Find a Gutter Installer you can trust in Clynderwen.

You don’t always need scaffolding to replace guttering. If your home is a bungalow, the tradespeople might only need a ladder to replace your guttering. It’s when your home is two storeys or more that scaffolding is more necessary.

You might not need full scaffolding for a simple two-storey home. Guttering specialists use scaffold towers, which are the platforms you see underneath the scaffolding, where the installation is relatively straightforward. You might need scaffolding to replace guttering when there are obstructions to towers being used – for example, if you have a conservatory or the ground is very uneven. It's more likely that specialist roofline companies will use scaffold towers when necessary. Sole traders that replace guttering as part of their services may be comfortable using sturdy ladders.

There’s no legal requirement to say that you must have scaffolding when fitting guttering, but it is a good idea when working on homes rather than bungalows. If you’re unsure whether you need full scaffolding for your gutter replacement project, get a few quotes from reputable businesses of different sizes. If you’ve been quoted by one company that you need full scaffolding whereas everyone else says that only towers are needed, it’s likely that the job is perfectly safe to carry out with just towers.

Soffits are constructed by homeowners on their properties for several purposes. Not only are they incorporated to hide away the unsightly features of a home, but they can also be used to add decorative architectural detail. Soffits construction, on the other hand, is a project that can be done by any DIY person with the knowledge and experience. However, if you lack the confidence to pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the best results, the first time. In this guide, we’re are going to take you through the soffit construction process.

✓ Measure and mark. The first step is to take an accurate measurement of the size of your propose soffit and use a pencil to mark it out on both the wall and ceiling. The size of your soffits is mainly determined by your needs or preferences.

✓ Cut and Install Wall & Ceiling Plates. Proceed to cut the wall as well as ceiling plates once the dimensions have been marked. Make use of 2x4 lumber, you can cut to size with the help of a table saw or mitre. Once done, you can then attach it to the wall as well as ceiling studs with a framing nail gun.

✓ Build the box frame. Develop a box-frame from 2x4 lumber, using your measurements as guide.

✓ Fit the box frame. Hold the box frame in place with some slide clamps and then attach it to the ceiling and wall plates with drywall screws.

✓ Mark the studs. Make use of a pencil to mark out the studs location on your soffit box frame.

✓ Cut and hang the drywall. Cut the drywall with a utility knife uing your measurement as a guide. Once done, attach the drywall to the framework with the help of drywall screws.

✓ Add finishing touches. This includes installing the corner beads, finishing off with the common drywall work of taping, spackling and sanding. Once the spackle is dry, you can the complete it by painting the soffit.

Soffits and fascias sit along the sides of your property, over the join between your walls and your roof. The fascia attaches to the end of your roof rafters, hiding and protecting them. The soffit fixes on the bottom of the fascia, bridging the gap between your fascia and wall. Your guttering attaches to the fascia, which also joins to the bargeboard on your gable end, if you have one.

Knowing when best to clean your gutters can do a lot of good. Wile some people assume that fall is the best time for gutter cleaning after the leaves fall, others believe spring is the most appropriate time to clean the gutters before things start to grow there. The truth is, both camps are right. However, the best time to clean your gutters depend on a wide range of factors which are all unique to you. In order to help you make the most informed decision possible, we have created this post to help you figure out the right time to clean your gutters. Let’s take a look!

Where you’re located. What we get is four season in a year as well as as a good amount of rain. As a result, you may want to put into consideration cleaning your gutter at least twice a year - clean the gutters once in the spring and once in the fall. It’s important to make gutter cleaning a part of your normal spring schedule as well as part of your fall maintenance routines.

What surrounds your home. If you happen to have tree surrounding your home, then it’s more likely that dead leaves clog up your gutter pretty quickly. A single tree is enough as it’s going to shed leaves that will find their way into your gutter, accumulate and affect its performance and integrity.

