Find a Heating Engineer you can trust in Hessle.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

The size of boiler you need will depend on the size of your commercial property, how many radiators and bathrooms you have and how appliances willl need hot water at the same time. The boiler size refers to its output, which is measured in kilowatts (kW), rather than the actual dimensions. Speak to your boiler engineer about which boiler is suitable for you, as if you have more than one bathroom or a lot of people in your home a combi boiler might not suit you.

How Much Does It Cost To Move A Gas Meter?

When your gas meter is not in the right location while completing your renovation works or extending your property, it can be a worrying experience.

As a homeowner, you’re not allowed by the law to move your gas meter by yourself - it’s a very dangerous task that’s too risky to undertake just by watching a Youtube video or reading a blog post. Moving of a gas meter can and should only be carried out by a qualified and licensed gas supplier. And this, ultimately, gives rise to the question - how much does it cost to move a gas meter? Before we provide an answer for that, let’s look at what moving of a gas meter entails.

First and foremost, moving of a gas meter typically involves switching off the gas source to your home or property. The pipeline about 2 metres away from your property would be cut into for safety reasons and diverted into another position. Furthermore, you can as well apply that your meter should be re-fitted and re-linked to the inner copper pipeline, but that’s if the inner copper pipeline happens to be within two metres of the new location of your gas meter.

The time involved in the completion of a gas meter re-location project depends largely on the complexity of the job as each project is unique. Typically, the standard timescale from preparation to the final stage of moving a gas meter will take between 4 to 8 weeks. Finally, how much will it cost to relocate your gas meter?

As there are no government funds to subsidize gas meter relocation costs, this can be a very expensive work to carry out. Generally, the price to move a gas meter of about 5m will start within the range of £640 to £670.

If you’re looking for a reliable or reputable source for your new gas boiler, you definitely won’t find much better than British Gas. Using a big firm like British Gas comes with a plethora of benefits , but of course there are also some drawbacks, with the boiler prices being the main one and biggest turn off for most homeowners. However, just before we delve straight in to the price, let’s look at a thing or two about the big company.

The company, “British Gas are not a boiler manufacturer as you probably would have first imagined. They’re actually a company that specializes in the installation of boilers. As a result, they’re able to install just about any type of boiler you can imagine from any manufacturer. Be it a Worcester Bosch Greenstar 8000 Style or a Baxi 600, they’re able to provide you with the cost of having these boilers installed in your home or property.

Combi boilers are perfect boilers for space-saving and this makes them very popular on the market. They’re also very efficient when it comes to heating water instantly and warm your in few minutes. The price of a new British Gas combi boiler varies on a number of factors. Generally, the installation prices of combi boilers start from £1,800. Therefore, if British Gas are to be competitive with their pricing it should also be around this price.

However, if you have a large house with several rooms with a higher demand for hot water, British Gas will most likely recommend boilers such as Worcester Bosch 440CDi and the likes. Judging from other firms in the market, the price to have these types installed should be in excess of £3,000.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.

Modern oil boilers do not require a lot of maintenance. OFTEC recommends that oil boilers are serviced and inspected every year. This keeps them running as efficiently as possible and will ensure any issues with your boiler are identified before they cause bigger problems. This servicing is also vital because of the increased risk of carbon monoxide leaking from a poorly maintained boiler.

How To Fix A Broken Boiler

To fix any problem when it comes to home appliances, the first step is always to identify the problem while also carrying out thorough checks - a broken boiler is not an exception. Putting enough time and effort in diagnosing a problem can go a lot way to save you both time and money. So here are some of the steps you can take to fix your broken boiler before you put a call out to a licensed engineer.

✓ Check to confirm if your pilot light is on. Whenever you’re facing some issues with your boiler, this should always be the first thing you do. The pilot light being on speak volumes, if the light is off then there’s absolutely no way the flame can start the appliance’s gas supply. You should try to put it back on, if off. To do this, you simply have to follow the detailed instructions on your boiler’s manual strictly. If after following these actions to the letter and the issue remains the same, then you’d probably need the services of an a qualified engineer. Never try to fix the issue on your own.

✓ Check the pressure. The solution to the headaches might sometimes be as simple as examining your appliance’s pressure gauge. Here, the good numbers are around 1.0 or1.5, if it happens to fall below this, then you should open the boiler’s instruction manual. You can also inspect your radiator valves for any leaks. You’d have to call in a specialist to solve the issue.

✓ Check the thermostat. Here, it’s important to note that a faulty thermostat doesn’t necessarily imply a broken boiler. It may just signify that you need to replace your thermostat. Simply check to ensure that your thermostat is turned on and temperature is at the appropriate degree.

How To Make Oil Boiler More Efficient?

During the winter months when the nights get darker and colder, it’s more likely your oil gets used up a lot more quickly. This can be very worrisome as it implies having to spend more money to refill. So what exactly can be done to make your oil boiler more efficient and save you some money?

• Regular Servicing Of Your Oil Boiler

Getting your boiler serviced by a manufacturer approved engineer on an annual basis is one of the easiest and quickest ways to ensure that your oil boiler is operating at its maximum efficiency level. When a full servicing is provided for your oil boiler, checks are made to ensure that all components are functioning the way they should while also identifying the bad or worn parts that may be hindering your oil boiler from functioning in an effective manner. As a result, it helps you see to the fact that your boiler is not consuming more than necessary to make sure your oil boiler lasts longer.

• Set Your Thermostats Correctly

When you set your room thermostats and thermostatic radiator valves (TRVs) the right way, you’ll be sure to get a comfortable home without having to make use of much fuel.

• Consider Smart Technology

If you decide to make use of smart technology like Nest or Hive, you can save more money when compared to their more conventional counterparts. These smart technologies incorporate highly advance intelligent systems to get more familiar with your lifestyle, habits as well as heating operations in order to ensure optimum efficiency at all times.

• Put Your Radiators To Good Use

Try as much as possible to avoid some oversights that can make your radiators consume more energy than required. Consequently, you have to keep them clean, give them space and also take care with curtains.