Find an Insulation Installer you can trust in Tenby.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

With cavity walls being very similar to other type of brick works, it can be quite confusing to figure out the type of wall your property possesses. If your house was constructed after the 1920s, then its highly likely the you have cavity walls, while older houses (houses before the 1920s) are likely to have solid walls. What’s more? If you happen to own a home that was built in the last decade, then it’s very possible that it was built with insulation installed during construction.

An effective way to determine whether or not your property is built with cavity wall is to examine the brickwork on your home’s exterior. The bricks will typically possess a regular pattern if it features cavity walls. In the event whereby the brick work is covered by render, you can also figure it out by taking a measurement of the wall’s width. If the brick wall is beyond 3000mm in thickness ( from the exterior wall to the interior wall), then it probably features a cavity. Meanwhile, a wall that’s narrower is very likely to be solid. Stone walls, on the other hand, may actually be thicker but are most times solid.

In a situation whereby your house is built using steel frame or timber frame, or made using pre-fabricated concrete, there are varying rules that applies when it comes to insulation and should be examined by an expert before any insulation is installed. More often than not, most contractors will have installed special air vents, which can also be a good indicator that a cavity wall insulation has been done.

External Wall Insulation (EWI) is the act of insulating a home by fitting insulation to the exterior parts of the building which in turn improves thermal performance, cuts energy consumption ( savings on energy bill) and also adds to the home’s visual appeal. The systems are built in multiple layers, with the insulation board offering a plethora of options with each being suitable to varying projects and their needs. Installing an external wall insulation comes with a variety of benefits, let’s have a look!

• Thermal Performance Improvement

With EWI, the thermal inertia of the walls are greatly enhanced while also restricting the loss of heat. Ultimately, this lowers heating costs, enhances the comfort of indoor thermal and also reduces CO2 pollution.

• Eliminates Noise Pollution

When the noise levels are high, it can have a bad impact on our overall well being. A great way to reduce the disturbances from the outside like traffic noise is by fitting an External Wall Installation system.

• More Comfortable Living Space

Do you know the damp in homes can contribute to respiratory problems? A properly insulated home will greatly limit the impact of condensation by combating the damp issues. As a result, you can always expect your house to be cosy and comfy irrespective of the season. A cooler summer and warmer spring is guaranteed with EWI.

• Enhances The Property’s Visual Appeal

Looking for an excuse to rejuvenate your home’s aesthetic appeal? Well, you can as well try out adding an EWI system. There are a plethora of unique colours and styles you can pick from to beautify your home effortlessly.

• Adds Value To Property

An insulated home will generally cost more than an uninsulated one at the time of resale. Potential home buyers are more interested in the acquisition of a home with an EWI system due to its various benefits - and a higher demand can only imply a higher price!

In recent times, more and more home and property owners are starting to come to terms with the large returns and little investment in cavity wall insulation provides. For a relatively little amount you can achieve a lot, from an increase in your home’s energy efficiency and reduction in heating bills to a huge boost in your property’s resale value and lots more. This makes you wonder how an ordinary insulation can help you achieve so much, right? Well, you’re definitely not alone! Several other potential investors are also eager to know exactly how the cavity wall insulation works to deliver all these juicy benefits. In this post, we’re going to go provide you with a detailed insight on how cavity wall insulation works. Let’s take a look!

Typically, cavity wall insulation works as acting as a shield which prevents the escape of heat from your home. It features a reflective surface which serves as a barrier to reflect heat from one side of the panel, effectively minimizing the amount of heat conduction that escapes through. This protection of your home from heat penetration comes with a couple of benefits with the obvious one being an incredible thermal efficiency. An insulated home or property is able to maintain a much more balanced temperature throughout the year – staying a lot cooler during the summer months and retain the heat generated during the winter months. However, a less talked about benefit is the fact that when an insulation is done during the construction of a house, the whole development phase can be completed a lot quicker. This is mainly because insulation offers total protection against weather conditions which enables internal trades to continue without the need to wait for brickwork or cladding to be completed.

This depends on the amount of insulation already present in your property. However, adding insulation has been proven to improve the energy efficiency of your home and decrease your heating bills, this is more obvious in older properties or where single glazing is still in situ.

