Find a Heating Engineer you can trust in Welshpool.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

If you get the right size boiler for your home and you get it serviced regularly, your boiler could last up to 15 years. It may even last longer than this, but you’ll find that your boiler begins to become less efficient as it gets older. Also, as technology improves, a boiler older than 15 years may not be the most efficient one on the market.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

How Often Should You Service An Oil Boiler?

If you have an oil boiler, you probably know the importance of having it serviced to ensure its proper functioning, prolong its useful life as well as ensuring the safety of your home. However, the question that most frequently arises is how often would one need to service the prized hating system? If you’re also looking for the answer to this same question, then you’ve come to the right place. To make sure your oil boiler is running smoothly, safely and efficiently, it should be serviced as often as once in a year. You certainly do want to know the numerous disadvantages of failing to service your boiler. Not only will neglecting your oil boiler service result in possible faults as well as higher energy bill caused by its inefficiency, but can also lead to your warranty ending early.

Therefore, you should ensure your oil boiler is serviced by a qualified heating engineer on an annual basis to make sure it’s running just as it should. This will give you peace of mind knowing you wouldn’t be spending huge bucks on possible repairs and in some cases, replacements.

As a landlord in the UK, it’s a legal requirement to make sure that your oil boiler and flue system is services on a yearly basis in your rental property.

Unlike a gas and oil boiler, an electric boiler do not require the same level of maintenance or servicing. However, it’ll be a nice move to ensure that it’s also checked once in a while.

Overall, it’s important to note that failure to service your oil boiler on a yearly basis can give rise to multiple risks. These includes a rise in energy bills, carbon monoxide leak, fault that can cause boiler breakdown as well as an expensive repair or replacement bill.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

• Switch off your boiler and let it cool completely

• Make sure both ends of your filling loop are attached

• Open both valves to allow cold water into the system – you’ll hear it start to move

• Look out for your pressure gauge to show 1.5 bar

• Close both valves

• Switch your boiler back on

• Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

Who Fixes Boilers?

With boiler running for several hours in a day and working hard to ensure that our home stays warm, even when we tend to take it for granted it’s always there give us the heat we need whenever we need it. So in the event whereby the inevitable happens and your boiler breakdown, which professional is the most suitable to call for help? When the pressure is on to stop a boiler leak or bring back warmth to your home, knowing who to call can make all the difference.

When you need a professional to fix your boiler, the right professional to call is a heating engineer. Heating engineers work mainly on heating I both homes and businesses, so you’d be right to call them specialists in all heating matters. As a result of this, you may want to give them a call when experiencing some issues with your boiler as they’d be in the best position than any other professional to give you a proper solution.

Generally, heating engineers are experts when it comes to fixing boilers and can help with various tasks such as installing a new boiler, boiler repairs, installing new gas pipes, repairing gas leaks, changing radiators, fixing leaks, installing heating controls and many more. What’s more? A boiler repair has to do with working with gas and before you can do that you must be a Gas Safe registered engineer as required by the legislations in the UK. In other words, any gas boiler related issue must be tackled by a Gas Safe registered engineer as this is a very dangerous fuel in which the services must be provided to highest standards of safety. Only heating engineers can be a Gas Safe registered engineer to work on gas boilers.