Find a Gutter Installer you can trust in Bodorgan.

Fascias and Soffits, just like any other components of a home, do not last forever. They can become tired and worn out over time which implies that you’ll have to replace them to prevent further damage. Getting this project completed can be quite costly, but it doesn’t have to be. Fitting soffits and fascias is very simple task which will leave you with both a modern and contemporary styling which requires little maintenance and also more savings. What’s more? You don’t have to worry about repainting the fascias and soffits on an annual basis, all you need to do is a gentle wipe down of the features with a damp cloth to have them look good.

If you’re a competent DIYer and confident enough to pull off this task, then all the better. However, if otherwise, we’d strongly recommend you hire the services of a reliable contractor who can guarantee the best results for help. Here are the steps you can follow to fit your fascias and soffits.

Fascias ( a 18mm fascia board)

✓ This is designed for a direct fix without a need for a timber substrate. Simply secure them directly to the rafters with the help of 2 x 65mm a4 stainless steel fixing nails per rafter.

✓ Ensure that the rafters are level.

✓ Cut the boards back 5mm per edge to enable expansion where any white corner trims, joint trims or angle trims is needed.

✓ Secure the guttering to all third rafter.

Soffit ( 9mm soffit board)

✓ Ensure that the preservative treatment to the structural timber has dried out.

✓ Fix all utility boards of about 100mm to 605mm in width at a maximum of 60mm centres.

✓ If ventilation is needed, there are some soffits that are available in 150mm to 605mm widths and also provides the 10mm air gap needed for roof with a pitch above 15 degrees

In the UK, gutters are normally made from uPVC. It’s a hardy plastic that won’t rot, warp or tarnish very easily, which is why it’s so popular. It’s the same material that’s used for most homes’ windows these days; they don’t have to be the standard white as they can be made into a range of colours. Expect to pay an average of £500 for the supply and installation of uPVC guttering, and more if you require scaffolding.

Other materials that are popular for gutters include copper, aluminium and cast iron. These are much more expensive – you might be looking at around £1500 or more for the supply and installation – but they give a more polished look and are often used on period properties or those in a conservation area. If you're considering these types of gutters, make sure you get a few quotes from different roofline companies so you can compare the different materials.

In the past, gutters were made from wood, asbestos concrete or stone. They were often lined with lead to stop the water from seeping through. When it was discovered that asbestos was seriously harmful, it of course stopped being used. Wood was prone to rotting, even with lead lining, and stone is heavy and expensive. So when uPVC came along, it became an affordable and easy material to use for gutters so homeowners could be confident that rainwater will be kept away from the foundations of their properties. It’s important to keep gutters clear from leaves and debris, because if they become blocked, they can make water to fall against your property’s walls, causing damp.

Soffits and fascias are available in lots of different colours. These include black, grey, brown, white and cream. It’s also possible to get them in brighter colours like reds, blues and greens.

What colour soffits and fascias you get is entirely up to you, unless you live in a listed building, in which case some rules may apply. Most people choose a colour that matches their roof, walls or window frames to give their property an attractive, colour-coordinated look.

• A sturdy ladder
• Gloves and safety goggles
• A hammer and nails to secure your fascia so it doesn’t fall down mid-replacement
• A hacksaw – this will cut through uPVC guttering – just make sure you leave a margin of error with every cut you make
• Cable ties or rope to secure the existing gutters while you dismantle them, so they don’t fall off
• All the right fixings and brackets to secure the guttering
• An electric drill and/or screwdrivers

1. Add a gutter bracket to the top of the fascia board at the opposite end to the stop-end outlet, if you have one. Then tie a piece of string around the base of the bracket.
2. You’ll need to place the gutter outlet accurately over the drain. Hold a plumb line against the fascia directly over the drain, and mark that position with a pencil. Following the manufacturer’s advice on the number of screws to use, fit the gutter outlet no more than 50mm below the level of the roof tiles.
3. Stretch the piece of string you tied on the bracket along the fascia board, and tie it to the outlet. Make sure you check with a spirit level that the string slopes towards the outlet.
4. Mark the positions of the other brackets. They should be no more than 800mm apart, or 600mm if your roof is very steep. They also shouldn’t be any more than 150mm from a joint or fitting. Then fit the rest of the brackets.
5. Fit a stop-end to the first length of gutter and clip it into position on the brackets. At the other end, fit a union piece and screw it into the fascia.
6. Then fit the next length of gutter into it, and the next until you’re finished. Cut the last one to fit using your hacksaw before attaching a stop-end. Then make sure all the joints line up with the insertion depth marks on the fittings. Then you’re done!

Having ventilation in the roof void is a requirement for building regulations approval. Fitting ventilated soffits is the typical way that this roof ventilation is achieved. If you do not have roof ventilation, you may find that your roof void has problems with condensation or overheating.

Leaves, twigs and moss all have one thing in common which often annoys home and property owners - they are the three main materials that negatively impacts the proper functioning of a roof guttering system. The major cause of water drainage problems for most homes and buildings are these organic materials. Wondering how some leaves and few twigs can cause such a big problem? Over time there’ll be a gradual build up of the natural debris in your gutter system which starts to rot and turn  to a thick and muddy goo which obstructs the flow of water in your drainage. As a result, there’s the need to make sure that your gutters are thoroughly cleaned at least twice annually in order to prevent bigger issues that can be caused by the blockage of a drainage system.

So if you’re considering getting your gutters cleaned by a professional, you’d probably be interested in know just how it’s going to cost. Well, there’s not straightforward and simple answer to this question as there are a number of factors that contributes to the final cleaning cost of your gutters.

In general, in the UK, the average cost for cleaning of gutter is usually around £18 to about £25 per hour. However, you can also be quoted a day rate which is usually ranging between £150 to £200 per day.

The factors that can affect gutter cleaning price includes the type of your property (such as a terraced, end of terraced, detached and semi detached homes) which possesses a varying gutter cleaning price largely due to their size differences, the height of the building ( if you require the service for a property located on the second floor of a building, this would be a bit higher than if it were to be on the ground floor) as well as additional requests.

As long as you can access them safely, it’s fairly easy to clean soffits and fascias. Using a sponge and warm water to scrub them is a good way to get off most types of dirt. You might want to add detergent or bleach to the water to make it more effective.

Once you’ve scrubbed your soffits and fascias, rinse them with clean water to make sure you’ve got all of the dirt and detergent off.

Yes, it’s a dirty job, but every homeowner out there has got to do it! Your gutter needs to be free of dead leaves, birds’ nest and other debris as well as being through clean in order to perform its functions effectively. It’s just a part of the responsibilities that comes with owning a home. Dry leaves, tree branches and other materials build up in your gutters overtime especially during the dry summer and you won’t notice until the point where your gutters start overflowing during the first main rain of the season.

In the event whereby your dirty and clogged gutter is left unattended to, this can lead to several issues like a leaky gutter and mold, leaky roof and basements,cracked foundation, driveway and yard damage and several more which will definitely make you incur more unnecessary expenses. So the question is, how often should the gutters be cleaned? The answer is, it depends. According to several experts, gutters should be cleaned at least twice a year - which is once in the late spring and once in the late summer or early fall. However, there are a couple of factors that may make you have a rethink.

If you happen to have a pine tree growing above your house, it’ll be wise to consider inspecting your gutters every 3 months. This is because pine trees shed needles year-round and they usually have a lot of these needles to shed. In the situation whereby you’re located at a higher elevation, ice is will most likely be your greatest source of concern. Making sure that your gutters remain clean throughout the winter can be quite a headache, but damage to your roof cause by ice can be an even greater pain. Prevention is always better than cure.