Find a Flooring Fittter you can trust in Golspie.

Though both solid wood and engineered wood can be installed on a concrete sub-floor, the processes are quite different from each other. Solid wood is produced from a single plank of wood which can be reactive to both temperature and humidity changes which is capable of making the wood expand or contract. Hence, the different approach to solid wood and engineered wood flooring installation on concrete. Here, we’ll discuss how you can lay solid wood on your concrete.

First and foremost, you’d have to determine the method you’ll use to attach the planks to the floor. Is it floating whereby you only have to lay the wood flooring on the concrete after fitting the right underlay? You can also go for the most popular installation method which is gluing your floor with a flexible wood adhesive (to be applied to both the boards and the sub-floor). Or perhaps you’d prefer to use the traditional method of nailing the boards to the concrete (the nails will be covered as you lay the subsequent planks and the groove locks with the tongue).

After making this decision, you’d have to ensure that the sub-floor is well prepared for the installation. This implies checking the wood’s moisture content (mustn’t exceed 7 to 8 percent). Also inspect the floor to ensure its neat, if not, clear out the dirt or debris and make sure the surface is flat to avoid post-installation problems.

In the event whereby you discover a high moisture content, you’d want to acquire a damp proof membrane. This will not only enhance the floor’s stability, but also prevent shrinking or warping of the wood due to changes in humidity or temperature.

It is crucial to note that the preparation of the sub-floor is equally as important as the laying of the planks as this can go a long way to improve the durability and strength of your floor. Click here to learn more about wood flooring.

If you’re thinking about installing a carpet on your floor, one of the most important things you’d have to put into consideration before you proceed is the most suitable type of underlay to ensure your carpet is placed appropriately and maximum value is derived. This is a common issue for several homeowners and we aim to help you clear the worries once and for all. In this post, we’re going to consider the best underlay for your carpet to help you make the best informed decision moving forward. Let’s take a look!

In all honesty, there’s no straightforward answer to this question as the best carpet underlay depends on a number of factors. These factors include the type of carpet you wish to install, the type of flooring it will sit on ( e.g, concrete or underfloor heating), your budget, the room you’re laying the underlay in as well as your personal preferences in terms of durability, comfort, noise reduction and more.

When a carpet underlay is carefully selected, it’ll act as a shock absorber - perfect for protecting your floors against high traffic and impact, making sure that your carpeted floor looks good and healthy for a long period of time.

Generally, the best carpet underlay for bedrooms will be a thick, sponge rubber underlay or a wool combination felt variation which guarantees your comfort. For living rooms and lounges, the best carpet underlay would be one that is sumptuous and velvety soft to provide a comfortable floor. For dining rooms, you’d be smart to get a good quality hard-wearing carpet underlay as this area is one of the most frequently occupied areas in the home.

Are you looking to renovate your home or property by laying a brand new carpet? Or perhaps your current carpet has started giving indications that it’s well past its glorious days and needs to be replaced. Regardless of the reason why you wish to recarpet your home, you’d probably find yourself asking the same question almost every home and property owner in a similar situation asks - how much does it cost to recarpet a house? Well, you’ve come to the right place! In this post, we’re going to take a good look at house recarpeting costs.

Generally, carpet fitting costs can be within the range of £5 per square meter to about £30 per square meter. However, when it comes carpet costs itself, a short and accurate answer can’t be provided. This is due to the fact that carpet costs can vary largely based on a number of factors which includes the weaves, the texture, the material incorporated ( such as wool, cotton, polyester, polypropylene and more), the pile depth, the colour as well as the brand. What’s more? You’re probably going to want varying carpet types for different areas of your home. For instance, you should use a more robust material for your stairs than what you’d probably get for your living area.

Overall, if you want a low budget carpet, you should be able to get one anywhere within the range of £5 per square meter to £10 per square meter.  On the other hand, if you have a mid range budget, you can expect to find carpets anywhere within the range of £15 per square meter to £20 per square meter. And finally, if you’re looking for luxurious carpets, the price starts at £30 per square meter.

Adding brand new carpets is one of the quickest ways you can employ to revamp your room and update your home design. Whether you’re looking to inject a new lease of life through a splash of colour or perhaps you simply wish to replace the current worn out or tired looking thread-bare floor, a new carpet can go a long way to have a major impact on how your home feels and looks. At the same time, it can also be a relatively inexpensive way to make a significant change. However, it’s always essential to know the cost before carrying out such a project. In this post, we’re going to consider room recarpeting costs in order to help you make the best informed decision possible moving forward. Let’s take a look!

Generally, carpet are priced per square metre and the cost depends on a number of factors which includes the material as well as the manufacture of the carpet you opt for. On the lower side of the spectrum, you can expect to incur as little as £5 per square metre for a simple and synthetic carpet, while at the other end, a luxurious woolen carpet can cost in excess of £30 per square metre.

While the major and most significant part of the cost would be the price of the material itself, there are however other costs you’ll need to take into account. These costs includes the cost of the underlay which is usually within the range of £5 per square metre to about £15 per square metre, the carpet grippers as well as the cost of labour. Overall, the total cost for a carpet fitting job is normally within the range of £13 per square metre for a simple carpet and installation, and £50 per square metre for a luxurious carpet.

Installing wooden flooring is a quite simple process, however to get it right the first time, there are very essential preparations that must be made. These includes determining the site is in the best condition before installation, removal of all floor coverings and underlay for a more stable and durable installation and incorporation of the right expansion gap of about 10mm to 12mm which would be maintained around the floor’s perimeter.