Do you know about 25 percent of heat that escapes from an uninsulated house are lost through the roof? Fortunately, roof insulation is something that can done by all DIYers irrespective of their experience levels. However, if you happen to lack the confidence necessary to pull off this, then it’s strongly recommended that you hire the services of a professional who can guarantee the best results and also save you time and money that could arise from potential cost mistakes. Let’s take a look!

• Clear out all clutter. This involves taking out all the rubbish and clutter from the loft. In order to work effectively, you’ll need a totally clear and empty loft space.
• Ensure that there’s sufficient insulation. The importance of a good ventilation cannot be overstated. Poor ventilation will result in forming of condensation and this condensation can make the roof timbers rot and compromise the structural integrity of the entire roof. If there are no roof windows which is the easiest way to provide a loft ventilation, the next best option would be to follow the loft floor along to the point where the roof comes down to meet it. There should be a gap at this point, also referred to as the eaves, between the outside wall and the underside of the roof.
• Measure your loft area. Take a measurement of the loft space in order to calculate the amount of insulation as well as the type you need. If you’re not sure, always get more that it’s required as skimming on the amount you use will only back fire in form of increased energy costs
• Check for water pipes.

To get started, simply make sure all cracks and gaps in the ceiling are filled using a standard filler or decorator caulk. Once done, clean the gaps in the joists and even to the point of hovering all the dust up. Finally,check for the hazards that can cause you problems before laying the loft insulation.

Over the years there has been an increase in the recommended thickness of loft insulation by the government. Obviously, the reason behind this is pretty simply - the thicker the layer of your loft insulation the bigger your savings. The UK government is very keen to every house in the country to have loft insulation fitted where possible as it helps to minimize the heating demands of these properties. Households get to benefit from loft insulation in so many ways which includes reduced energy energy bills as well as having a home that stays at a more comfortable temperature for longer.

Generally, for the government energy efficiency is crucial as it implies that the highest demand ( which is usually the time of the day when gas or electricity use is at its peak ) reduces, since each building requires slightly less energy. Overall, that ultimately implies that new power plants don’t have to be built which is some nice cost savings for the government.

In the 1980’s, any thickness of loft insulation from 25 mm to 50 mm was considered the standard. But then, building regulations stated that homes should have as much as 100 mm of loft insulation. Over time, this gradually increased to 270mm for new builds and also recommended for other properties, although not essential. As a result of this, there’s always a need to check how much insulation you currently have in your loft before you decide to purchase more. You may discover that you already have something within the range of 20 mm to 200 mm up there and knowing this and the insulation values will assist in determining how much more you’ll need to purchase, if any at all. You should also note that some modern materials can offer the same thermal insulation whilst not being as thick.

With the numerous benefits that comes with the installation of an external wall insulation in a building, it’s also important to find out whether it’s also safe before proceeding to fit one in your home. Firstly, to ensure that external wall insulation systems are safe, they must be BBA approved, which means they’ve been subjected to a thorough testing by the British Board of Agrement and therefore, suitable for use in UK homes.

Given the fact that cladding materials have recently generated a lot of debate and negative press about how reliable some particular materials are, questions are being asked of the safety and reliability of external wall insulation. However we must clarify that, although external wall insulation can be classified under cladding, it is very different to rainscreen cladding - which caused the Grenfell fire tragedy.

External wall insulation is completely safe. However, when it comes to fire, the safety of your system depends largely on the insulation type in question. The safest type of insulation you can have installed is the Rockwool insulation boards which are rated as Euroclass A1 non-combustible. The board is specially designed in such a way that it contains fire - preventing it from reaching the other areas of the building. They also do not produce harmful emission or smoke when impacted by fire.

Meanwhile, the Wood Fibre, is also a great insulation which is known to char and not burn. Contrary to many beliefs, it actually burns slowly creating this charring effect which produces an oxygen barrier that helps reduce the spread of fire.

To make your system safer, you can also make use of Fibreglass Mesh for reinforcement. It helps to improve the strength of the tensile which promotes the security of the boards attached to the wall.