Find a Heating Engineer you can trust near you.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

Is Electric Heating Expensive?

Well, electric heating being termed as “expensive is relative to your budget. But we can tell you making use of electric heating will cost you within the range of an additional £300 to £400 per year more than the conventional gas powered systems. Meanwhile the average UK home making use of heating has been found to incur around £550 on an annual basis while those using electric storage heaters will spend almost £900 every year, according to OVO Energy.

However, there are numerous benefits of using electric heating and some of which can contribute to give a lower cost. If you’re considering the installation of an electric heating, here are some of the benefits you’ll derive.

• Safety. The several risks that comes with traditional systems are greatly reduced with an electric heating system. For instance, there’s no risk of carbon monoxide emissions or potential explosions since there’s no use of fuel to run the system.

• Installation. When compared to traditional systems, electric heating quite inexpensive to fit. This is due to the fact that minimal hardware are needed in the installation - no pipes, no flues, no vents and no ducts to be used. As a result, electric heating systems can also be installed within a shorter period of time.

• Environment. Generally, electricity has a positive impact on the environment especially due to the fact that there are no gasses or heavy metals incorporated in the system’s make up.

• Control. Electric heating offers a more convenient and controllable system. What’s more? This does not only make life easier, but can also help save as much as 30 percent on yearly cost of heating as well as helping to minimize toxic carbon emission. Furthermore, there’s a built in Wi-Fi that usually comes with electric heating systems while same can not be said of traditional gas systems.

Modern oil boilers do not require a lot of maintenance. OFTEC recommends that oil boilers are serviced and inspected every year. This keeps them running as efficiently as possible and will ensure any issues with your boiler are identified before they cause bigger problems. This servicing is also vital because of the increased risk of carbon monoxide leaking from a poorly maintained boiler.

Can You Get Oiled Fired Combi Boilers?

Absolutely! Oil fired combi boilers are not only a super cool alternative to gas heating, but also offer a cost-efficient means of heating your home. And this is best enjoyed especially if you’re one of the estimated 4 million houses that are not connected to the gas network.

Oil fired combi boiler enables you store fuel close to your property and fill it as required. There many A rated model options available in the market with the modern oil fired combi boilers confirmed to be up to 95% efficient. As a result of their multiple advantages over alternative heating systems, the oil fired combi boiler is expected to increase significantly in the UK. Here are some of the advantages of adding the system to your property.

• Oil fired combi boiler heats up water on demand while also saving a lot of fuel and being super energy efficient.

• Since oil needs more fuel than gas, a great return would be derived from every unit of energy.

• When compared with the other types of boilers, oil fired combi boilers have a considerably lower operating cost.

• A new oil fired boiler typically has a 92% to 95 % efficiency, which is significantly better than the 60% to 70% in older systems.

If you have an idea of how to operate the gas-powered alternative, then operating an oil fired combi boiler shouldn’t be an issue. In a similar way to the alternative, the boiler simply delivers the central heating through the radiators and hot water via your household’s taps.

However, the major difference between the two is the fact that the oil fired boiler needs a regular supply of oil, which is stored in a tank. The hot water supplied by the system is instant as it is connected to the water mains supply.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

During the cold months ( winter), there’s a high chance for a more frequent occurrence of faults and breakdowns of your boiler as this is the time in which more strain is being placed on the device. Unfortunately, this is exactly the time in which you’d wish to derive maximum benefits from your boiler to keep you warm all through the winter. As a result, home owners are given no other option than to pay the mega boiler repair bills to keep themselves warm and cosy all winter long. There is, however, an option which can greatly soften the blow and that’s having a boiler breakdown cover.

Boiler breakdown cover provides coverage for cost of hiring an engineer to get your boiler back to a top condition while also paying for the parts as well as labour needed to resolve the boiler’s fault. To select a boiler breakdown cover, you should take into account factors like whether or not the policy provides coverage for limited or unlimited call-outs within the coverage period. You should also ensure to go through the terms and conditions of the cover if you can stake a claim if your boiler were to be damaged by a different thing in your central heating configuration or a persistent fault.

There are an array of boiler breakdown package types with little differences which relates to one or more of the following:

• The package monthly cost

• The call outs excess to be paid

• The nature of the helpline. It may be a 24/7 service or just a few selected hours of the day.

Therefore, to answer the question of which boiler breakdown cover, you’d have to compare the different packages to determine the most suitable one for both your needs as well as pocket.

In recent times, home and property owners are constantly looking for ways in which to enhance both energy efficiency and sustainability especially as the world draws closer and closer to energy-efficient technology. The Nest thermostat is a great example of this fact as its designed in such a way to save energy while also cutting heating and cooling costs. And an interesting fact is, you’re not limited to using just a single Nest thermostat in your home as multiple of the device can successfully run together to maintain a consistent level of temperature monitoring as well as energy efficiency. What’s more? You can add up to 20 Nest thermostat and 18 temperature sensors in a home.

It’s very unlikely that you’re going to need this many thermostats in your home, but if you’d like to add a second the process is quite straightforward. However, we’d recommend you employ the services of a seasoned professional especially if you lack the required training or experience to pull this off to save yourself some time and money.

To get started, simply download the associated Nest app to add Nest devices. Now let’s have a look at the processes involved in adding a second Nest thermostat to your home.

• Open the app.

• Go to the top left corner of the main screen and click on the menu button.

• Pick the location or home you’re adding the device to.

• Go to the top right corner and select the “settings.

• Once done, then click on the Add Product “Plus button.

Upon a successful addition of the second thermostat, the app will guide you through the initial set up steps. Google also offers a very helpful guide if you’re unfamiliar with the initial configuration.