Find a Heating Engineer you can trust near you.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

How Much To Install A Gas Cooker?

Gas cooker is gradually becoming more and more popular in the UK, with several homeowners looking to have one installed in their various homes. Whether you’re planning remodelling, conversions or perhaps you own a new building, gas ( be it a natural gas or Liquid Petroleum Gas - LPG) is now the favourite mode of cooking ,heating as well as warming across the country.

The fact that it’s popular, however, is not an excuse to install a gas cooker by all means in order to reduce the cost. When it comes to gas cooker installation, adequate care must be taken to ensure costly errors which can lead to fire outbreaks and other dangers are avoided. Therefore, if you’re thinking about getting a gas cooker installed in your home, hiring a qualified gas cooker installation company would be your best bet.

Prior to the installation of your gas cooker, the gas plumber will confirm whether or not your home is connected to the mains gas supply. In the absence of a connection, you’ll have to request for a new service connection. Immediately the connection is available, the certified gas cooker installation company can then proceed to fit in the appliance.

However, for a free standing gas cooker, the measurement of the gas cooker’s dimension will be taken by the fitter as well as the available space for the installation in order to determine whether or not the gas cooker will fit in. After this, the next step would be to turn the gas cooker on its side and fit in the underpins. The gas pipe will then be connected to the manifold while also activating the gas and checking for possible leakages. Once done, the gas would be plugged into the outlet and a test will be conducted on the gas to ensure it’s running the way it should.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

During a boiler service, your boiler engineer will perform a series of checks to ensure that your boiler is safe and efficient. First, they will conduct a visual inspection to check for any corrosion or leaks. They will also check the flame in your boiler. They’ll then remove the boiler casing and check all the components, including the heat exchanger, burner and spark probe, then clean the inside. After this, they’ll check the flue for obstructions and ensure that it’s safely fitted. They will then do a gas pressure check to ensure the boiler is working at the right pressure, before firing it up to check for any working faults.

If you’re looking to have your boiler insured, there are a number of boiler cover providers you should probably check out with British Gas Homecare being right up there as one of the best in the business. In this post, we’re going to consider the British Gas Homecare prices to help you make the best-informed decisions possible moving forward. Let’s take a look!

Firstly, British Gas offers a wide variety of packages to provide coverage for repairs as well as breakdowns on heating systems. They also offer plans which includes cover for your central heating, plumbing, drains as well as electrics. With this provider, you can choose to pay your cover either in monthly instalments or annually. Simply have it at the back of your mind that the cost of your package will depend mainly on the things you want to cover – the more the risk you wish to protect against, the more expensive your package is likely to be.

In general, HomeCare starts from £13 a month (£60 excess). Conditions and exclusions is applicable, prices may also vary based on your property’s postcode. With British Gas, there are a number of products to select from within their range some of which features an annual service and repair of your boiler and controls. Their products include British Gas Home Care One, British Gas Home Care Two, British Gas HomeCare Three and British Gas HomeCare Four. There are also some exclusions, which means that irrespective of the HomeCare product you opt for, there are certain things that British Gas do not cover. For instance, sludge or scale removal and the repair of the damage arising as a result. Showers and their parts, shared drains, faults caused by a non-British Gas engineer and more.

Overall, the amount you pay per month or year will be based on your location in the UK and the British Gas will confirm the price once they’ve been able to take a couple of details from you.

To ensure your boiler is functioning efficiently and to keep your home warm, it’s important to see that your boiler is serviced on a regular basis by a licensed boiler engineer. Failure to do this can result in sudden boiler breakdown which can be a hard hitting blow to one’s financial power especially when there’s no boiler cover to cushion the blow or totally avoid it all together.

When your boiler is covered, it implies that you’re protected in the event whereby your boiler or it’s controls malfunctions or break. Several boiler cover will include the servicing cost, while some may not so it’s advisable to always go through the details, no matter how small, before entering into a boiler cover agreement. Typically, a boiler cover will cost between £60 to £100 per year and the payment is made on a monthly basis. Various boiler insurance companies have varying cover cost, however, here are the common boiler cover policies:

• Homeserve charges from £13 per month

• EDF Energy costs from £13.29 per month

• British Gas from £12 per month

• Scottish Power from £13.13 every month

• CETRI UK charges from £13.50 every month

• 24/7 home rescue costs from £9.60 every month

• Gorgi Home Plan costs from £6 per month plus 3 months free

• Your repair charges from £9.60 per month

• NPower Boiler Cover costs from £10.92 every month

• SSE Boiler Breakdown Cover charges from £4.95 every month

It’s important to note that sometimes you have the option of adding your boiler cover to your existing home insurance, if you do not want a standalone policy for your boiler cover. In many scenarios, this is referred to as an extra or add on service referred to as “Home Emergency Cover. When compared to the standalone boiler policies, this is usually a lot cheaper as it comes in around £5 per month.