Find a Flooring Fittter you can trust in Swindon.

The cost of wood flooring varies by the type of wood and by the finish required. As a guide though oak solid wood flooring cost about £35 - £45 per m2. The average wooden cost by material are approximately £40 per m2 for pine, £45 per m2 for cherry, £60 per m2 for maple and £75 per m2 for walnut. This price does exclude the laying of the flooring and the underlay required.

How To Lay Wood Flooring

Laying of wood flooring is actually a very simple task contrary to many beliefs. First and foremost, before commencement of the fitting process, you must determine the direction you would like the engineered wood flooring to lie in. To do this the right way, they should lie in the direction of the the longest wall. However, if your subfloor is wooden, then having the boards positioned across the joists underneath would be your best bet to get started.

Here are some simple steps to follow to properly lay your wood flooring:

• Start from a corner, working from left to right and place the initial rows of the boards with the groove’s end directly opposite the closest wall.

• Make use of expansion spacers. Place them in between the wall and the board alongside an expansion gap of about 8 to 10mm.

• Place the board’s final rows at about 100mm wide. To achieve this, it is crucial to be pro-active with the measurement and cut the boards (if you deem fit) to adjust the first row.

• With the help of the click system, the boards will click together.

• Fit in the next board. Ensure to attach the tongues together (30 degrees from the floor) and once done, you can proceed to lower and lock it in place. Do this till you get to the end of the row.

• Cut the last board of the row to size if its too long.

• If the part cut off is up to 300mm, simply use it to start the next row. If not, cut a new board in half to use.

• Put the rows side by side in such a way to ensure the joints are staggered at each and every row. Keep a consistent gap between the wall and the planks via the continuous use of the spacers.

• Lay a plank over the last row to determine the width of the previous board. Position a new plank in a way that its tongue is directly against the wall. Once done, proceed to mark a line of plank underneath to get the required width. Then, fit the plank into the space with the help of a pull bar and hammer.

Click here to learn more about wood flooring.

In order to get a good idea for how much is needed, there’s a need to measure a room for carpet. This is an essential step that should be completed before you shop for brand new carpets to install. Taking the measurement for a basic square or an oblong area is actually relatively easy as long as you put the doorways and entry stairs into consideration. If you’re looking for the best way to measure for carpet, then you’ve come to the right place. In this post, we’re going to take you through room measurement for carpet procedures.

To get started, you’re going to need a measuring tape or a laser distance measurer, a paper and writing instrument or note taking app, a calculator or calculator app as well as a graph paper and a pencil if you wish to draw your layout.

1. Draw a simple diagram of your home. This doesn’t have to be perfect, but you’d have to ensure the measurements taken are accurate. All that’s needed is a basic drawing featuring all the rooms shown. What’s more? If the room happens to be square or rectangular, you can calculate the area simply by multiplying the width by the length.
2. Chimneys and recesses. If the room in question features chimneys breasts and recesses, take a measurement of the entire space and ignore them, the flooring or carpet will simply be cut around them.
3. Calculating the final figure. Take a measurement of each area and put it down in the relevant space on the diagram. Then, simply break the room down to smaller rectangular shapes, determine their area and add them together to obtain the total area of your room. You can make an allowance of up to 5 percent of the total for possible waste.

Wooden flooring is very popular flooring option amongst home and property owners in the UK and understandably so. It adds to your space’s curb appeal, it’s quite easy to maintain, it adds to the value resale value of your property if you later wish to sell and lots more. If you’re looking to have wooden flooring installed in your home, you have two options which includes doing it yourself or calling in a professional – the latter being more advisable. However, by following some simple but essential steps, you can also install your wooden flooring successfully by yourself. These includes determining the site is in the best condition before installation, removal of all floor coverings and underlay for a more stable and durable installation and incorporation of the right expansion gap of about 10mm to 12mm which would be maintained around the floor’s perimeter.

Wooden floor fitting can be done on two types of sub-floor - Concrete and Plywood. To install onto concrete, you can follow the guide below:

• Incorporate flexible wood on concrete adhesives.
• With the help of a 3mm toothed trowel, spread above 2 board widths of adhesive along the starting wall sub-floor, beginning at a corner of your room.
• Position the first row of flooring into the area that is glued using the tongue facing opposite the wall.
• Put 10mm spacers against the wall to see to the consistency in expansion gaps.
• Make sure the joints are at a minimum of 150mm apart from the first row when fitting the second row.
• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.
• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

To install onto plywood, you can follow this guide:

• Make use of a porta-nailer.
• Position 10mm spacers against the wall - parallel with the installation direction.
• Fit the first row using the tongue facing opposite the wall and with the help of the porta-nailer or flooring nailer.
• Lay the second row and make sure the short end joints are at a minimum of 150mm apart from that of the first row.
• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.
• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

If you’re thinking about making improvements to your home, it’s only reasonable to become familiar with the ins and outs of the requirements to make the project a success. Not just the cost involved to complete the project, but also the duration it’ll take to complete the job and lots more. When it comes to the installation of wooden flooring, there’s a need to find out whether or not an underlay is required for the task. In this article, we’re going to consider this in order to ensure that you’re on the right track. Let’s take a look!

