Find a Flooring Fittter you can trust in Highbridge.

The cost of wood flooring varies by the type of wood and by the finish required. As a guide though oak solid wood flooring cost about £35 - £45 per m2. The average wooden cost by material are approximately £40 per m2 for pine, £45 per m2 for cherry, £60 per m2 for maple and £75 per m2 for walnut. This price does exclude the laying of the flooring and the underlay required.

Adding brand new carpets is one of the quickest ways you can employ to revamp your room and update your home design. Whether you’re looking to inject a new lease of life through a splash of colour or perhaps you simply wish to replace the current worn out or tired looking thread-bare floor, a new carpet can go a long way to have a major impact on how your home feels and looks. At the same time, it can also be a relatively inexpensive way to make a significant change. However, it’s always essential to know the cost before carrying out such a project. In this post, we’re going to consider room recarpeting costs in order to help you make the best informed decision possible moving forward. Let’s take a look!

Generally, carpet are priced per square metre and the cost depends on a number of factors which includes the material as well as the manufacture of the carpet you opt for. On the lower side of the spectrum, you can expect to incur as little as £5 per square metre for a simple and synthetic carpet, while at the other end, a luxurious woolen carpet can cost in excess of £30 per square metre.

While the major and most significant part of the cost would be the price of the material itself, there are however other costs you’ll need to take into account. These costs includes the cost of the underlay which is usually within the range of £5 per square metre to about £15 per square metre, the carpet grippers as well as the cost of labour. Overall, the total cost for a carpet fitting job is normally within the range of £13 per square metre for a simple carpet and installation, and £50 per square metre for a luxurious carpet.

Whether you’re looking to add a bit of colour to your stairs or perhaps you just want to replace the current tired and lacklustre carpets, adding a brand new carpet to your stairs can be all that’s needed to glow up your home. However, before you get started there’s always a need to consider the cost of undertaking such a project to prevent any unpleasant surprises. In this article, we’re going to consider the cost to carpet stairs in order to help you make the best decisions as you proceed. Let’s take a look!

Generally, it’s important to note that the type of stair you have can play a key role in the carpet fitting cost. However, you can expect to incur a minimum of £30 to have you carpet professionally fitted. This applies only to the fitting costs, other costs such as delivery, removal of old carpets as well as the cost of any other item that needs to be installed to keep your new carpet in the right place.

When it comes to delivery costs, it very unlikely you’re going to get a free delivery of your carpet unless you pick it up yourself. Depending on the company you select, this could cost about £30 or more. What’s more? The removal of the old carpet will also be included in the overall carpet fitting cost, if you decide to have it removed by a professional. Once removed, the next cost that arises is disposal costs. If you request your old carpet is properly disposed by your carpet fitting company, this could generate up to £50 additional cost. Alternatively, you can take the old carpet to your local council waste site or tip and dispose it for free.

If you’re replacing your carpet with new carpet, you might be able to use your old underlay. This is dependant on how long the existing carpet has been down for and also the condition of the underlay. But if you’re getting wood, laminate or vinyl flooring it’s not suitable. It will put stress on the joints if you use underlay.

With a large variety of carpet types in the market today, it can be incredibly difficult to separate the “the boys from the men. To a great number of home and property owners, what matters is the visual appeal as well as the affordability of the carpet. Once they find one that fits the bill, they simply purchase ignoring the suitability of the carpet for their homes. In several cases, this will often turn out to be disastrous especially when it happens to be a total mismatch. For instance, when you install a carpet that’s not designed to withstand a heavy footfall in a highly busy household or booming business. If you’re looking to get the best possible carpet, then you’ve found the perfect company. In this post, we’re going to consider the best carpet type to help you make informed purchase decisions going forward. Let’s take a look!

Primarily, loop pile and cut pile are the two types that are available in the market today.

• The loop style pile. Here, the individual ends are linked into the backing to ensure a continuous loop.
• The cut style pile. For this carpet style, the loops are cut to ensure that each ends are sticking up through the backing - similar to a sheer cut pile.

There are three main types of fibres used today in carpet construction that you should consider. These includes polypropylene, polyester as well as nylon. Furthermore, the most popular choice today when it comes to natural fibre is wool. However, wool’s high price makes it less common and often considered as a luxurious option. For heavy traffic areas, the best carpets are usually loop pile styles to ensure maximum value is derived from your asset. On the other hand, if you want an easy-to-clean carpet, then olefin and polyester should be on the top of your list.

