Find a Heating Engineer you can trust in Oswestry.

Can I Repair My Own Gas Boiler?

If you’re more of an handy person, then you’d probably want to fix everything you can around the house while saving yourself some money that would have been spent on hiring a professional instead. This is a very cost effective but at the same time you must know that some tasks are usually more difficult than others, and a good example of those complex tasks is boiler repair. Not only can this be very tough, but they can also potentially be one of the most dangerous home appliances you can acquire. So with that in mind, what can be done to ensure your gas boiler is taken care of and in the event whereby it starts to malfunction, what can be done to remedy the situation?

With regular maintenance and repair of your gas boiler, you’d have absolutely nothing to worry about. However one of the fear several DIYers have is the fact that they might just end up incurring more expenses on services they didn’t really need in the first place. But when it comes to gas boilers, it’s necessary to be certified to work with them as it’s very dangerous to tackle it all by yourself. Despite this, there are still some minor issues that you wouldn’t need to hire a technician to resolve. In some cases, all that would be needed is simply to reset the boiler. To identify where the reset button is, simply go through your boiler’s manual for more information. Most times, all you’ll have to do is press down the reset button for a couple of seconds. If the boiler isn’t fully restored to its normal proper functioning state after two resets, then you may need to call in a professional for help.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Are you worried about blocked drains? Yes, you probably should! As a homeowner ( with a detached, semi detached or terraced house), all plumbing and drainage issues within your home or even within your property boundary is your responsibility. Hence, you’d might want to consider getting a Homeserve plumbing and drainage cover to help keep your home running smoothly and putting your mind at ease. The only exception here is if the drain in question is a lateral drain which is a common feature in flats. In this situation, it’s only the building managers that would be responsible for the maintenance of the drainage as it’s shared between several homes. Before 2011, the various flats or houses that shares the lateral drain are responsible for its maintenance.

Working with top utility companies for over 2 decades, Homeserve has positioned itself as one of the leading home assistance providers in the United Kingdom. With their top notch services, they’ve been able to make their client’s lives a lot easier and stress free through the provision of a wide array of repair solutions such as drainage, plumbing, heating, electrics and a lot more.

As a homeowner with the responsibility of maintaining the drains and ensuring there’s no block or damage, it’s simply a no brainer to go for a plumbing and drainage cover and more importantly, get good cover. Homeserve are one of the providers but there are a number of others which offer great service at competitive prices. Without an insurance in place, you may just have to break the bank just to have an engineer or plumber to fix any plumbing or drainage issue you might have. So why not give yourself a peace of mind and get a cover today?

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your business property, it’s only reasonable not only to expect the boiler to warm up your property efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several commercial gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.

In recent times, home and property owners are constantly looking for ways in which to enhance both energy efficiency and sustainability especially as the world draws closer and closer to energy-efficient technology. The Nest thermostat is a great example of this fact as its designed in such a way to save energy while also cutting heating and cooling costs. And an interesting fact is, you’re not limited to using just a single Nest thermostat in your home as multiple of the device can successfully run together to maintain a consistent level of temperature monitoring as well as energy efficiency. What’s more? You can add up to 20 Nest thermostat and 18 temperature sensors in a home.

It’s very unlikely that you’re going to need this many thermostats in your home, but if you’d like to add a second the process is quite straightforward. However, we’d recommend you employ the services of a seasoned professional especially if you lack the required training or experience to pull this off to save yourself some time and money.

To get started, simply download the associated Nest app to add Nest devices. Now let’s have a look at the processes involved in adding a second Nest thermostat to your home.

• Open the app.

• Go to the top left corner of the main screen and click on the menu button.

• Pick the location or home you’re adding the device to.

• Go to the top right corner and select the “settings.

• Once done, then click on the Add Product “Plus button.

Upon a successful addition of the second thermostat, the app will guide you through the initial set up steps. Google also offers a very helpful guide if you’re unfamiliar with the initial configuration.