First and foremost, underlays are common with carpets as they allow for an even surface with no lumps and bumps. It also provides a deeper barrier between the carpet and the floor as carpets, themselves, aren’t particularly thick enough to provide adequate comfort when walking on them. Underlay also helps improve insulation which in turn, helps cut down your energy bill. So, are underlays also needed with wooden flooring?

In general, wooden flooring does not really need an underlay. This is due to the fact that they’re perfectly comfortable to walk on without the need to add an extra padding underneath. However, the subfloor will have to be made prior to the installation, as a result, an underlay is needed at all there. With that in mind, it’s highly recommended to make use of an underlay when installing a boarded floor to a wooden subfloor mainly due to the fact that it’s able to provide a much-improved insulation. When it comes to wooden flooring, it’s always best to go for quality rather than looking for ways to cut corners. If you’re able to go for the best project with professional installation and little extras like undelay, you’d notice and enjoy the long lasting nature of your wooden flooring immediately after installation.

Are you a new homeowner? Or perhaps you’re simply looking to revitalize your home by adding some new flooring options. Wooden flooring is one of the most popular flooring options amongst home and property owners in the UK due to the multiple benefits it offers. It adds your home’s curb appeal making it stand out while also adding to resale value of your home - should you decide to sell in the near future. When it comes to the installation of wooden flooring, you have two options which includes carrying out the installation yourself or calling in a professional for help. While some homeowners would prefer to tackle this themselves, it’s highly advisable to get professional support for the project. In this article, we’re going to consider some of the benefits you stand to derive from getting your wooden flooring installed by a professional. Let’s take a look!  Efficient installation. Since professionals do this type of work almost on a daily basis, they’re generally able to complete a basic job within a day or two. With them, you’d be certain that you job would be completed to perfection within a certain timeframe.  Access to a range of wooden flooring options. Professionals are usually familiar with top notch wooden flooring options so they’re able to make recommendations on the most suitable wooden flooring type for your home and needs.  Flooring removal. Professionals typically remove old or existing flooring and clean up the area prior to the installation of the new wooden flooring. This way, you wouldn’t have to bother about hiring someone else to remove the existing flooring or to clean up the entire area before you can be able to install the new wooden flooring yourself.

If you’re thinking of getting a new carpet, one of the most likely issues you’re going to face is how to identify the types of carpet as there are a plethora of options in the market today. Being able to identify types of carpet can go a long way to make sure you get the most suitable type for your home without having to pay a professional. In this post, we’re going to consider the types of carpets and how you can identify them with ease. Let’s take a look!

When it comes of carpet construction, there are two main types which are defined by how their fibres are attached to their backings. These includes:

1. Loop pile. These are carpets which the fibres are bent into the small loops. They’re known to be very durable and stain resistant, however they also have a low profile as well as a limited cushioning. The loop pile style encapsulates the following:
2. Level loop ( also referred to as Berber). This carpet type features short loops which stand up well in traffic areas.
3. Multi level loop. This implies that the tops of the loops are different in height so as to give the carpet a patterned texture.
4. Cut pile. These are carpet types that cut the yarn tips to ensure there isn’t any loops. They tend to be denser and softer when compared to loop pile. The types of cut pile includes plush, saxony, textured cut pile, frieze carpet and cable.

On the other hand, carpets are made from different synthetic and natural fibres with varying characteristics. These includes nylon (the most popular as its durable and, wear and stain resistant), olefin ( resistant to moisture, mildew and mold), acrylic (a cheaper alternative to wool) and wool (the premier carpeting option and the only natural fibre used in manufacturing carpets).

Adding brand new carpets is one of the quickest ways you can employ to revamp your room and update your home design. Whether you’re looking to inject a new lease of life through a splash of colour or perhaps you simply wish to replace the current worn out or tired looking thread-bare floor, a new carpet can go a long way to have a major impact on how your home feels and looks. At the same time, it can also be a relatively inexpensive way to make a significant change. However, it’s always essential to know the cost before carrying out such a project. In this post, we’re going to consider room recarpeting costs in order to help you make the best informed decision possible moving forward. Let’s take a look!

Generally, carpet are priced per square metre and the cost depends on a number of factors which includes the material as well as the manufacture of the carpet you opt for. On the lower side of the spectrum, you can expect to incur as little as £5 per square metre for a simple and synthetic carpet, while at the other end, a luxurious woolen carpet can cost in excess of £30 per square metre.

While the major and most significant part of the cost would be the price of the material itself, there are however other costs you’ll need to take into account. These costs includes the cost of the underlay which is usually within the range of £5 per square metre to about £15 per square metre, the carpet grippers as well as the cost of labour. Overall, the total cost for a carpet fitting job is normally within the range of £13 per square metre for a simple carpet and installation, and £50 per square metre for a luxurious carpet.