Find an Insulation Installer you can trust in Lochgilphead.

In general, you won’t need planning permission to install soundproofing. If you are installing soundproofing against a shared wall, you will usually need to follow the rules and restrictions set out in the Party Wall Act. In listed buildings and conservation areas, there may be extra restrictions on soundproofing.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

With cavity walls being very similar to other type of brick works, it can be quite confusing to figure out the type of wall your property possesses. If your house was constructed after the 1920s, then its highly likely the you have cavity walls, while older houses (houses before the 1920s) are likely to have solid walls. What’s more? If you happen to own a home that was built in the last decade, then it’s very possible that it was built with insulation installed during construction.

An effective way to determine whether or not your property is built with cavity wall is to examine the brickwork on your home’s exterior. The bricks will typically possess a regular pattern if it features cavity walls. In the event whereby the brick work is covered by render, you can also figure it out by taking a measurement of the wall’s width. If the brick wall is beyond 3000mm in thickness ( from the exterior wall to the interior wall), then it probably features a cavity. Meanwhile, a wall that’s narrower is very likely to be solid. Stone walls, on the other hand, may actually be thicker but are most times solid.

In a situation whereby your house is built using steel frame or timber frame, or made using pre-fabricated concrete, there are varying rules that applies when it comes to insulation and should be examined by an expert before any insulation is installed. More often than not, most contractors will have installed special air vents, which can also be a good indicator that a cavity wall insulation has been done.

If you have a loft, then the next thing that’s crucial is a loft insulation. Asides from cutting down on your carbon footprint, when you’re able to install an effective loft insulation you can slash your heating bills by up to £250 per year. What’s more? Besides making your home more energy efficient, it can also increase the value of your property a great deal. So if you’re also considering the insulation of your loft, one of the few things that comes to mind is, what loft insulation is the best to incorporate? In order to help you make the best informed decision possible, this post is going to address this issue and put you on the right path.

In truth, there’s no way to say exactly which type of insulation is the best as all types usually have a different purpose as well as usage. The insulation you choose for your home’s loft is be based largely on the how you’re going to make use of the space as well as any unique challenges you might face given the shape of your home’s loft. Below are some types of insulation to give you a better idea:

• Blanket insulation. This is the most common type that comes in rolls of rock, glass or mineral fibre ( or foil-backed felt ). It normally the most affordable and also a good all-purpose insulation which is easy to fit although not suitable for the roof.
• Loose-fill insulation. This type of insulation features a loose, lightweight material such as cork granules, cellulose fibre, mineral wool etc. It can either be incorporated as a top up or on its own. The primary drawback is it isn’t very secure and can also be very messy.
• Sheet insulation. This is the best solution for the roof’s underside as it offers a highly effective insulation for your loft space and can also be decorated over. The drawback here is that it’s usually the most expensive type to purchase and install.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.

External Wall Insulation (EWI) is the act of insulating a home by fitting insulation to the exterior parts of the building which in turn improves thermal performance, cuts energy consumption ( savings on energy bill) and also adds to the home’s visual appeal. The systems are built in multiple layers, with the insulation board offering a plethora of options with each being suitable to varying projects and their needs. Installing an external wall insulation comes with a variety of benefits, let’s have a look!

• Thermal Performance Improvement

With EWI, the thermal inertia of the walls are greatly enhanced while also restricting the loss of heat. Ultimately, this lowers heating costs, enhances the comfort of indoor thermal and also reduces CO2 pollution.

• Eliminates Noise Pollution

When the noise levels are high, it can have a bad impact on our overall well being. A great way to reduce the disturbances from the outside like traffic noise is by fitting an External Wall Installation system.

• More Comfortable Living Space

Do you know the damp in homes can contribute to respiratory problems? A properly insulated home will greatly limit the impact of condensation by combating the damp issues. As a result, you can always expect your house to be cosy and comfy irrespective of the season. A cooler summer and warmer spring is guaranteed with EWI.

• Enhances The Property’s Visual Appeal

Looking for an excuse to rejuvenate your home’s aesthetic appeal? Well, you can as well try out adding an EWI system. There are a plethora of unique colours and styles you can pick from to beautify your home effortlessly.

• Adds Value To Property

An insulated home will generally cost more than an uninsulated one at the time of resale. Potential home buyers are more interested in the acquisition of a home with an EWI system due to its various benefits - and a higher demand can only imply a higher price!

This is a very great opportunity to not only get free external wall insulation, but also cut down your energy bills depending on the type of property you live in. Generally, to enjoy free external wall insulation you must at least be part of the group receiving one of the benefits listed below and also depends on the amount of money you earn. The benefits include:

• Income based jobseeker’s allowance (JSA)

• Income support

• Income-related employment and support allowance (ESA)

• Tax credits

• Pension credit guarantee credit.

• Universal credit.

There are also other important factors that determines if you can have a free insulation fitted on your property. These includes the place you reside, the carbon level of your home and according to some suppliers, the level of beneficial impact the insulation will have on your home. In order to have a free external wall insulation installed, you must either be the owner of your home or at least obtain the go ahead from your landlord before any external wall insulation activity can be made.

Good news is, if you fit the aforementioned criteria and you’ve already installed an external wall insulation, you just may be entitled to receive a refund for the good job done. However, to really find out if you’re eligible, we’d recommend you get in touch with your supplier directly. Also, the Energy Saving Trust (EST) can direct you to some organizations who can assist you in the determination of your eligibility.

As a home and property owner living in England, you can also check out the Each Home Counts Advice Website which is committed to giving impartial energy efficiency advice.

At the end of the day, if it turns out you happen to be ineligible for a free external wall insulation, you can still go ahead to contact a professional installer for a help at a competitive price to enjoy the several benefits that comes with home insulation.

This depends on the amount of insulation already present in your property. However, adding insulation has been proven to improve the energy efficiency of your home and decrease your heating bills, this is more obvious in older properties or where single glazing is still in situ.