Find an Insulation Installer you can trust in Consett.

This depends on the amount of insulation already present in your property. However, adding insulation has been proven to improve the energy efficiency of your home and decrease your heating bills, this is more obvious in older properties or where single glazing is still in situ.

Over the years, more and more home and property owners are beginning to realize the huge benefits that can be derived from loft insulation being a worthwhile investment. It’s quite worrisome the way in which energy bills have soared over the past 10 years and loft insulation is a considerable affordable energy efficiency measure that can go a long way to help increase your home’s energy savings.

As far back as the 1980’s, the standard when it comes to insulation thickness was 25 mm to 50 mm which was, at the time, considered to be sufficient. However, building regulations have changed the norm that now states that a new build needs to possess 270 mm of insulation in the loft in order to achieve the required u-value of less than 0.16/m2k based on the standard rock wool or sheep wool insulation.

Generally with loft insulation, there’s a law of depreciating returns which implies that the first couple of insulation centimetres will save you many times the cost of the installation, however an extra layer or centimetre is going to add less value to the point where it’ll no longer be wise or worthwhile to add any further centimetre. Therefore, with cheaper energy prices 30 years back, that additional couple of centimetres was not just worthwhile, but with the recent alarming rises in costs of fuel, that additional £10 savings per year has all of sudden changed to £30 which makes it become a lot more attractive.

If you already have 270 mm of loft insulation, regardless of the material you’re looking to add you’re most likely not going to benefit from a top up. The cost of the materials and installation will definitely be too high for the couple of pounds it’ll save you per year.

How long it takes to install insulation will depend on the size of your property. In general, loft and cavity wall insulation can be installed in a day or two. External wall insulation will usually take longer to install. The rep or installer will be able to advise you when quoting for the job how long this will be.

If you want to install an external wall, it is only wise to consider whether or not a planning permission is required in order to avoid a hefty fine. In a great kudos to the government and a welcome relief to home and property owners, the installation of external wall insulation is seen as an “improvement to the house and not an “extension or an “enlargement. Ultimately, this implies that external wall insulation fitting is to be done under permitted development and a planning application may not be required. However, like many other regulations, there are also exceptions to this rule and the main one is if the activity changes the appearance of your property. Properties such as a listed building having tighter regulations may pose some issues. As a result, we’d advise you to consult your local authority to ensure that there’s no fast rule to this topic before commencement of the external wall insulation project.

At the moment, according to the Government Building Regulations, the surface of the entire wall is to be improved to existing standards if the area to be insulated exceeds 25 percent of the wall. In normal situations this is usually the typical case, however to prevent avoidable fines and other possible punishments, it is always best to reach to your local authority and check out the rules guiding external wall insulation in your constituency. Furthermore, since external wall insulation is not a task that’s recommended to be done by yourself, you can also ask the professional external wall insulation fitting company for the applying rules before proceeding. As a good professional, the company should have a better knowledge of the rules and regulation guiding its activities.

Insulating a cavity wall should not affect the damp proofing of the wall. All insulation approved for use in cavity walls has been tested to ensure that it does not allow damp to pass through the wall. Some walls which receive a lot of wind driven rain are unsuitable for cavity wall insulation.

In general, you won’t need planning permission to install soundproofing. If you are installing soundproofing against a shared wall, you will usually need to follow the rules and restrictions set out in the Party Wall Act. In listed buildings and conservation areas, there may be extra restrictions on soundproofing.

A lot of an uninsulated property’s heat is lost through the roof and that’s even more alarming, when you realize this figure is up to a quarter of the total heat of the house. Hence, the tremendous importance of preventing this heat loss through loft insulation which will go a long way to help you against spending unnecessary thousands of pounds on heating bill as well as energy loss.

Loft insulation is an effective method to achieve the desired result, however the question is, how exactly does it work? Well, it’s time to find out!

Using either a fireplace or central heating to heat up your home, a large quantity of that heat would be lost through the roof of your home. Generally, heat rises and when it does, there’s simply no way to prevent it - it’s just science. Escaping by both the conduction and convection methods via your roof, the heat escaping through your ceiling, into the loft space and out into the open air outside can only be significantly reduced by laying loft insulation.

Generally, the added layer of insulation works by trapping the heat inside the room below the loft so as to enable the air within your house to stay warmer for longer. What’s more? The layer of insulation also keeps cold air from the outside from entering your home. As a result, you don’t have to heat your home as much in order to achieve the same temperature for each individual room. Over time, just by doing this you can potentially save hundreds pounds. Getting it installed in your home may actually seem a bit expensive at first, but it’s something that’ll eventually pay off.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.