Find a Heating Engineer you can trust in Caldicot.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

The Oil Firing Technical Association or OFTEC operate a competent persons scheme to certify installers. It’s always recommended to use an installer with this certification as it proves they have the training and expertise to properly install your boiler and give you realistic advice on the efficiency of your system. Also, OFTEC registered installers offer Workmanship Warranties to protect you if there are any problems after installation.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.

During the cold months ( winter), there’s a high chance for a more frequent occurrence of faults and breakdowns of your boiler as this is the time in which more strain is being placed on the device. Unfortunately, this is exactly the time in which you’d wish to derive maximum benefits from your boiler to keep you warm all through the winter. As a result, home owners are given no other option than to pay the mega boiler repair bills to keep themselves warm and cosy all winter long. There is, however, an option which can greatly soften the blow and that’s having a boiler breakdown cover.

Boiler breakdown cover provides coverage for cost of hiring an engineer to get your boiler back to a top condition while also paying for the parts as well as labour needed to resolve the boiler’s fault. To select a boiler breakdown cover, you should take into account factors like whether or not the policy provides coverage for limited or unlimited call-outs within the coverage period. You should also ensure to go through the terms and conditions of the cover if you can stake a claim if your boiler were to be damaged by a different thing in your central heating configuration or a persistent fault.

There are an array of boiler breakdown package types with little differences which relates to one or more of the following:

• The package monthly cost

• The call outs excess to be paid

• The nature of the helpline. It may be a 24/7 service or just a few selected hours of the day.

Therefore, to answer the question of which boiler breakdown cover, you’d have to compare the different packages to determine the most suitable one for both your needs as well as pocket.

A terrible day would be walking into your home to discover your boiler is broken - nobody prays for that and even more so, when you’re fully aware a broken boiler can be one of the most expensive things to repair. However, when this occurs, a boiler plan is ready to help cover the repair cost - and that’s only if you’ve gotten one. Generally, cover plans feature only a monthly price which is quite affordable when compared to paying a huge lump sum at once. Furthermore, depending on your cover level, you may not be required to incur call out charges or any other expensive services rendered. And in the event whereby your boiler can’t be repaired, there’ll be plans in place to get a replacement unit. As a result, getting a boiler cover is a great way to give yourself a peace of mind and see to it that you’re not left in the cold when the worse happens.

So the answer to whether or not you should get a boiler cover is totally a positive one. The purchase of a new heating system can be quite costly, but it would even be costlier when you have to repair it ceaselessly throughout it’s service years. With several modern combi units being a complicated heating system to repair, getting a cover plan with unlimited call outs, zero excess as well as cover parts and labour would be a truly wise decision.

In addition, an annual service of your heating system is required by manufacturers in order to make the warranty valid. Therefore, just a basic service plan is very crucial if you do not buy the idea of having to fork out at least £70 for each service.

Installing your Nest thermostat may not be as easy as screwing a light bulb, but we can also assure you that it isn’t very difficult either. However, if you lack the needed training or experience to pull it off, we’d recommend you hire the services of a professional in order to save yourself some time and money. This guide will give you some quick and easy steps to follow and ensure you make no errors during the installation process.

Once installed removing the Nest Thermostat can be done. To get started, you’ll need just a Philips head screwdriver which Nest has thoughtfully provided with the device.

• Turn off the Nest Thermostat by switching the circuit breaker to the off position.

• Label or mark your old thermostat’s wires. However, if you notice your thermostat is tagged 120v or 240v, or possesses thick wires, do not connect the wires to the Nest as you have a high voltage system.

• Uninstall the old thermostat by locating detaching the wires coming out from the wall into the thermostat. Once done, simply unscrew the device from the wall

• Mark the spot of your thermostat. Do this by threading wires through the Nest base plate’s centre incorporate the tiny bubble level. Once done, you can then use a pencil to mark te two screw holes.

• Attach the trim plate. If you wish to cover the screw holes, simply install the trim plate in the Nest box’s bottom to the base plate.

• Using the screws and screwdriver, attach the Nest base to the wall.

• Connect the wires to the Nest by putting the labelled wires in the Nest’s corresponding ports.

• Put the Nest display by lining up the connector on the display’s back.

• Turn on the power by switching the circuit breaker to the on position

• Connect your Nest thermostat to the WiFi network.

• Follow the on-screen guide and set the temperature.

• Use your smartphone or tablet to download the Nest thermostat’s mobile app to monitor and control your device remotely.

What Size Of Electric Boiler Do I Need?

If you’re thinking about installing central heating in your home or property, you’ll be shocked by the plethora of options that’s currently available in the market as regards the boiler type that can be installed. Being a very good alternative to gas boilers or an oil or LPG boiler, electric boilers are here to stay. They usually feature different power outputs which tends to lead to one of the most frequently asked questions about electric heaters - what size of electric boiler do I need? Here, we’ll give you a good insight into sizes of electric boilers available to help you make the right decision.

The importance of getting the perfect size of electric boiler for your home can not be over-emphasized. If your electric boiler size is too small, it won’t be able to provide the level of heat and hot water required. And on the other hand, if it’s too big, it’ll definitely consume more electricity which would be a total waste of money.

To determine the correct size, if you have a wet central heating or water radiators in your home, you’ll need to calculate the boiler’s capacity required to operate them and allow 1.5kw per radiator. To be more accurate, it’s advisable to talk to a professional installer to avoid making a costly mistake. Every professional installer should have an idea of the appropriate size of electric boiler that’ll be needed given your special requirements and home size.

Generally, with a 12k kilowatt boiler, you should be able to operate up to 7 to 8 radiators which is good for smaller properties. For apartments and flats, getting a smaller electric boiler would be the best option.

Can You Replace A Gas Boiler With An Electric Boiler?

In the UK, there are about 22 million households that are heated with the use of a gas boiler. However, do not assume that they’re the best type of boiler to install. The fact is, if your house isn’t connected to the main gas supply, the best option is for you to install an electric boiler rather than a gas boiler. So is it possible to replace a gas boiler with an electric boiler? The simple answer is yes. Both heating system options work in varying ways and also with a different impact on the environment.

The gas boiler is able to generate heat with the help of a gas burner. A heat exchanger is linked to the burner and heats the water available in its chamber. The hot water is then supplied to the heating circuit.

However, the thing is that natural gas can actually be more affordable when compared to using electricity to operate your boiler, but they have a negative impact on the environment. This is because gas boilers make use of an odourless, colourless and poisonous gas - carbon monoxide.

Meanwhile electric boilers are powered by electrical energy, hence, no carbon monoxide leak risks. Instead of using gas to heat up water, electric boilers distribute energy to heating elements which, in turn, heats up the water. So thinking about what’s best for the environment, you’d go for electric boilers. However, they’re more costly and are not as efficient as oil boilers.

If you reside in a smaller house that’s not connected to the main gas supply, then you might want to consider installing an electric boiler. However, if you live in a larger house, an electric boiler may not be the best option as they’re mostly designed to generate little quantity of hot water.