Find a Gutter Installer you can trust in Buckfastleigh.

Fascias and Soffits, just like any other components of a home, do not last forever. They can become tired and worn out over time which implies that you’ll have to replace them to prevent further damage. Getting this project completed can be quite costly, but it doesn’t have to be. Fitting soffits and fascias is very simple task which will leave you with both a modern and contemporary styling which requires little maintenance and also more savings. What’s more? You don’t have to worry about repainting the fascias and soffits on an annual basis, all you need to do is a gentle wipe down of the features with a damp cloth to have them look good.

If you’re a competent DIYer and confident enough to pull off this task, then all the better. However, if otherwise, we’d strongly recommend you hire the services of a reliable contractor who can guarantee the best results for help. Here are the steps you can follow to fit your fascias and soffits.

Fascias ( a 18mm fascia board)

✓ This is designed for a direct fix without a need for a timber substrate. Simply secure them directly to the rafters with the help of 2 x 65mm a4 stainless steel fixing nails per rafter.

✓ Ensure that the rafters are level.

✓ Cut the boards back 5mm per edge to enable expansion where any white corner trims, joint trims or angle trims is needed.

✓ Secure the guttering to all third rafter.

Soffit ( 9mm soffit board)

✓ Ensure that the preservative treatment to the structural timber has dried out.

✓ Fix all utility boards of about 100mm to 605mm in width at a maximum of 60mm centres.

✓ If ventilation is needed, there are some soffits that are available in 150mm to 605mm widths and also provides the 10mm air gap needed for roof with a pitch above 15 degrees

A gutter is part of the system that takes rainwater away from a building. Every home will have some form of guttering system to stop water from dripping off the roof and into the walls. It’s important to keep your gutters clear because if water starts to seep into your home’s walls, you’re likely to get damp.

A guttering system consists of half pipes, troughs, bends and downpipes. They’re usually cylindrical in shape but they may be square on some homes and in countries outside of the UK. Technically, the gutter is the part that you’ll see across your roof that collects rainwater. The water will then feed into a downpipe from your roof’s edge to the base of your home, where you can collect it in something like a water butt, or it will be discharged to a surface water drain or soakaway.

In early times, gutters used to be made from lined wood or stone. Lead was often used as the liner to stop rainwater from seeping through the material, but you won’t see it used much anymore. These days, most homes have uPVC guttering as it’s a hardwearing plastic that should last a long time. But you’ll also see gutters made from aluminium, cast iron and copper, especially on period homes or those in a conservation area.

Every home needs a guttering system to ensure that rainwater doesn’t affect the foundations of the property. It’s also important to keep the gutters clear of debris like fallen leaves, as this will cause them to overflow, potentially causing water to soak into the walls and causing damp.

Clean of your conservatory gutter is probably not one of the most enjoyable chores you’d like to take on around the house. Not only is it messy and tedious, but it’s also time consuming and smelly. It’s a job every home and property owner would rather avoid, but unfortunately everyone has to do it. It’s a necessity due to the fact that neglect gutters holds and harbours mould, moss as well as plant debris. It would have been better if this is only disgusting, but the actual truth is that should be the least of your worries as this gradual build up of organic material in your conservatory gutters can minimize their drainage abilities, leading to leakages and spills that can damage your conservatory.

Cleaning of your conservatory gutter is a task that can be done regardless of your level of experience. However, it’s advisable to call in a professional for help especially if you lack the confidence required to pull it off.

• Use a ladder for a closer look. Cleaning your gutters from the ground by poking it with a hooked tool might seem the best way out, but in truth you risk damaging the gutters or brackets and marking the conservatory panes when you don’t see what you’re doing.
• Invest in specialist tools. For expert DIYers, taking off your downpipes from the wall to clean might be a pretty easy task. However, for most people it can be extremely frustrating. As a result, there’s the need to get hold of some flexible gutter brushes. With a bendable stem and stiff bristles, these are able to hook and dislodge dirt and leaves inside your downpipes with relative ease.

Soffit is a word gotten from two languages - French and Latin, whereby the root word implies to “form as a ceiling in French, while it means to “to fix underneath in Latin. Basically, soffit is a portion of the ceiling that has been constructed lower than the area that surrounds it. And even though they aren’t that much popular in recent times, they happen to be a common feature in kitchens of older homes in the UK. At times, a soffit can occupy the whole room or area in a home.

Homeowners across the globe make use of this feature mostly as a decorative element in the room , however, there are also times in which they may be required for various purposes. These purposes include using soffits to conceal plumbing pipes or, heating or cooling ducts, which is often the case when sofits are constructed at the lower levels of homes. They’re also often incorporated in bathrooms or kitchens as soffits house light fixtures. For instance, recessed light fixtures fitted over kitchen or bathroom sinks are mostly fitted into a soffit. What’s more? Soffit can also be required in a room because of the home’s structure as the feature can be used to hide a structural beam.

