Find a Heating Engineer you can trust in Frizington.

To ensure your boiler is functioning efficiently and to keep your home warm, it’s important to see that your boiler is serviced on a regular basis by a licensed boiler engineer. Failure to do this can result in sudden boiler breakdown which can be a hard hitting blow to one’s financial power especially when there’s no boiler cover to cushion the blow or totally avoid it all together.

When your boiler is covered, it implies that you’re protected in the event whereby your boiler or it’s controls malfunctions or break. Several boiler cover will include the servicing cost, while some may not so it’s advisable to always go through the details, no matter how small, before entering into a boiler cover agreement. Typically, a boiler cover will cost between £60 to £100 per year and the payment is made on a monthly basis. Various boiler insurance companies have varying cover cost, however, here are the common boiler cover policies:

• Homeserve charges from £13 per month

• EDF Energy costs from £13.29 per month

• British Gas from £12 per month

• Scottish Power from £13.13 every month

• CETRI UK charges from £13.50 every month

• 24/7 home rescue costs from £9.60 every month

• Gorgi Home Plan costs from £6 per month plus 3 months free

• Your repair charges from £9.60 per month

• NPower Boiler Cover costs from £10.92 every month

• SSE Boiler Breakdown Cover charges from £4.95 every month

It’s important to note that sometimes you have the option of adding your boiler cover to your existing home insurance, if you do not want a standalone policy for your boiler cover. In many scenarios, this is referred to as an extra or add on service referred to as “Home Emergency Cover. When compared to the standalone boiler policies, this is usually a lot cheaper as it comes in around £5 per month.

How To Install A Gas Cooktop In An Island

Are you thinking about installing a gas cooktop in your kitchen island? If yes, then you must know that there are clearance requirements that must be met (before you proceed) between the cut out and the countertop’s edge. Basically, there are incremental requirements for island installation due to the fact that it does not make an assumption that the product is going to be fitted against a rear wall that acts to protect the back of the unit. As a result, while doing an island install we must put the safety of the product into consideration much more that we do a standard install. What’s more? This island clearance requirement develops from a third-party agency and is a standard with all brands. So how do you install a gas cooktop in an island having the aforementioned requirements in mind?

• Use a foil tape to line the inside edges of the cut out. The function of this is to prevent heat damage as well as countertop’s discolouration. Put the cooktop top on a secured surface.

• Identify the pipe coming out of the cooktop’s side or bottom and brush onto the threads of the manifold entrance.

• Pass the pressure regulator onto the entrance of the manifold and make use of a wrench to tighten it.

• Brush the pipe joint compound onto one of the flare union adaptor’s threads and pass it into the regulator’s open end. Make it slightly tight with a full turn of the wrench.

• Connect the flare union adaptor’s open end with the flexible appliance connector hose, upon brushing on pipe joint compound.

• Put foam tape on the cooktop underside’s edges, if your cooktop comes with a glass burner plate.

• Turn the cooktop to set it into the cutout.

• Apply pipe-joint compound onto the flare union adaptor left and secure it firmly into the gas shutout valve.

• Connect the flexible hose connector’s free end with the flare union adaptor.

How Do Electric Boilers Work?

Electric boiler are installed in residential, commercial and industrial properties to serve as a reliable source of heat. Unlike other types of boilers that depends on fossil fuel burning to be able to operate, electric boilers are fuelled by electrical energy which ultimately makes it more reliable and powerful compared to its counterparts. This heating option was basically provided for home or property owners who don’t have an access to the main gas supply.

So how does an electric boiler work? Basically, an electric boiler work by heating water. Once heated, the hot water supply is then distributed to various areas across the house or property. In order to achieve the best possible efficiency at the lowest possible costs, new model electric boilers are installed by licensed and professional boiler fitters with the help of a microchip control system. Meanwhile, the microchip control system functions to oversee the management of both temperature level as well as output.

Unlike other types of boilers such as a gas boiler, electric boilers only require minimal service. If you own a gas boiler, it’s crucial to ensure that it’s serviced every single year by a licensed and reliable professional that’s into boiler repair services. During the checks and maintenance services, the gas boilers would need to be checked for possible gas leaks, as well as ventilation poisoning and other problems.

Overall, electric boilers are considered to be one of the most environment-friendly heating system which is more affordable to install in your property than a gas boiler. It represents the most ideal option for homes with gas boiler issues as well as those that are not connected to the main gas supply. What’s more? Electric boilers are also one of the best options for wet central heating and under floor heating.

How Do You Bleed An Oil Boiler?

Bleeding air between the oil supply and an oil fired boiler’s burner is a process that’s often required when the system has run out of oil and the burner has stopped working. Upon refilling the oil tank, the air that has been trapped within the oil pipe when empty has to be freed to ensure that the oil reaches the burner and allows it to start again. So how do you go about the process?

