whether or not your property is built with cavity wall is to examine the brickwork on your home’s exterior. The bricks will typically possess a regular pattern if it features cavity walls. In the event whereby the brick work is covered by render, you can also figure it out by taking a measurement of the wall’s width. If the brick wall is beyond 3000mm in thickness ( from the exterior wall to the interior wall), then it probably features a cavity. Meanwhile, a wall that’s narrower is very likely to be solid. Stone walls, on the other hand, may actually be thicker but are most times solid.

In a situation whereby your house is built using steel frame or timber frame, or made using pre-fabricated concrete, there are varying rules that applies when it comes to insulation and should be examined by an expert before any insulation is installed. More often than not, most contractors will have installed special air vents, which can also be a good indicator that a cavity wall insulation has been done.

Before the commencement of any project, it’s always best to get an estimation of the cost. However, determining the cost of an external solid wall insulation is not the easiest of tasks as it relies on varying components such as the insulation materials to be used, labour cost and installation as well as the type of decorative finish to be incorporated. And depending on your choice of insulation material, some may need some adhesives while others may require some fixings which also contributes to the differences in price. As a result, the determination of the material cost alone can be tricky and even more so when various materials cover varying areas.

With that in mind, the cost of external solid wall insulation generally ranges between £80 to £100 per square metre2. As a result, a small flat can cost from £6000 to £9000 whereas a large detached house can have a price ranging between £21000 to £23000. To earn back your investment in terms of energy bill savings can take a couple of years, but it’s surely worth the try as there are several other benefits associated with installing an external solid wall insulation system. What’s more? Another huge factor that can influence the cost of your system is also the amount of work that’s required, how easy it is to be accessed by the installers and lots more

If you’re looking to cut down on the cost of your external solid wall insulation, then the best time for an installation might just be when you’re having another decorating or building project done such as fitting a new roof, window painting, installation of solar PV panels and more. This way, you’ll be able to spread the cost and have a greater value for each penny expended.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.