Find a Heating Engineer you can trust in Newmilns.

A combination boiler, also referred to as a “combi boiler, delivers both domestic hot water and space heating in a single package so as to save space, and in a lot of cases, money. These great features makes the appliance a very popular choice in UK homes and in fact, it represents more than 50 percent of all new boilers fitted in the UK on a yearly basis.

Most modern and high efficiency combi boilers are usually stainless steel condensing boilers which normally features an in-built secondary heat exchanger to deliver domestic hot water to a home or property. What’s more? When it comes to the heating season or the cold months, the combi boiler will operated as required to heat a structure and offer hot water for showers, sinks as well as other hot water appliances around the house. And when it gets to the warm season or summer months, the combi boiler will only work when there’s a need for domestic hot water which also helps you save more money.

Combi boilers are able to provide domestic hot water in such a way that’s energy efficient due to two primary reasons - the combi units possess a very high operating efficiency and also have a low internal water volume. As a result, in during the hot summer when space heating is not required, you’ll only have to pay to heat up the hot water that you really need and not an entire tank.

Combi boilers also have the following benefits:

✓ Lower costs. Due to the combined nature of the boiler and the lack of tank in the roof space, the installation time and costs are at a minimum.

✓ Saves space in your home as it effectively combines a central heating boiler with a water heater into one unit.

Re-pressurising your boiler means that you allow more water to enter system via the filling loop. It can be easy to re-pressurise your boiler yourself. Always check your manual, but there are some simple steps you can take to restore pressure to your boiler:

1. Switch off your boiler and let it cool completely
2. Make sure both ends of your filling loop are attached
3. Open both valves to allow cold water into the system – you’ll hear it start to move
4. Look out for your pressure gauge to show 1.5 bar
5. Close both valves
6. Switch your boiler back on
7. Undo both ends of your filling loop and remove it. Remember some water might come out, so be ready to catch some spillage!

No. You must never repair your own boiler – only a Gas Safe-registered engineer can do any work on your boiler. You can do simple DIY tasks to repressurise your boiler or stop a leak, but if you have to remove the outer casing of the boiler or touch the flue then you must get a qualified boiler engineer to take a look at your central heating system.

Do British Gas Service Oil Boilers?

Are you interested in finding out whether or not the British Gas service oil boilers? Well, you’ll find the answer in this article! The British Gas engineers are able to repair several types of boilers such as home based combi, conventional as well as system boilers. Unfortunately, they do not fix oil boilers, electric boilers or solid fuel boilers, but if you possess a gas boiler that’s more than 70kW which is mostly present in commercial premises or large buildings you can give them a call.

For a yearly boiler service British Gas engineers will provide the following solutions to ensure central heating and boiler are both in proper working condition and also absolutely safe.

• Inspection of your boiler for possible leaks and corrosion.

• Detach your boiler casing to ascertain the proper functioning of it’s main components.

• Clean up all parts as necessary

• Attach the casing back to the system and make sure its well sealed

• Inspect the level of the gas pressure to ensure that it’s at the right level.

• Perform a flue check to determine that the are no toxic gas emissions like carbon monoxide being discharged by your heating system.

Upon completion of the annual boiler service, the British Gas qualified engineers will then drop a checklist with you which is going to include all the relevant information you may want to know about your boiler system.

In some cases, British Gas engineers may be able to complete the entire boiler service in one visit. However, it all depends on the problem that’s discovered (if any). They may not possess the required part to fix the problem with them, so they’ll have to order it from the British Gas national distribution centre. Most times, this part will get to them the next day so they can finish their tasks as soon as possible.

Your LPG storage tank will need to go outside your property, possibly underground if you have limited space. There are planning rules that restrict where you can put your tank, especially if your property is listed or on designated land. Take a look at our planning permission article to find out more.

