Find a Gutter Installer you can trust in Arisaig.

Knowing when best to clean your gutters can do a lot of good. Wile some people assume that fall is the best time for gutter cleaning after the leaves fall, others believe spring is the most appropriate time to clean the gutters before things start to grow there. The truth is, both camps are right. However, the best time to clean your gutters depend on a wide range of factors which are all unique to you. In order to help you make the most informed decision possible, we have created this post to help you figure out the right time to clean your gutters. Let’s take a look!

Where you’re located. What we get is four season in a year as well as as a good amount of rain. As a result, you may want to put into consideration cleaning your gutter at least twice a year - clean the gutters once in the spring and once in the fall. It’s important to make gutter cleaning a part of your normal spring schedule as well as part of your fall maintenance routines.

What surrounds your home. If you happen to have tree surrounding your home, then it’s more likely that dead leaves clog up your gutter pretty quickly. A single tree is enough as it’s going to shed leaves that will find their way into your gutter, accumulate and affect its performance and integrity.

What your gutter currently looks like. If you gutters already have an entire ecosystem of animal life and plants hamging over the edges, then the best time to clean the gutters is now rather than having to wait a particular season to act. A dirty gutter should be attended to immediately in order to prevent some unnecessary damages as well as expensive repairs.

You don’t always need scaffolding to replace guttering. If your home is a bungalow, the tradespeople might only need a ladder to replace your guttering. It’s when your home is two storeys or more that scaffolding is more necessary.

You might not need full scaffolding for a simple two-storey home. Guttering specialists use scaffold towers, which are the platforms you see underneath the scaffolding, where the installation is relatively straightforward. You might need scaffolding to replace guttering when there are obstructions to towers being used – for example, if you have a conservatory or the ground is very uneven. It's more likely that specialist roofline companies will use scaffold towers when necessary. Sole traders that replace guttering as part of their services may be comfortable using sturdy ladders.

There’s no legal requirement to say that you must have scaffolding when fitting guttering, but it is a good idea when working on homes rather than bungalows. If you’re unsure whether you need full scaffolding for your gutter replacement project, get a few quotes from reputable businesses of different sizes. If you’ve been quoted by one company that you need full scaffolding whereas everyone else says that only towers are needed, it’s likely that the job is perfectly safe to carry out with just towers.

Soffits are constructed by homeowners on their properties for several purposes. Not only are they incorporated to hide away the unsightly features of a home, but they can also be used to add decorative architectural detail. Soffits construction, on the other hand, is a project that can be done by any DIY person with the knowledge and experience. However, if you lack the confidence to pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the best results, the first time. In this guide, we’re are going to take you through the soffit construction process.

✓ Measure and mark. The first step is to take an accurate measurement of the size of your propose soffit and use a pencil to mark it out on both the wall and ceiling. The size of your soffits is mainly determined by your needs or preferences.

✓ Cut and Install Wall & Ceiling Plates. Proceed to cut the wall as well as ceiling plates once the dimensions have been marked. Make use of 2x4 lumber, you can cut to size with the help of a table saw or mitre. Once done, you can then attach it to the wall as well as ceiling studs with a framing nail gun.

✓ Build the box frame. Develop a box-frame from 2x4 lumber, using your measurements as guide.

✓ Fit the box frame. Hold the box frame in place with some slide clamps and then attach it to the ceiling and wall plates with drywall screws.

✓ Mark the studs. Make use of a pencil to mark out the studs location on your soffit box frame.

✓ Cut and hang the drywall. Cut the drywall with a utility knife uing your measurement as a guide. Once done, attach the drywall to the framework with the help of drywall screws.

✓ Add finishing touches. This includes installing the corner beads, finishing off with the common drywall work of taping, spackling and sanding. Once the spackle is dry, you can the complete it by painting the soffit.

You should replace your soffits and fascias if you are having problems. Soffits and fascias can degrade and rot away over time, and this can cause leaks, faulty guttering, or even allow pests entry to the roof space. If any of these problems occur, you should speak to an experienced roofline company to discuss replacing your soffits and fascias.

