Find a Heating Engineer you can trust in Thornton-cleveleys.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

Installing your Nest thermostat may not be as easy as screwing a light bulb, but we can also assure you that it isn’t very difficult either. However, if you lack the needed training or experience to pull it off, we’d recommend you hire the services of a professional in order to save yourself some time and money. This guide will give you some quick and easy steps to follow and ensure you make no errors during the installation process.

Once installed removing the Nest Thermostat can be done. To get started, you’ll need just a Philips head screwdriver which Nest has thoughtfully provided with the device.

• Turn off the Nest Thermostat by switching the circuit breaker to the off position.

• Label or mark your old thermostat’s wires. However, if you notice your thermostat is tagged 120v or 240v, or possesses thick wires, do not connect the wires to the Nest as you have a high voltage system.

• Uninstall the old thermostat by locating detaching the wires coming out from the wall into the thermostat. Once done, simply unscrew the device from the wall

• Mark the spot of your thermostat. Do this by threading wires through the Nest base plate’s centre incorporate the tiny bubble level. Once done, you can then use a pencil to mark te two screw holes.

• Attach the trim plate. If you wish to cover the screw holes, simply install the trim plate in the Nest box’s bottom to the base plate.

• Using the screws and screwdriver, attach the Nest base to the wall.

• Connect the wires to the Nest by putting the labelled wires in the Nest’s corresponding ports.

• Put the Nest display by lining up the connector on the display’s back.

• Turn on the power by switching the circuit breaker to the on position

• Connect your Nest thermostat to the WiFi network.

• Follow the on-screen guide and set the temperature.

• Use your smartphone or tablet to download the Nest thermostat’s mobile app to monitor and control your device remotely.

Is Electric Heating Expensive?

Well, electric heating being termed as “expensive is relative to your budget. But we can tell you making use of electric heating will cost you within the range of an additional £300 to £400 per year more than the conventional gas powered systems. Meanwhile the average UK home making use of heating has been found to incur around £550 on an annual basis while those using electric storage heaters will spend almost £900 every year, according to OVO Energy.

However, there are numerous benefits of using electric heating and some of which can contribute to give a lower cost. If you’re considering the installation of an electric heating, here are some of the benefits you’ll derive.

• Safety. The several risks that comes with traditional systems are greatly reduced with an electric heating system. For instance, there’s no risk of carbon monoxide emissions or potential explosions since there’s no use of fuel to run the system.

• Installation. When compared to traditional systems, electric heating quite inexpensive to fit. This is due to the fact that minimal hardware are needed in the installation - no pipes, no flues, no vents and no ducts to be used. As a result, electric heating systems can also be installed within a shorter period of time.

• Environment. Generally, electricity has a positive impact on the environment especially due to the fact that there are no gasses or heavy metals incorporated in the system’s make up.

• Control. Electric heating offers a more convenient and controllable system. What’s more? This does not only make life easier, but can also help save as much as 30 percent on yearly cost of heating as well as helping to minimize toxic carbon emission. Furthermore, there’s a built in Wi-Fi that usually comes with electric heating systems while same can not be said of traditional gas systems.

Yes. Modern condensing oil boilers are ‘A’ rated and therefore as efficient as comparable gas boilers. They come with the same controls as gas central heating systems, so you can still use a thermostat to control your heating efficiently. Also, oil is more efficient as a fuel source than gas, so you will get more energy per unit of oil. Oil prices can fluctuate, however, so ensure that you find a good supplier.

Are you worried about blocked drains? Yes, you probably should! As a homeowner ( with a detached, semi detached or terraced house), all plumbing and drainage issues within your home or even within your property boundary is your responsibility. Hence, you’d might want to consider getting a Homeserve plumbing and drainage cover to help keep your home running smoothly and putting your mind at ease. The only exception here is if the drain in question is a lateral drain which is a common feature in flats. In this situation, it’s only the building managers that would be responsible for the maintenance of the drainage as it’s shared between several homes. Before 2011, the various flats or houses that shares the lateral drain are responsible for its maintenance.

Working with top utility companies for over 2 decades, Homeserve has positioned itself as one of the leading home assistance providers in the United Kingdom. With their top notch services, they’ve been able to make their client’s lives a lot easier and stress free through the provision of a wide array of repair solutions such as drainage, plumbing, heating, electrics and a lot more.

As a homeowner with the responsibility of maintaining the drains and ensuring there’s no block or damage, it’s simply a no brainer to go for a plumbing and drainage cover and more importantly, get good cover. Homeserve are one of the providers but there are a number of others which offer great service at competitive prices. Without an insurance in place, you may just have to break the bank just to have an engineer or plumber to fix any plumbing or drainage issue you might have. So why not give yourself a peace of mind and get a cover today?

To ensure that your boiler is safe and operating efficiently, it’s essential to have it serviced on a regular basis.

Generally, a boiler service will deliver a wide array of benefits which includes the opportunity to identify safety issues like a possible leak of carbon monoxide, efficient use of energy and reduction in energy bills, prevention of breakdowns, a valid warranty when the boiler is serviced regularly by a qualified engineer as well as an extended lifespan. So what exactly does a boiler service cover? This guide will give you a good insight as to what happens during that service.

Before we get started, it’s very important to note that the work done is always as good as the engineer you employ. Therefore, it’s advisable to make sure your preferred engineer is qualified before proceeding with the service. Below are some of the basic practices the engineer may perform during their visit.

• Thorough Inspection

During the visit, the engineer will carry out a detailed examination of your boiler to ensure it still meets the current standards while also making sure that there are no leaks or corrosion. What’s more? They’ll also examine the boiler’s flame for any faults.

• Boiler Casing Removal

The boiler casing will be detached to check all components and ensure they’re free from all forms of dirt and see to it that they’re all working just as they should. This will include examination of the heat exchanger, main injector, burner and spark probe.

• Flue Examination

The engineer will inspect the flue terminals to make sure there are no form of obstructions and it’s also safely installed.

• Gas Pressure Examination

This is done to make sure the heating system is operating at the right pressure.