When it comes to gas boilers, this is one of the most frequent questions that always pops up and for a good reason. When you invest a considerable amount of money to acquire and install a gas boiler in your home or property, it’s only reasonable not only to expect the boiler to warm up your home efficiently, but also to do so for a long period of time. If you’ve just bought or about to get a new gas boiler, it’s likely you won’t have to worry about getting a replacement for a lengthy period of time. Several gas boilers will last for anywhere between 10 to 15 years on the average. However in the event whereby you have an existing one that’s fast approaching the end of it’s useful life, then you should know the time go get a new gas boiler is just around the corner, and the earlier you make the purchase, the better (to avoid any surprise breakdowns that’ll leave your home super uncomfortable).

Just like any other home appliance, it’s a fact that an older gas boiler ( especially those that have been installed over a decade ago) are significantly less efficient that the new modern ones. When the older versions were manufactured is a completely different time to now as both technology and climate concerns are wide apart. So when your existing boiler is approaching the end of it’s useful life, it’ll be wise to start saving up to cover the cost of getting a new one. However, if it’s only about 5 years ago your boiler was installed, it’s highly likely to still be very efficient.

How To Get A Gas Fireplace Installed

A gas fireplace is one of the most popular means of adding warmth to homes which so many homeowners have now come to terms with, especially with natural gas prices being fairly low for an extended period of time. Properly installed gas fireplaces are not only capable of adding a much needed ambiance and warmth to your home, but also significantly more efficient than the traditional wood-burning fireplaces which mostly produces less heat from the large amount of drafts they consume. Meanwhile a good gas powered fireplace with a properly functioning blower, is very close to being as efficient as a furnace when warming up a room. What’s more? Gas fireplaces also possess a great visual appeal and are also very practical especially when they feature realistic ceramic logs as well as good gas burners.

Installing a gas fireplace by yourself is definitely up there as one of the most advanced DIY tasks you can attempt to try. If you lack proper training and experience, it’s advisable you leave the task to a reliable professional that’ll guarantee the best results while also ensuring costly errors are avoided. This guide will, however, put you in the right direction.

• Construct wall recess to accept the fireplace.

• Punch a hole through the exterior wall of the house to fit in stovepipe thimble.

• Fix a small part of the stovepipe to the exhaust port in the fireplace’s rear.

• Use construction adhesives on the wall around the fireplace opening’s sides and top.

• Apply granite slabs into the adhesive around the opening of the fireplace.

• Put the fireplace in position and ensure the stovepipe goes outdoors through the thimble.

• Use a termination hood to seal the exhaust pipe’s exterior.

• Employ the services of a professional plumber to connect the gas to the fireplace.

• Fit the removable front

• Test the functionality of the fireplace.

Does Home Insurance Cover Boiler Repairs?

When winter comes, your boiler is most likely to be one of the most used appliances in your home. It keeps operating for several hours to ensure your house remains warm and conducive and then during those cold evenings, it supplies the much needed hot water to guarantee a restive night. But with so much usage and many moving parts, you’d naturally expect your boiler to breakdown at some point especially if it’s 7 years old or above. So what’s the next line of action when it happens, leaving your radiators off and water cold? With the likely high boiler repair cost, it’s only logical to consider whether your boiler repairs is covered by your home insurance.

In almost all situations, the standard home insurance will not provide coverage for the cost of repairing or replacing a broken boiler. Being fully aware that boiler breakdowns are mostly caused by a lack or not so regular maintenance practices or servicing, most home insurance providers will exclude it from this from their offerings. In fact, a home insurance is more likely to provide coverage for the damage that has happened as a result of a broken appliance. For instance, the damage caused as a result of gas, oil or water leaking from a boiler are more likely to be paid for by the home insurance providers, but they’ll not pay for the repair or replacement of the broken boiler itself.

If you need our home insurance to cover your boiler repair, then you might just be able to get an extra insurance cover from your provider that includes a broken boiler repair. You can consult them to determine if this is possible as well as the cost to be paid per month. This will normally cost about £5 to £10 per month, but it gives you a peace of mind knowing you’re covered if your boiler happens to breakdown.