1. Hang a plumb bob from the outlet to the drain to use as a guide while you draw several marks on the wall with a pencil to show you where the downpipe will run.
2. Join the marks up with a straight edge, creating a line to show where the centre of the downpipe will be.
3. Position a downpipe clip at the top of wall, in the centre of the pencil line. Mark the position of its fixing holes on the wall. If you need an offset bend, put a downpipe clip directly below the bend.
4. Repeat the process down the wall. Make sure there is no more than 1.8 metres between pipe clips.
5. Refer to the guttering manufacturer’s instructions to see which drill bit is required. Use a drill to drill the fixing holes and insert wall plugs.
6. Fit the first piece of downpipe starting from the outlet and moving towards the drain.
7. If you need to add more downpipe, join the two pieces with a pipe socket and clip. Leave a 10mm gap between the end of the pipe and the bottom of the pipe socket, because it will probably expand. Then attach a pipe clip over the joint.
8. Continue attaching pipe clips down the length of the downpipe.
9. If you need to, fit a downpipe show to direct the water into the drain. Attach a downpipe clip directly below the socket of the shoe.

Soffits and fascias sit along the sides of your property, over the join between your walls and your roof. The fascia attaches to the end of your roof rafters, hiding and protecting them. The soffit fixes on the bottom of the fascia, bridging the gap between your fascia and wall. Your guttering attaches to the fascia, which also joins to the bargeboard on your gable end, if you have one.

It can be a huge headache, but cleaning of gutters is a task that needs to be done and even more so when it’s a stained white gutter. Nobody want to do it, but everybody has to. If you happen to lack the required confidence to pull this off as it has to do with working at heights, then we’d strongly recommend that you get in touch with a reliable professional who can guarantee the best results for help and also save you some time and money from potential costly errors. In this post, we’re going to show you some of effective way in which you can tackle stained white gutters effectively.

Firstly, you’ll have to take out the ladder with a pair of rubber gloves. Simply position the ladder safely, climb up the roof and start removing the leaves and other debris clogging up the gutters. You can also make use of a garden trowel to remove the very thick debris. Once done, spray the gutter using a garden hose to flush out the dirt as this will make the stains visible. Then prior to cleaning, ensure to cover the plants or landscape underneath with tarp or plastic sheet since the cleaning solution may negatively impact the vegetation.

Start to clean by spraying an all-purpose cleaner on the stains and srub them off using a scrub brush. You can also try a mixture of 1/4 of water with 1 cup of bleach and 1 teaspoon of dish soap. Dip your scrub brush in this solution to scrub off the stains. The bleach mixture is guaranteed to eliminate any mold or mildew that growing on your gutters with ease.

In the UK, gutters are normally made from uPVC. It’s a hardy plastic that won’t rot, warp or tarnish very easily, which is why it’s so popular. It’s the same material that’s used for most homes’ windows these days; they don’t have to be the standard white as they can be made into a range of colours. Expect to pay an average of £500 for the supply and installation of uPVC guttering, and more if you require scaffolding.

Other materials that are popular for gutters include copper, aluminium and cast iron. These are much more expensive – you might be looking at around £1500 or more for the supply and installation – but they give a more polished look and are often used on period properties or those in a conservation area. If you're considering these types of gutters, make sure you get a few quotes from different roofline companies so you can compare the different materials.

In the past, gutters were made from wood, asbestos concrete or stone. They were often lined with lead to stop the water from seeping through. When it was discovered that asbestos was seriously harmful, it of course stopped being used. Wood was prone to rotting, even with lead lining, and stone is heavy and expensive. So when uPVC came along, it became an affordable and easy material to use for gutters so homeowners could be confident that rainwater will be kept away from the foundations of their properties. It’s important to keep gutters clear from leaves and debris, because if they become blocked, they can make water to fall against your property’s walls, causing damp.