Wooden floor fitting can be done on two types of sub-floor - Concrete and Plywood. To install onto concrete, you can follow the guide below:

• Incorporate flexible wood on concrete adhesives.

• With the help of a 3mm toothed trowel, spread above 2 board widths of adhesive along the starting wall sub-floor, beginning at a corner of your room.

• Position the first row of flooring into the area that is glued using the tongue facing opposite the wall.

• Put 10mm spacers against the wall to see to the consistency in expansion gaps.

• Make sure the joints are at a minimum of 150mm apart from the first row when fitting the second row.

• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.

• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

To install onto plywood, you can follow this guide:

• Make use of a porta-nailer.

• Position 10mm spacers against the wall - parallel with the installation direction.

• Fit the first row using the tongue facing opposite the wall and with the help of the porta-nailer or flooring nailer.

• Lay the second row and make sure the short end joints are at a minimum of 150mm apart from that of the first row.

• Utilize pre-cut smaller boards if you’re to start a new row with staggered joints.

• Continue with this nailing method and make sure the 10mm expansion gaps are consistent around the floor’s perimeter.

Click here to learn more about wood flooring.

If you’re thinking of getting a new carpet, one of the most likely issues you’re going to face is how to identify the types of carpet as there are a plethora of options in the market today. Being able to identify types of carpet can go a long way to make sure you get the most suitable type for your home without having to pay a professional. In this post, we’re going to consider the types of carpets and how you can identify them with ease. Let’s take a look!

When it comes of carpet construction, there are two main types which are defined by how their fibres are attached to their backings. These includes:

1. Loop pile. These are carpets which the fibres are bent into the small loops. They’re known to be very durable and stain resistant, however they also have a low profile as well as a limited cushioning. The loop pile style encapsulates the following:
2. Level loop ( also referred to as Berber). This carpet type features short loops which stand up well in traffic areas.
3. Multi level loop. This implies that the tops of the loops are different in height so as to give the carpet a patterned texture.
4. Cut pile. These are carpet types that cut the yarn tips to ensure there isn’t any loops. They tend to be denser and softer when compared to loop pile. The types of cut pile includes plush, saxony, textured cut pile, frieze carpet and cable.

On the other hand, carpets are made from different synthetic and natural fibres with varying characteristics. These includes nylon (the most popular as its durable and, wear and stain resistant), olefin ( resistant to moisture, mildew and mold), acrylic (a cheaper alternative to wool) and wool (the premier carpeting option and the only natural fibre used in manufacturing carpets).

Do you have existing floorboards and wish to fit new solid wood floor over it? If you’re planning to go for a DIY effort, there are a number of things you should put into consideration before you even get started. Firstly, you should have it in mind that existing softwood floorboards are usually not flat, implying that the surface of the existing might not be ideal to serve as the foundation on which to put your new solid wood flooring. Secondly, if you’re going to lay the new solid floor on the existing floorboards, it would be wise to select wood that is a minimum of 18mm thick to make your new solid wood flooring a lot more stable.

If you discover that your old floor is not too even, there are two option you can consider to protect your investment. You can lay the new floor at a 90 degree angle over the existing one. In other words, you should lay the new floor lengthways if the old one is laid widthways. Using this technique alongside a method of fitting referred to as secret nailing will go a long way to make sure your installation efforts is a successful one.

The second option you can put into consideration when laying solid wood flooring over old ones is to lay chipboard or plywood over the existing floor prior to the installation of the new floor. Here, there will be an increase in the cost of your installation, however it will be more reliable and durable as it assists in ensuring the stability of your new flooring. Some benefits that comes with this option includes the freedom to lay the new solid wood flooring in any direction you want as well as the freedom to use any fitting method you deem fit. Click here to learn more about wood flooring.

How To Lay Wood Flooring

Laying of wood flooring is actually a very simple task contrary to many beliefs. First and foremost, before commencement of the fitting process, you must determine the direction you would like the engineered wood flooring to lie in. To do this the right way, they should lie in the direction of the the longest wall. However, if your subfloor is wooden, then having the boards positioned across the joists underneath would be your best bet to get started.

Here are some simple steps to follow to properly lay your wood flooring:

• Start from a corner, working from left to right and place the initial rows of the boards with the groove’s end directly opposite the closest wall.

• Make use of expansion spacers. Place them in between the wall and the board alongside an expansion gap of about 8 to 10mm.

• Place the board’s final rows at about 100mm wide. To achieve this, it is crucial to be pro-active with the measurement and cut the boards (if you deem fit) to adjust the first row.

• With the help of the click system, the boards will click together.

• Fit in the next board. Ensure to attach the tongues together (30 degrees from the floor) and once done, you can proceed to lower and lock it in place. Do this till you get to the end of the row.

• Cut the last board of the row to size if its too long.

• If the part cut off is up to 300mm, simply use it to start the next row. If not, cut a new board in half to use.

• Put the rows side by side in such a way to ensure the joints are staggered at each and every row. Keep a consistent gap between the wall and the planks via the continuous use of the spacers.

• Lay a plank over the last row to determine the width of the previous board. Position a new plank in a way that its tongue is directly against the wall. Once done, proceed to mark a line of plank underneath to get the required width. Then, fit the plank into the space with the help of a pull bar and hammer.

Click here to learn more about wood flooring.