Find a Gutter Installer you can trust in Inveraray.

Yes, it’s a dirty job, but every homeowner out there has got to do it! Your gutter needs to be free of dead leaves, birds’ nest and other debris as well as being through clean in order to perform its functions effectively. It’s just a part of the responsibilities that comes with owning a home. Dry leaves, tree branches and other materials build up in your gutters overtime especially during the dry summer and you won’t notice until the point where your gutters start overflowing during the first main rain of the season.

In the event whereby your dirty and clogged gutter is left unattended to, this can lead to several issues like a leaky gutter and mold, leaky roof and basements,cracked foundation, driveway and yard damage and several more which will definitely make you incur more unnecessary expenses. So the question is, how often should the gutters be cleaned? The answer is, it depends. According to several experts, gutters should be cleaned at least twice a year - which is once in the late spring and once in the late summer or early fall. However, there are a couple of factors that may make you have a rethink.

If you happen to have a pine tree growing above your house, it’ll be wise to consider inspecting your gutters every 3 months. This is because pine trees shed needles year-round and they usually have a lot of these needles to shed. In the situation whereby you’re located at a higher elevation, ice is will most likely be your greatest source of concern. Making sure that your gutters remain clean throughout the winter can be quite a headache, but damage to your roof cause by ice can be an even greater pain. Prevention is always better than cure.

Soffits are constructed by homeowners on their properties for several purposes. Not only are they incorporated to hide away the unsightly features of a home, but they can also be used to add decorative architectural detail. Soffits construction, on the other hand, is a project that can be done by any DIY person with the knowledge and experience. However, if you lack the confidence to pull this off, then we’d strongly recommend you get in touch with a reliable professional who can guarantee the best results, the first time. In this guide, we’re are going to take you through the soffit construction process.

✓ Measure and mark. The first step is to take an accurate measurement of the size of your propose soffit and use a pencil to mark it out on both the wall and ceiling. The size of your soffits is mainly determined by your needs or preferences.

✓ Cut and Install Wall & Ceiling Plates. Proceed to cut the wall as well as ceiling plates once the dimensions have been marked. Make use of 2x4 lumber, you can cut to size with the help of a table saw or mitre. Once done, you can then attach it to the wall as well as ceiling studs with a framing nail gun.

✓ Build the box frame. Develop a box-frame from 2x4 lumber, using your measurements as guide.

✓ Fit the box frame. Hold the box frame in place with some slide clamps and then attach it to the ceiling and wall plates with drywall screws.

✓ Mark the studs. Make use of a pencil to mark out the studs location on your soffit box frame.

✓ Cut and hang the drywall. Cut the drywall with a utility knife uing your measurement as a guide. Once done, attach the drywall to the framework with the help of drywall screws.

✓ Add finishing touches. This includes installing the corner beads, finishing off with the common drywall work of taping, spackling and sanding. Once the spackle is dry, you can the complete it by painting the soffit.

• A sturdy ladder
• Gloves and safety goggles
• A hammer and nails to secure your fascia so it doesn’t fall down mid-replacement
• A hacksaw – this will cut through uPVC guttering – just make sure you leave a margin of error with every cut you make
• Cable ties or rope to secure the existing gutters while you dismantle them, so they don’t fall off
• All the right fixings and brackets to secure the guttering
• An electric drill and/or screwdrivers

1. Add a gutter bracket to the top of the fascia board at the opposite end to the stop-end outlet, if you have one. Then tie a piece of string around the base of the bracket.
2. You’ll need to place the gutter outlet accurately over the drain. Hold a plumb line against the fascia directly over the drain, and mark that position with a pencil. Following the manufacturer’s advice on the number of screws to use, fit the gutter outlet no more than 50mm below the level of the roof tiles.
3. Stretch the piece of string you tied on the bracket along the fascia board, and tie it to the outlet. Make sure you check with a spirit level that the string slopes towards the outlet.
4. Mark the positions of the other brackets. They should be no more than 800mm apart, or 600mm if your roof is very steep. They also shouldn’t be any more than 150mm from a joint or fitting. Then fit the rest of the brackets.
5. Fit a stop-end to the first length of gutter and clip it into position on the brackets. At the other end, fit a union piece and screw it into the fascia.
6. Then fit the next length of gutter into it, and the next until you’re finished. Cut the last one to fit using your hacksaw before attaching a stop-end. Then make sure all the joints line up with the insertion depth marks on the fittings. Then you’re done!

It may be shocking a whole lot of people would not be able to point out fascias and soffits on a building despite the fact that they’re an essential part of the roof. To give you an idea, they’re simply used to cover the roof beams’ ends that comes out of the wall from underneath of the roof. The board that runs vertically just below the roofline is the fascia board, which is also the long length of UPVC. Therefore if you look at the gutters located in the front of house, the board behind is called the fascia board. However, soffits runs horizontally from behind the gutters to the wall of a building, so if you walk close to a house and look up, you’ll identify the soffits. They’re done to cover the gaps between the wall house and the gutters. The main function of both soffit and fascia is to divert water away from your roof as well as walls.

Fascias and soffits were usually made of wood before UPVC came along. And as a result, they only require little maintenance, no more warping, painting or cracks unlike the wooden ones. However they also can’t last an eternity, so when the time comes and you need to replace your soffit and fascia, you’ll probably want to know just how much it’s going to cost.

Unfortunately, there’s no way to calculate an accurate cost for fascias and soffits as there are too many variables to put into consideration. These includes the type of fascia and soffit you choose as well as the size of your property. However the average cost to replace a three bed semi-detached house’s fascias and soffits is within the range of £1200 to £1500 or even more if you’re staying in London or in a larger detached building.

Having ventilation in the roof void is a requirement for building regulations approval. Fitting ventilated soffits is the typical way that this roof ventilation is achieved. If you do not have roof ventilation, you may find that your roof void has problems with condensation or overheating.

In general uPVC is used for soffits and fascias as it is very strong and durable. It also requires very little maintenance. However, wood can be used and is still popular on listed properties as it retains the original material. Older and listed buildings may require more traditional materials to be used.

1. Hang a plumb bob from the outlet to the drain to use as a guide while you draw several marks on the wall with a pencil to show you where the downpipe will run.
2. Join the marks up with a straight edge, creating a line to show where the centre of the downpipe will be.
3. Position a downpipe clip at the top of wall, in the centre of the pencil line. Mark the position of its fixing holes on the wall. If you need an offset bend, put a downpipe clip directly below the bend.
4. Repeat the process down the wall. Make sure there is no more than 1.8 metres between pipe clips.
5. Refer to the guttering manufacturer’s instructions to see which drill bit is required. Use a drill to drill the fixing holes and insert wall plugs.
6. Fit the first piece of downpipe starting from the outlet and moving towards the drain.
7. If you need to add more downpipe, join the two pieces with a pipe socket and clip. Leave a 10mm gap between the end of the pipe and the bottom of the pipe socket, because it will probably expand. Then attach a pipe clip over the joint.
8. Continue attaching pipe clips down the length of the downpipe.
9. If you need to, fit a downpipe show to direct the water into the drain. Attach a downpipe clip directly below the socket of the shoe.