Find a Heating Engineer you can trust in Kirkby Stephen.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.

If you choose to install an LPG boiler, you’ll need to find an LPG supplier. They’ll deliver fuel to you every time your storage tank runs low. You can even rent a storage tank from them if you don’t want to buy one. Make sure you know who your local suppliers are and where they are based.

Many domestic biomass boilers are no bigger than a standard gas boiler. However, they do require a flue, a feeder and a space to store the fuel. These can be designed to suit many different properties and will fit in lots of homes or a garage or outbuilding.

How Long Does It Take To Service An Oil Boiler?

Are you about to service your oil boiler and wondering just how long it would take to completion? Well, you should first know that during an oil boiler service, there are a wide range of things that needs to be checked. As a result, the service can actually take some time and even more, depending on the present condition of your oil boiler.

During a boiler service, your qualified heating engineer will carry out the following tasks:

• Detach and clean both the burner and fan.

• Examine the combustion chamber rope seal.

• Wipe clean and descale baffles.

• Wipe clean and descale the main heat exchanger

• Detach, clean and replace turbulators

• Examine the combustion levels after cleaning.

He’ll also perform some tank and system checks which includes:

• Inspecting and cleaning condensate

• Testing the fire valve

• Cleaning or replacing the filter

• Cleaning the condense trap

• Conducting a thorough inspection of the tank and oil supply pipe to identify possible damages, deterioration as well as debris.

• Pressure testing the oil supply pipe at the point where it goes underground.

• Examining the system pressure.

With all the aforementioned activities and more, an oil boiler service may take relatively longer period of time when compared to it’s counterpart - gas boiler. This is mainly due to the fact that the boiler itself requires a thorough inspection as well as the oil tank where the fuel is being stored. You get your gas through the mains supply, however oil must firstly be stored inside the tank then filled up when it’s almost low. The oil tank will be inspected to identify possible leaks, bulging, corrosion as well as water.

So generally, an oil boiler service should take between the range of 1 to 2 hours to be completed.

Condensing boilers are the in-thing when it comes to modern heating systems in UK homes and across the globe for a good reason. This is primarily due to the fact that condensing boilers happens to be highly efficient as it enables the fuel you’re burning to heat up your home go a lot further. Having a new high efficiency condensing boiler rather than an old G-rated non condensing boiler will not only enhance your heating controls, but also save you a lot of money annually. In this article, we’re going to take you through the basics of a condensing boiler. Let’s take a closer look!

If you’re interested in getting a greener and more efficient boiler, you simply can’t afford to look beyond a high efficiency condensing boiler. This is purely due to the fact that these condensing boilers happens to make a better use of the heat they’re able to produce from burning fuels like oil or gas ( in other words, they require less heat from the burner, which makes them a lot more efficient).

So how does a condensing boiler work? Unlike a non-condensing heat-nly boiler, some heat will be wasted in form of hot gases which are released from the flue. Meanwhile a condensing boiler captures some of the heat from these gases and puts them to use for heating up water that’s coming back from your central heating system. As a result, it requires just a minimal heat from the burner which make the boiler more efficient.

You should take note that all new modern boilers are condensing boilers. Therefore if you’re planning to replace an old boiler with a new one, you’ll definitely be buying a new condensing boiler and benefit from all the efficiency and savings that comes with it.

Your LPG storage tank will need to go outside your property, possibly underground if you have limited space. There are planning rules that restrict where you can put your tank, especially if your property is listed or on designated land. Take a look at our planning permission article to find out more.

When your boiler is being replaced you won’t have hot water or central heating. If you don’t mind this you can stay in your home, and use portable electric heaters if needed. Most installers undertake a power flush before installing a new boiler now and this can cause muck and debris from the pipework, so you may wish to get out of the way while this is happening!

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.