First and foremost, it must be noted that it’s always better to be on the look out for the amount of oil in your fuel tank and get it refilled before it runs out. However, if it does run out, you can take the following steps:

• Identify the burner

The burner is a red plastic cover and it’s usually positioned on the bottom part of the boiler (mostly inside the boiler casing). Once identified, inspect it to see if the lockout button is lit red. If yes, simply unscrew and detach the burner’s red case using a flat head screwdriver.

• Identify the oil pump

You’ll find the oil pump on the burner’s left side which is connected to the flexible oil line. Once done, simply locate the 3 inches long hexagonal stem protruding from the pump and with a small threaded plug screwed into the end. Unscrew the plug in just half a turn ( 180 degrees) with a 4mm Allen Key. At this stage oil will be released, do ensure there’s a cloth or rag underneath the plug to grab the oil freed.

• Press the lockout button

This is the next and final step. However it’s also crucial to note that the burner fan will run for about 12 seconds and discharge some oil from the loosened plug which you can grab with a cloth or rag. Immediately you hear a buzzing sound, use the Allen key to tighten the plug. If enough air has been bled, the system will fire. But if not, then you’ll have to repeat the process again.

The Hive thermostat stand is relatively easy to install, however if you lack the necessary training or experience, this is a task you might want to leave to a professional to guarantee the best result while also saving you money and time. This guide will give you a good insight into the Hive thermostat installation process.

The installation of a Hive thermostat does require it to be connected to your home boiler. For this reason we always recommend you get a professional to install it. However once install the Hive Smart Thermostat is very easy to operate and move the controller around your home. To get started, you can follow these steps:

• Press the lever at the lower side of the thermostat and pull away from the front to detach the back plate of your device.

• Once done, simply hang the thermostat on the stand back plate and ensure it holds firmly in place

When it comes to Hive thermostat installation, you might also want to consider the positioning of the device in such a way to heat your home even more efficiently as its designed to be very sensitive to temperature. To identify the best spot for your Hive thermostat, let’s take a look at some of the dos and don’ts.

A Few Dos:

• Do maintain the position of your Hive Thermostat to keep a stable connection with the receive and Hive Hub.

• Do ensure that the position chosen is the centre of your home or a frequently used room.

• Do place the thermostat about 1 to 1.5 metres from floor.

• Do ensure that your thermostat is in a close proximity with the hub and receiver for a better functionality.

A Few Don’ts:

• Don’t place your Hive thermostat stand close to radiators, direct sunlight or other heat sources,

• Don’t position your device near or at places that can expoerience a sudden change in temperature such as the front or back door.

• Don’t leave your thermostat too close to curtains or ornaments.

How To Install An Oil Boiler Heating System

Just like several other skills, the installation of an oil boiler heating system can be a challenge. It requires enough persistence to actually get right, so if you’re the type with little patience, we’d recommend you hire the services of a professional oil boiler heating system fitter who can guarantee the best results and save you time and extra money due to potential damages.

To install your boiler system yourself, it’s always advisable to start by getting the information on the best installation processes from the supplying company which will go a long way to save you from future headaches. However, we’ve put together this guide to give you a basic knowledge on how its done. Let’s have a look!

lRead Instruction Manual

• Carefully read and digest the instruction manual thoroughly.

• Make sure you understand the installation diagrams

• Spread out the materials and get familiar with them.

lFigure Out What Goes Where

• Take your time to determine where everything goes in relation to the others.

• Identify the new radiator’s position.

• Get sufficient sealants to prevent possible leakages inside the walls.

lIdentify The Pipe Routes

• Determine the pipe routes while fitting the new radiators

lInstall The Boiler

• Turn off water and all electrics

• Fit the boiler into the wall

• Make sure the fittings are secured.

lInstall The Radiator

• The effectiveness of your home’s heating system is as good as the radiators you incorporate and how good they’re installed.

• You may have to utilize extra radiators in large open plan kitchens and living rooms (for effective heating).

lOffer Ventilation

• Once you’ve successfully installed the new radiator, a small dose of air ventilation would be needed.

• Turn the key of each valve located at the bottom, do not stop until a little amount of water spills over the top of the unit.

If you get the right size boiler for your home and you get it serviced regularly, your boiler could last up to 15 years. It may even last longer than this, but you’ll find that your boiler begins to become less efficient as it gets older. Also, as technology improves, a boiler older than 15 years may not be the most efficient one on the market.

LPG stands for liquid petroleum gas. It’s a by-product of refined crude oil. When it’s put under pressure, LPG turns into a liquid. It’s usually stored in this form. LPG is used as fuel for things like BBQs and camping stoves, as well as central heating.