Find a Handyman you can trust in Haverhill.

There are a bunch of things a handyman can do around the house, so if you’re looking for a reason to hire one, you’d definitely find plenty. First and foremost, a handyman is basically a well versed, skilled and experienced professional who possesses the ability to carry out a plethora of tasks as well as repairs. While not all local authorities require handymen to have a license or carry an insurance policy, some handymen do have insurance. Generally, their rates vary based on their experience as well as specialities.

Handymen are able to handle a multitude of potential jobs in and around the house. These ranges from small tasks, installations, assembly, indoor or outdoor building or repair jobs. They are available to help out with a wide array of odd jobs around the home at a very reasonable price. So, what are some of the jobs a handyman can do in a home? Let’s take a look!

• Odd jobs. This encapsulates any small job you’d want done around the house. It could be a repair, installation or maintenance task.
• Gutter cleaning and repair. The idea of cleaning a gutter may seem hassle free, but there can be a couple of difficulties which includes the use of ladders and the risk of falling. When you hire a handyman to do this task, he does not only clean but also check for any damage or repair needs and much more.
• Painting. If you’re not able to handle some of your painting projects or perhaps you’re just not confident of how its going to turn out, it may be in your best interest to reach out to a skilled handyman.
• General carpentry and home repairs, these includes shelving, cabinets, bookcases, baseboards, framing, doors, countertops, moulding and more.

If you’re planning to acquire Sharps fitted wardrobes, one of the first few things that comes to mind is the cost to make such an acquisition. Generally, prices of these items can vary significantly. However, you should note that the more affordable end of the spectrum is most likely going to be around £750 to £900 per lineal metre, while mid range Sharps fitted wardrobes are usually within the range of £1400 to about £1600 per lineal metre. And finally, the high end customized Sharps fitted wardrobe are possibly going to be within the range of £3000 to £3500 per lineal metre.

The price of the Sharps fitted wardrobes is mainly determined by the fitted wardrobe solution your opt for. So let’s look at the estimated price range of Sharps fitted wardrobes depending on the styles you want for your home or property.

✓ There are the stylish, mordern sliding doors Sharps fitted wardron=be with mirrors that’ll make your room feel a lot bigger. If the type you opt for possesses three sections, then you’ll should expect to pay a price within the range of £2800 to about £3600 to have it fitted depending on the size of the room as well as the chosen finishes.

✓ Handcrafted, bespoke fitted bedroom wardrobe. This will cost about £2500 to £2900 with simple design details but the price can increase with ornate features like mouldings etc.

✓ Large bedroom 3m 80ccm three sections six door. This normally features finishes on both the interior and exterior as well as hanging space for clothes. It’s usually around £4900 or more.

✓ Simple two section closet. The price of this fitted wardrobe is usually within the range of £3200 to about £3500, but it could also be more depending on the design details you wish to implement.

1. How to build a shed base out of paving slabs
   • Mix sand and cement together to make mortar or use a pre-mixed one
   • Use a trowel to lay mortar for 1 slab at a time on the sub-base and lift a damp-sided slab onto the mortar, using a piece of timber and club hammer to tap the slab into position carefully. Continue to lay the first row of slabs
   • Make equally-sized spacers in all the joints in the slabs to ensure they’re the same size, checking it’s level as you go along
   • Next lay slabs along the two adjacent outer edges, filling in the central area row by row
   • Leave the mortar to set according to the instructions or for at least 48 hours before filling in the joints with mortar or paving grout
2. Building a shed base from concrete
   • Create a wooden frame around your shed base area (also called formwork) to stop the concrete from spreading
   • Mix pre-mixed concrete with water or use 1 part cement to 5 parts ballast
   • Wet the sub-base using a watering can with a rose on the end
   • Pour the concrete onto the framed base starting in one corner
   • Push the blade of a shovel up and down in the edges of the concrete to get rid of air bubbles
   • Use a rake to spread the concrete, leaving it around 18mm higher than the top of the frame. Work in sections of around 1-1.m²
   • Compact the concrete using a straight piece of timber that’s longer than the width of the base. Move the timber along the site, hitting it along at about half of its thickness at a time until the surface is evenly ridged
   • Remove excess concrete and level the surface by sliding the timber back and forwards from the edge that you started. Fill in any depressions and repeat until even
   • Run an edging trowel along the frame to round off exposed edges of the concrete and prevent chipping
   • Cover the concrete with a plastic sheet raised on wooden supports to allow slow drying. Weigh it down with bricks
   • Once the concrete is set, you can install your shed and remove the wooden frame with a crowbar

You should pull up and remove weeds by hand as and when they appear. If it is a regular problem, you might need to reseal the paving. In extreme cases, the sub layer itself may need to be re-laid. You can use weed killer, however some paving can be discoloured by stronger weed killers.

