Find a Gutter Installer you can trust in Pembroke Dock.

You can paint your soffits and fascias if they’re made of wood. In fact, it’s a good idea to do this every few years, as it can help to preserve them and keep them looking smart.

You can choose what you paint your soffits and fascias with by deciding what kind of look you want to achieve. You can stain them if you want to maintain a natural wood look, or use an exterior gloss or satin paint if you want to change their colour.

• A sturdy ladder
• Gloves and safety goggles
• A hammer and nails to secure your fascia so it doesn’t fall down mid-replacement
• A hacksaw – this will cut through uPVC guttering – just make sure you leave a margin of error with every cut you make
• Cable ties or rope to secure the existing gutters while you dismantle them, so they don’t fall off
• All the right fixings and brackets to secure the guttering
• An electric drill and/or screwdrivers

1. Add a gutter bracket to the top of the fascia board at the opposite end to the stop-end outlet, if you have one. Then tie a piece of string around the base of the bracket.
2. You’ll need to place the gutter outlet accurately over the drain. Hold a plumb line against the fascia directly over the drain, and mark that position with a pencil. Following the manufacturer’s advice on the number of screws to use, fit the gutter outlet no more than 50mm below the level of the roof tiles.
3. Stretch the piece of string you tied on the bracket along the fascia board, and tie it to the outlet. Make sure you check with a spirit level that the string slopes towards the outlet.
4. Mark the positions of the other brackets. They should be no more than 800mm apart, or 600mm if your roof is very steep. They also shouldn’t be any more than 150mm from a joint or fitting. Then fit the rest of the brackets.
5. Fit a stop-end to the first length of gutter and clip it into position on the brackets. At the other end, fit a union piece and screw it into the fascia.
6. Then fit the next length of gutter into it, and the next until you’re finished. Cut the last one to fit using your hacksaw before attaching a stop-end. Then make sure all the joints line up with the insertion depth marks on the fittings. Then you’re done!

As long as you can access them safely, it’s fairly easy to clean soffits and fascias. Using a sponge and warm water to scrub them is a good way to get off most types of dirt. You might want to add detergent or bleach to the water to make it more effective.

Once you’ve scrubbed your soffits and fascias, rinse them with clean water to make sure you’ve got all of the dirt and detergent off.

You don’t always need to replace your gutters with your roof. Often people think that it’s a requirement, or simply the best thing to do, but it’s not always necessary. The reason why people think it’s required is because to re-roof a home, the guttering often needs to be removed and put back on.

If the time has come to replace your roof, then the chances are that your guttering is pretty old too. When you start to get quotes for your roof replacement, ask the roofer to take a look at your guttering as well. If there are signs of peeling, rust, cracks or sagging, then it makes sense to replace your gutters with your roof. If you get them done at the same time, you’ll save money labour costs, which is the reason why most homeowners do it.

Another reason to replace your gutters with your roof is the risk of damage. Re-roofing is a significant project, so the guttering needs to come off most of the time – running the risk of brackets and pipes getting damaged in the process. So if your guttering is still looking good right now but you think it might need replacing in a couple of years, it might be worth just doing it at the same time as your roof to save you money and the stress if damage does occur.

However, if your guttering has only recently been replaced, then there’s no need to replace it again with your roof. But because it needs to come off, make sure you speak to the roofing company about keeping it safe and doing their best to avoid damage. It’s also worse ensuring that they have the correct insurance to cover you both in case your guttering does get damaged during your roof replacement.

Keeping water away from your house is of great importance and hence, the installation of a roof guttering system to serve this purpose. However, in order to perform this task effectively and seamlessly, there’s a need to clear out the clogging dirt and debris from the gutter and ensure it’s free from water-blocking obstacles at all times. Although there are a number of ways to achieve this, but the major cause of concern for several home and property owners is having to work at heights or on top of a ladder to get the job done. This is a very dangerous endeavour especially if you do not have the confidence required to pull it off. As a result, we’d strongly recommend you hire the services of a reliable professional who possess the skills when it comes to working at heights and delivering a highly effective clean. Fortunately, there are a couple of ways you can get to clean your gutters without having to climb any ladders. Let’s take a look!