Though both solid wood and engineered wood can be installed on a concrete sub-floor, the processes are quite different from each other. Solid wood is produced from a single plank of wood which can be reactive to both temperature and humidity changes which is capable of making the wood expand or contract. Hence, the different approach to solid wood and engineered wood flooring installation on concrete. Here, we’ll discuss how you can lay solid wood on your concrete.

First and foremost, you’d have to determine the method you’ll use to attach the planks to the floor. Is it floating whereby you only have to lay the wood flooring on the concrete after fitting the right underlay? You can also go for the most popular installation method which is gluing your floor with a flexible wood adhesive (to be applied to both the boards and the sub-floor). Or perhaps you’d prefer to use the traditional method of nailing the boards to the concrete (the nails will be covered as you lay the subsequent planks and the groove locks with the tongue).

After making this decision, you’d have to ensure that the sub-floor is well prepared for the installation. This implies checking the wood’s moisture content (mustn’t exceed 7 to 8 percent). Also inspect the floor to ensure its neat, if not, clear out the dirt or debris and make sure the surface is flat to avoid post-installation problems.

In the event whereby you discover a high moisture content, you’d want to acquire a damp proof membrane. This will not only enhance the floor’s stability, but also prevent shrinking or warping of the wood due to changes in humidity or temperature.

It is crucial to note that the preparation of the sub-floor is equally as important as the laying of the planks as this can go a long way to improve the durability and strength of your floor. Click here to learn more about wood flooring.

How To Lay Wood Flooring

Laying of wood flooring is actually a very simple task contrary to many beliefs. First and foremost, before commencement of the fitting process, you must determine the direction you would like the engineered wood flooring to lie in. To do this the right way, they should lie in the direction of the the longest wall. However, if your subfloor is wooden, then having the boards positioned across the joists underneath would be your best bet to get started.

Here are some simple steps to follow to properly lay your wood flooring:

• Start from a corner, working from left to right and place the initial rows of the boards with the groove’s end directly opposite the closest wall.

• Make use of expansion spacers. Place them in between the wall and the board alongside an expansion gap of about 8 to 10mm.

• Place the board’s final rows at about 100mm wide. To achieve this, it is crucial to be pro-active with the measurement and cut the boards (if you deem fit) to adjust the first row.

• With the help of the click system, the boards will click together.

• Fit in the next board. Ensure to attach the tongues together (30 degrees from the floor) and once done, you can proceed to lower and lock it in place. Do this till you get to the end of the row.

• Cut the last board of the row to size if its too long.

• If the part cut off is up to 300mm, simply use it to start the next row. If not, cut a new board in half to use.

• Put the rows side by side in such a way to ensure the joints are staggered at each and every row. Keep a consistent gap between the wall and the planks via the continuous use of the spacers.

• Lay a plank over the last row to determine the width of the previous board. Position a new plank in a way that its tongue is directly against the wall. Once done, proceed to mark a line of plank underneath to get the required width. Then, fit the plank into the space with the help of a pull bar and hammer.

Click here to learn more about wood flooring.

Installing wooden flooring is a quite simple process, however to get it right the first time, there are very essential preparations that must be made. These includes determining the site is in the best condition before installation, removal of all floor coverings and underlay for a more stable and durable installation and incorporation of the right expansion gap of about 10mm to 12mm which would be maintained around the floor’s perimeter.

Wooden floor fitting can be done on two types of sub-floor - Concrete and Plywood. To install onto concrete, you can follow the guide below:

• Incorporate flexible wood on concrete adhesives.

• With the help of a 3mm toothed trowel, spread above 2 board widths of adhesive along the starting wall sub-floor, beginning at a corner of your room.

• Position the first row of flooring into the area that is glued using the tongue facing opposite the wall.

• Put 10mm spacers against the wall to see to the consistency in expansion gaps.

• Make sure the joints are at a minimum of 150mm apart from the first row when fitting the second row.

• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.

• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

To install onto plywood, you can follow this guide:

• Make use of a porta-nailer.

• Position 10mm spacers against the wall - parallel with the installation direction.

• Fit the first row using the tongue facing opposite the wall and with the help of the porta-nailer or flooring nailer.

• Lay the second row and make sure the short end joints are at a minimum of 150mm apart from that of the first row.

• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.

• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

Click here to learn more about wood flooring.