1. Remove any existing fascia boards Remove the fascia boards and the old felt if you’re re-felting.
2. Measure the shed roof Measure the roof, taking into account that you should leave around 50mm for overlaps at the eaves and 75mm at the gable ends. You’ll probably need 3 pieces of felt, but some smaller sheds only need 2.
3. Apply felt to the roof Once you’ve cut the felt to size, apply the each piece to the roof, pulling it tight. Then nail along the length of the roof at 100mm intervals. For nails at the bottom edge, they can be wider – around 300mm. If you’re adding a piece of felt in the middle of the shed along the apex, fix it using adhesive, then nail it at the lower edge at 50mm intervals.
4. Tidy up the overhangs Fold down the felt at each overhang and nail it securely. Cut a slit in the overhang at the apex using a pen knife, then fold that down and nail at 100mm intervals along the gable. If you like, you can add fascia boards to keep the shed looking neat. Use wood nails to secure them and then trim away any excess felt.

How To Clean Roof Tiles?

If you’re a DIY person with a dirty roof tiles or just a homeowner who’s also a lover of knowledge, you may probably like to know how you can have your roof tiles cleaned. This is a very common question which often depends on the dirt or debris you’re dealing with as well as the type of roof you possess. Most often than not, if you own a traditional concrete or slate roof tiles, then you’re more likely to battle moss and or algae growth.

If you’re not a competent DIY person or do not have enough confidence to pull this off, then it’s advisable to hire the services of a professional who can guarantee the best results for help. In this article, you’ll learn how to go about cleaning your roof tiles. Let’s have a look!

✓ Consider Safety. When it comes to roof cleaning, you have to be very careful. They’re normally high up and any task that deals with height will usually require putting safety measures in place. Firstly, it’s important to be confident with heights and ladders, if not you’d have to find someone who is. And if you’re confident, there’s also the need to find someone who can help you hold the base of the ladder.

✓ Trim the trees. Nearby trees are usually a threat to any roof and also makes cleaning much harder. So it’s always wise to cut any overhanging branches before you proceed.

✓ Bleach or not to bleach. Although you have to be very careful using beach and water but it also happens to be one of the easiest DIY ways to clean your roof. You either stand about 4 feet away and rely on water pressure or clean down the tiles by hand.

✓ Try not to make use of a blaster.

First and foremost, a conservatory or a sunroom is a structure attached to the sunny part of a house which possess glass walls and roof which enables the sun’s entrance into the space. Conservatories happen to be a very popular structure in the UK as home and property owners are able to subject it to wide variety of uses such for relaxation, entertainment, hangouts with family and friends, reading and lots more. Therefore, when the conservatory roof is leaking a lot of activities could be affected. Hence, the more reason why you should know hoe to repair this kind of issue by yourself. However, if you’re not confident enough to carry out this task, we’ll recommend you call in a professional who can guarantee the best output the first time. In this guide, we’re going to look at the conservatory roof leak repair process.

• Spot the leak. The first line of action is to examine the conservatory’s roof to identify the leaking part (tip - most leaks takes place around transparent roof panes edges). If you have a slanted roof, you’d have to look carefully. The spot where it drips may not necessary imply that its the leaking spot.
• Remove the old seal. Climb a ladder to access the leaking pane. Then, with the help of a utility knife, lift out the panel and clean all traces of the old sealant. Once done, simply lay down a bead of the new sealant in the frame, press the clear panel back in place and apply sealant to the outer edges.
• Cracked pane. If the existing pane is cracked or broken, simply hold the pieces tightly together by applying tape across the pane in various directions
• Leak sealing. Another option to fix leaks is by applying a sealant around the leaking pane without having to remove it.