Find a Heating Engineer you can trust in Elgin.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How Much Does A Boiler Repair Cost?

An annual service for your boiler might not seem important and may be easy to postpone to another day, but when it happens to breakdown due to lack of adequate attention, this can be quite painful and also costly.

Before you start thinking about the cost of repairing your boiler, the first thing you’ll need to confirm is whether or not your boiler is still covered by the manufacturer’s warranty. You’d be amazed some warranties can last for as long as 12 years, if yours is still on then you can save yourself a huge amount of of money on your boiler repair. As a result, it’s always crucial to keep the details of your warranty somewhere safe, so you can read them from time to time. You never can tell when the rainy day will come!

Most boiler warranties will require your to get your boiler serviced on an annual basis by a licensed and qualified technician. The cost of an annual boiler service is affected by the time of the year you wish to get it done. When boilers are less useful during the summer months, an annual service is usually relatively cheap when compared to the cold months. Around this period, a boiler service will normally cost within the range of £100 to £150, however for a more accurate quote it’s advisable to contact a couple of professionals and compare their quotes.

The cost of getting a boiler repaired will be affected by a couple of factors including your boiler’s make, the age of the boiler as well as your location and how urgent you need it done. If you have a dead boiler, the cost will typically range from £96 to £348 and a boiler displaying a fault code will cost within the range of £90 to £275. Generally, repairing a boiler will cost within the range of £90 to £400 based on the several factors stated above.

How Long Does A Gas Safety Certificate Last?

As a result of faulty installation and irregular maintenance of gas appliances and chimneys, a lot of people have been met with an untimely death caused by the toxic gas - carbon monoxide. This is a gas that’s completely odourless, colourless and tasteless - meaning you can’t identify one of its in the environment. But what you should know is, if you stay in an environment filled with carbon monoxide, you’d probably be dead within a couple of hours. Consequently as a landlord, you must do what’s best to ensure the safety of all your tenants by making sure that all your gas appliances and chimneys are subjected to annual check by an approved Gas Safe engineer as required by the law.

Wondering how long a Gas Safety Check will take? The safety of your gas is guaranteed by carrying out regular examinations. Whether or not you possess a gas alarm, it’s still vital to conduct regular gas safe checks to make sure your home is safe. A typical gas safe check would last between 30 to 60 minutes for a normal domestic property. However, in the situations whereby a need for repair arises, it may take longer time to complete. Other factors that can also affect the timing includes includes both the size and location of your property.

So how long does a gas safety certificate last? The simple answer to this question is 12 months. If you own a rental property in the UK, it’s up to you to ensure all your gas appliances and chimney is check after every 12 months to obtain a Gas Safety Certificate which you should hand out a copy to all tenants living in your property. However, if you don’t own the property, you can inform your landlord to get one as soon as possible while also providing a carbon monoxide alarm.

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

How Often Should You Service An Oil Boiler?

If you have an oil boiler, you probably know the importance of having it serviced to ensure its proper functioning, prolong its useful life as well as ensuring the safety of your home. However, the question that most frequently arises is how often would one need to service the prized hating system? If you’re also looking for the answer to this same question, then you’ve come to the right place. To make sure your oil boiler is running smoothly, safely and efficiently, it should be serviced as often as once in a year. You certainly do want to know the numerous disadvantages of failing to service your boiler. Not only will neglecting your oil boiler service result in possible faults as well as higher energy bill caused by its inefficiency, but can also lead to your warranty ending early.

Therefore, you should ensure your oil boiler is serviced by a qualified heating engineer on an annual basis to make sure it’s running just as it should. This will give you peace of mind knowing you wouldn’t be spending huge bucks on possible repairs and in some cases, replacements.

As a landlord in the UK, it’s a legal requirement to make sure that your oil boiler and flue system is services on a yearly basis in your rental property.

Unlike a gas and oil boiler, an electric boiler do not require the same level of maintenance or servicing. However, it’ll be a nice move to ensure that it’s also checked once in a while.

Overall, it’s important to note that failure to service your oil boiler on a yearly basis can give rise to multiple risks. These includes a rise in energy bills, carbon monoxide leak, fault that can cause boiler breakdown as well as an expensive repair or replacement bill.

The short answer to this is no! Smart thermostats can still be used without WiFi, however, they’ll be deprived of some certain capabilities and innovative features that comes mainly due to their ability to connect to the internet. As a result, the smart thermostat will only be functional for basic task such as heating and cooling control. In other words, making use of a WiFi connection will be in your best bet to enjoy the multiple juicy benefits that comes with a smart thermostats such as remote monitoring, ability to connect to other devices and display local weather conditions and much more. And what’s the use of purchasing a smart thermostat if you’d not be able to enjoy these remarkable features?

However, even when you have a WiFi, it’s expected for the connection to fail at times. When this happens, what will be the impact on your smart thermostat? Let’s have a closer look!

• As you would have expected, when your smart thermostat is disconnected from WiFi, features that are controlled with the mobile app would all be impacted. And this might be a big headache when you wish to access these features and control remotely when far away from home.

• When your smart thermostat connection to WiFi fails, all live updates and alerts would be affected. This implies that you’d stop seeing updates, reports and notifications on your mobile device. As a result, you’ll not be notified in case of an emergency like electricity cut-outs, water leaks, humidity and temperatures exceeding the set levels as well as thermostat’s low battery.

• The lack of a WiFi connection might have taken away all the juicy advantages of having a smart thermostat, but one function that remains unaffected is the basic one - the control of your home’s heating and cooling system. In other words, if your smart thermostat is offline, your home will still be heated and cooled to the thermostat’s set temperature.