• Clean the gutter with a leaf blower. Several leaf blowers feature a nozzle attachment which is made to release a narrow stream of air which is suitable for cleaning of gutters. You don’t need a ladder to do the clean as a specialized attachment is available in order to increase the blower’s reach to your roof effortlessly. The final step would be to remove any lingering leaves or twigs using a hose.
• Clean the gutter with a wet or dry vacuum. For heavier debris, you can try out a wet or dry vacuum. To reach the obstructed gutters while standing on the ground, simply get curved attachments and hoses at a local home improvement store. You may, however, need to moisten some stubborn dirt before it can be properly vacuumed or removed.after completing the vacuuming process, simply flush the gutters with garden hose waters.

It may be shocking a whole lot of people would not be able to point out fascias and soffits on a building despite the fact that they’re an essential part of the roof. To give you an idea, they’re simply used to cover the roof beams’ ends that comes out of the wall from underneath of the roof. The board that runs vertically just below the roofline is the fascia board, which is also the long length of UPVC. Therefore if you look at the gutters located in the front of house, the board behind is called the fascia board. However, soffits runs horizontally from behind the gutters to the wall of a building, so if you walk close to a house and look up, you’ll identify the soffits. They’re done to cover the gaps between the wall house and the gutters. The main function of both soffit and fascia is to divert water away from your roof as well as walls.

Fascias and soffits were usually made of wood before UPVC came along. And as a result, they only require little maintenance, no more warping, painting or cracks unlike the wooden ones. However they also can’t last an eternity, so when the time comes and you need to replace your soffit and fascia, you’ll probably want to know just how much it’s going to cost.

Unfortunately, there’s no way to calculate an accurate cost for fascias and soffits as there are too many variables to put into consideration. These includes the type of fascia and soffit you choose as well as the size of your property. However the average cost to replace a three bed semi-detached house’s fascias and soffits is within the range of £1200 to £1500 or even more if you’re staying in London or in a larger detached building.

Soffit is a word gotten from two languages - French and Latin, whereby the root word implies to “form as a ceiling in French, while it means to “to fix underneath in Latin. Basically, soffit is a portion of the ceiling that has been constructed lower than the area that surrounds it. And even though they aren’t that much popular in recent times, they happen to be a common feature in kitchens of older homes in the UK. At times, a soffit can occupy the whole room or area in a home.

Homeowners across the globe make use of this feature mostly as a decorative element in the room , however, there are also times in which they may be required for various purposes. These purposes include using soffits to conceal plumbing pipes or, heating or cooling ducts, which is often the case when sofits are constructed at the lower levels of homes. They’re also often incorporated in bathrooms or kitchens as soffits house light fixtures. For instance, recessed light fixtures fitted over kitchen or bathroom sinks are mostly fitted into a soffit. What’s more? Soffit can also be required in a room because of the home’s structure as the feature can be used to hide a structural beam.

If you happen to own an older home and you’d like to remove an existing soffit, the first step is to ensure that its safe to carry out such plan. You should firstly check for any electrical lines, ductwork, lighting or structural problems that may exist prior to the commencement of the project. If you’re not sure or confident enough to pull this off, then it’s advisable to consult a professional contractor before you proceed.

1. Hang a plumb bob from the outlet to the drain to use as a guide while you draw several marks on the wall with a pencil to show you where the downpipe will run.
2. Join the marks up with a straight edge, creating a line to show where the centre of the downpipe will be.
3. Position a downpipe clip at the top of wall, in the centre of the pencil line. Mark the position of its fixing holes on the wall. If you need an offset bend, put a downpipe clip directly below the bend.
4. Repeat the process down the wall. Make sure there is no more than 1.8 metres between pipe clips.
5. Refer to the guttering manufacturer’s instructions to see which drill bit is required. Use a drill to drill the fixing holes and insert wall plugs.
6. Fit the first piece of downpipe starting from the outlet and moving towards the drain.
7. If you need to add more downpipe, join the two pieces with a pipe socket and clip. Leave a 10mm gap between the end of the pipe and the bottom of the pipe socket, because it will probably expand. Then attach a pipe clip over the joint.
8. Continue attaching pipe clips down the length of the downpipe.
9. If you need to, fit a downpipe show to direct the water into the drain. Attach a downpipe clip directly below the socket of the shoe.