Find a Heating Engineer you can trust in Hythe.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

How Often To Service Boiler?

A boiler is a vital part of any home especially if you’re in the UK. Not only does provide your entire household with hot water and keep them warm but also adds a good value to your property. Boiler repairs and replacement are both super expensive and stressful, so in order to avoid all these worries, it’s better to have your boiler serviced on a regular basis for your own peace of mind. When you call in a reliable heating engineer, it can immensely raise your boiler’s efficiency while also saving you from more expensive issues down the road.

So if you haven’t had your boiler serviced for quite some time, moved into a new house and not aware the last time your boiler was serviced or perhaps you’re just wondering how often a boiler should be serviced, then you’ve come to the right place! The short and simple answer to this question is a boiler should should be serviced once in a year, and most preferably during the summer months. However, there are a wide range of factors that comes into play so it’s always advisable to check with your manufacturer before you proceed.

According to the law, you’re required to have your boiler services on an annual basis. Failure to do so can render your boiler or home warranty void. Therefore, it’s very crucial to take down the last time your boiler was serviced and also set a reminder to book your next appointment when the time closes in.

If you happen to own an electric boiler you may not need an annual servicing. But you may still be required to perform it annually by your insurance provider.

Breakdowns of boilers are quite common during the winter months and are usually very expensive to repair when this occurs. According to the research carried out recently by uSwitch, repairing a boiler can cost an average of about £314 with a figure over 20 percent of homes experiencing various heating system issues last year.

To answer the question of whether or not your existing home insurance will be enough to cover the boiler breakdown, the answer is probably not. This is due to the fact that heating system faults or breakdowns is a very common occurrence and as a result of poor maintenance practices as well as a high repair cost, several insurance companies often remove it from their home insurance policies.

Generally, you’d be given an option of what is termed as “emergency home cover which is an add on or extra to your home insurance policy. Luckily, this add on is quite inexpensive and may be as little as £4 or £5 per month. Depending on your need or budget, you can also purchase the add on as a “stand alone from your current insurer or another company. However, the stand alone option is usually more expensive.

The emergency home cover normally provides coverage for the boiler repair cost and few times, the rest of the central heating system as well. Being fully aware how important a boiler can be, insurance companies usually deliver a rapid response service as suggested in the name, “emergency home cover. However, the maximum pay out for call out charges is capped at a particular amount which usually ranges from £500 and £1,000. Apart from the call out fees, the emergency cover also includes a limit on the pay out amount for future required repairs of heating systems which includes both parts labour.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

If you’re thinking about getting a new combi boiler, you may be wondering just how much it’s going to cost so as to start making preparations as soon as possible. However, providing a precise cost for the acquisition and installation of a new combi boiler is simply impossible as combi boiler prices vary greatly in price - usually ranging between £1500 to about £3500 based on the brand of the combi boiler, the insurance or warranty, installation, your location as well as the size and power of the appliance. Due to the fact that combi boilers are compact units which doesn’t need a hot water cylinder or a cold water tank to produce heating and hot water for homes, it’s a very popular type of boiler that’s frequently used especially in the UK.

Combi boilers are also widely known to be the most energy efficient type of boiler because they are able to provide an instant supply of hot water anytime you turn on a tap. Combi boilers particularly perfect for flats and houses where space is limited as they have the ability to deliver instant heating and hot water without requiring any extra parts or components.

In the event whereby you’re about to choose a combi boiler for your home or property, it’s always advisable to compare models as well as prices from only the most reliable and sought after brands across the globe. Depending on the manufacturer, the overall quality of the boilers as well as their prices can differ. However, regardless of your budget, you’ll discover there are a plethora of combi boilers available in the market that’ll also suit your taste.

First and foremost, the purpose of a landlord insurance is simple and pretty straightforward. It protects against risks associated with your rental property as well as activity. Most policies start out with building insurance as well as property owners’ liability insurance but you’re absolutely free to include several other covers. These covers can include tenant default or accidental damage, loss of rent and more depending on your needs. It’s important to note that varying types of landlord insurance provides coverage for different sorts of risks. For instance, building insurance provides coverage for the cost of repairing or rebuilding your property, while contents insurance provides coverage for contents if they’re damaged or stolen. However, the question is, does landlord insurance cover boiler? In this post, we’re going to shed more light into this to help you make informed decisions moving forward. Let’s take a look!

The short and simple answer to this question is yes, landlord insurance can definitely cover boiler break down! However, this is usually possible only if you select this option when you purchase your landlord insurance policy. With some boiler cover providers, you’ll have to include a home emergency cover to your landlord insurance so as to cover any form of boiler break down. Once this is done, if the boiler in your rental property starts to malfunction or stops functioning, a Gas Safe registered engineer would be sent to your premises to help out with the situation. With this, the repairing cost of your heating system would be covered by the insurance excluding any excess and up to the limit of your policy.