What your gutter currently looks like. If you gutters already have an entire ecosystem of animal life and plants hamging over the edges, then the best time to clean the gutters is now rather than having to wait a particular season to act. A dirty gutter should be attended to immediately in order to prevent some unnecessary damages as well as expensive repairs.

1. Hang a plumb bob from the outlet to the drain to use as a guide while you draw several marks on the wall with a pencil to show you where the downpipe will run.
2. Join the marks up with a straight edge, creating a line to show where the centre of the downpipe will be.
3. Position a downpipe clip at the top of wall, in the centre of the pencil line. Mark the position of its fixing holes on the wall. If you need an offset bend, put a downpipe clip directly below the bend.
4. Repeat the process down the wall. Make sure there is no more than 1.8 metres between pipe clips.
5. Refer to the guttering manufacturer’s instructions to see which drill bit is required. Use a drill to drill the fixing holes and insert wall plugs.
6. Fit the first piece of downpipe starting from the outlet and moving towards the drain.
7. If you need to add more downpipe, join the two pieces with a pipe socket and clip. Leave a 10mm gap between the end of the pipe and the bottom of the pipe socket, because it will probably expand. Then attach a pipe clip over the joint.
8. Continue attaching pipe clips down the length of the downpipe.
9. If you need to, fit a downpipe show to direct the water into the drain. Attach a downpipe clip directly below the socket of the shoe.

If you live in an average home with an average amount of guttering and you’re used to a bit of DIY, it’s relatively easy to replace gutters. But if you have a home that’s more than two-storey or you have guttering that’s more complicated, it’s best left to the professionals.

Lots of homes these days have uPVC guttering. uPVC is a hard-wearing plastic that will last a long time without much maintenance except your usual gutter clearing. It’s relatively light, so lots of people think it’s easy to replace uPVC gutters. If you live in a bungalow, you may be able to just use a ladder to take down your old guttering and replace it with new uPVC gutters, but if you live in a two-storey home it can be a bit more complicated. If you do attempt to replace your gutters yourself, make sure you’ve got a sturdy ladder that will comfortably reach the right height, and never rest it on the fascia or the guttering itself.

If you have cast iron or copper guttering, this is much heavier and bulkier than uPVC. Certainly don’t try to replace these on your own – make sure you have another competent DIYer to help you. Reputable roofline specialists will use scaffold towers to make it easier to handle heavy gutters and they will always work in pairs on this type of guttering, so make sure you have the right tools and equipment to work with.

Just because it’s easy to replace gutters, it doesn’t mean you should. It’s better to ask a reliable roofline company to help you, since they have the skills to fit guttering properly and have experience with working at height.

To keep water away from your house, the importance of gutters cannot be overemphasized. However, in order to enable them do their job the proper way, the clogging dirt and debris must be thoroughly wiped out and fortunately there are a number of ways to get the job done by yourself. However, it must be stated that cleaning of gutters can be a very dangerous task as it deals with working at heights. As a result, if you are not confident enough to this pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the job effectively and also in a safe manner. In this guide, we’re going to look at some of the ways in which you get rid of dirt and debris on your gutter by yourself.

• Clean the gutter with a leaf blower. Several leaf blowers feature a nozzle attachment which is made to release a narrow stream of air which is suitable for cleaning of gutters. All you have to do is simply to position your ladder to enable you work slowly towards the downspout and getting rid of all dirt and obstructions on the gutter as you go. The final step would be to remove any lingering leaves or twigs using a hose. If don’t want to stand on a ladder to do all these, a specialized attachment is available to add to the blower’s reach.
• Clean the gutter with a wet or dry vacuum. For heavier debris, you can try out a wet or dry vacuum. To reach the obstructed gutters while standing on the ground, simply get curved attachments and hoses at a local home improvement store. You may, however, need to moisten some stubborn dirt before it can be properly vacuumed or removed.after completing the vacuuming process, simply flush the gutters with garden hose waters.