If you happen to own an older home and you’d like to remove an existing soffit, the first step is to ensure that its safe to carry out such plan. You should firstly check for any electrical lines, ductwork, lighting or structural problems that may exist prior to the commencement of the project. If you’re not sure or confident enough to pull this off, then it’s advisable to consult a professional contractor before you proceed.

Soffits are constructed by homeowners on their properties for several purposes. Not only are they incorporated to hide away the unsightly features of a home, but they can also be used to add decorative architectural detail. Soffits construction, on the other hand, is a project that can be done by any DIY person with the knowledge and experience. However, if you lack the confidence to pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the best results, the first time. In this guide, we’re are going to take you through the soffit construction process.

✓ Measure and mark. The first step is to take an accurate measurement of the size of your propose soffit and use a pencil to mark it out on both the wall and ceiling. The size of your soffits is mainly determined by your needs or preferences.

✓ Cut and Install Wall & Ceiling Plates. Proceed to cut the wall as well as ceiling plates once the dimensions have been marked. Make use of 2x4 lumber, you can cut to size with the help of a table saw or mitre. Once done, you can then attach it to the wall as well as ceiling studs with a framing nail gun.

✓ Build the box frame. Develop a box-frame from 2x4 lumber, using your measurements as guide.

✓ Fit the box frame. Hold the box frame in place with some slide clamps and then attach it to the ceiling and wall plates with drywall screws.

✓ Mark the studs. Make use of a pencil to mark out the studs location on your soffit box frame.

✓ Cut and hang the drywall. Cut the drywall with a utility knife uing your measurement as a guide. Once done, attach the drywall to the framework with the help of drywall screws.

✓ Add finishing touches. This includes installing the corner beads, finishing off with the common drywall work of taping, spackling and sanding. Once the spackle is dry, you can the complete it by painting the soffit.

Leaves, twigs and moss all have one thing in common which often annoys home and property owners - they are the three main materials that negatively impacts the proper functioning of a roof guttering system. The major cause of water drainage problems for most homes and buildings are these organic materials. Wondering how some leaves and few twigs can cause such a big problem? Over time there’ll be a gradual build up of the natural debris in your gutter system which starts to rot and turn  to a thick and muddy goo which obstructs the flow of water in your drainage. As a result, there’s the need to make sure that your gutters are thoroughly cleaned at least twice annually in order to prevent bigger issues that can be caused by the blockage of a drainage system.

So if you’re considering getting your gutters cleaned by a professional, you’d probably be interested in know just how it’s going to cost. Well, there’s not straightforward and simple answer to this question as there are a number of factors that contributes to the final cleaning cost of your gutters.

In general, in the UK, the average cost for cleaning of gutter is usually around £18 to about £25 per hour. However, you can also be quoted a day rate which is usually ranging between £150 to £200 per day.

The factors that can affect gutter cleaning price includes the type of your property (such as a terraced, end of terraced, detached and semi detached homes) which possesses a varying gutter cleaning price largely due to their size differences, the height of the building ( if you require the service for a property located on the second floor of a building, this would be a bit higher than if it were to be on the ground floor) as well as additional requests.

To keep water away from your house, the importance of gutters cannot be overemphasized. However, in order to enable them do their job the proper way, the clogging dirt and debris must be thoroughly wiped out and fortunately there are a number of ways to get the job done by yourself. However, it must be stated that cleaning of gutters can be a very dangerous task as it deals with working at heights. As a result, if you are not confident enough to this pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the job effectively and also in a safe manner. In this guide, we’re going to look at some of the ways in which you get rid of dirt and debris on your gutter by yourself.

• Clean the gutter with a leaf blower. Several leaf blowers feature a nozzle attachment which is made to release a narrow stream of air which is suitable for cleaning of gutters. All you have to do is simply to position your ladder to enable you work slowly towards the downspout and getting rid of all dirt and obstructions on the gutter as you go. The final step would be to remove any lingering leaves or twigs using a hose. If don’t want to stand on a ladder to do all these, a specialized attachment is available to add to the blower’s reach.
• Clean the gutter with a wet or dry vacuum. For heavier debris, you can try out a wet or dry vacuum. To reach the obstructed gutters while standing on the ground, simply get curved attachments and hoses at a local home improvement store. You may, however, need to moisten some stubborn dirt before it can be properly vacuumed or removed.after completing the vacuuming process, simply flush the gutters with garden hose waters.

Soffits and fascias sit along the sides of your property, over the join between your walls and your roof. The fascia attaches to the end of your roof rafters, hiding and protecting them. The soffit fixes on the bottom of the fascia, bridging the gap between your fascia and wall. Your guttering attaches to the fascia, which also joins to the bargeboard on your gable end, if you have one.