Find an Electrician you can trust in Bagshot.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

Are you thinking about installing a solar thermal system in your home? If yes, the you’d most likely be wondering the exact amount the system is going to cost. Well, you’re not alone. This is one of the most common question when it comes to solar thermal systems and we aim to answer that in this article. So let’s get started!

Unfortunately, the cost of a solar thermal system can’t be given in a single, accurate answer as they vary widely. However, when getting a new solar thermal system, you can expect to pay a sum within the range of £3000 to £6000 ( this includes a lowered VAT rate of 5 percent). The figures provided takes into account the installation costs as well as all the parts ( such as control panel, solar collectors, hot water tank and pipes).

To determine the price of your system, the quality and type of the panels matter. For instance, according to the Solar Trade Association, a properly insulated twin coil cylinder system would be priced at around £4500. in the same tone, it’s also possible to get DIY solar thermal kits that includes all the required hardware which will cost within the range of £1500 to £250. This however, may not be eligible for government support. In order to benefit from the RHI, your system must be fitted by a MCS accredited installer.

The varying prices of the solar thermal system’s initial cost is based on the specification of each individual house. For example, in situations where the building is having complicated water system, the plumbing cost is expected to increase which will have a serious impact on the overall cost of the solar thermal power system.

Most people want to connect solar panels to a battery when they’re not at home all day to use the electricity they generate, or generate more than they consume over a day. Solar batteries are a great way to maximise the savings on your energy bills since you can use every unit of electricity you generate.

If you want to connect your solar panels to a battery, the best – and safest – way is to ask an MCS-registered company to do it for you. They’ve had lots of training and hold qualifications in handling electricity and installing solar batteries, so they will be able to recommend the best battery for your solar panels and for the among of electricity you use. Some of the brands they might recommend include Tesla, SolarEdge and SolaX, but there are many more to choose from. If you want to send electricity to the grid from your battery to receive Smart Export Guarantee (SEG) payments, it’s also worth leaving installation up to a registered installer. This is because you might not be eligible for payments if your battery wasn’t installed by an MCS-registered company.

However, if you do want to have a go at connecting your solar panels to a battery, it’s worth finding out whether your system is ‘storage ready’. Most relatively new systems will be, since batteries are becoming more commonplace. If your solar panels are storage ready, they will have an inverter that can easily have a battery added to it. If this is the case, then you should be able to buy the solar battery you want and follow the manufacturer's instructions to install it.

But it’s worth remembering that electricity is extremely dangerous when handled improperly. If you don’t get the solar battery connected properly and something goes wrong, it could cause a fire or you could electrocute yourself. If a fire breaks out due to your battery, it’s unlikely that your home insurance company would pay out since you connected the battery yourself. That’s why it’s always worth speaking to a registered installer to install a solar battery storage system for you.

It might be possible to fit electrics in your shed, depending on where it is and what it’s made of. You should get in touch with a qualified electrician to find out whether it’s possible. Never attempt to run electrical cable from your house to an outbuilding!

It’s always recommended to use a certified electrician to carry out electrical work. They can self-certify that their work meets building regulations. While some parts of electric heating systems can be installed as a DIY project, the thermostat and other control wiring legally must be installed by a certified electrician. There are a range of competent persons schemes in operation.

The importance of selecting the right size battery for your home simply cannot be overemphasized. A lot of home and property owners are facing this challenge and understandably so. Selecting the right battery size for your needs depend on a number of factors which includes your motive for adding a battery, your electricity usage, your budget as well as your panel array size, be it new or existing. In this post, we’re going to take you through some of these factors to help you determine the right battery size for your home or property. Let’s take a look!

• Your motive for getting a battery. While most people purchase a battery to wipe out their need to purchase electricity from the grid with the hope of making some savings, others add a battery so as to enjoy backup power. There are also some who just needs it to power their home with solar energy. It’ll not be economical to size a battery to effectively take you off the grid, but if your motive is to make savings, then you’ll should expect to purchase some electricity from the grid during the year.
• Electricity usage. The average household uses about 16kWh of electricity on a daily basis. During the daylight hours, most of these household will use a third of their electricity when the solar panels are still generating electricity, while the remaining two third are purchased from the grid. In other words, you’ll require a minimum of 10kWh battery capacity if you were to use a battery to power the electricity you purchase from the grid.

For a typical British household, you’ll most likely need a 5kWh solar power system which normally generates about 17 to 21 kWh on a daily basis depending on your location in the UK.

With each year that passes, the amount of electric cars on the road keeps rising and with them comes a necessity to develop new infrastructures and also accessories like charging cables as well as connectors for easy sustainability. This concept is still pretty much new to the general public as most people still use vehicles that are fuelled by petrol and diesel. There are also some differences in design which asides from the lack of an engine underneath the vehicle’s bonnet, the way in which an electric car is filled up largely varies petrol or diesel powered vehicles. There’s a lot that people will have to learn about electric cars and even more so when it comes to their everyday use. One of the most common questions a lot of individuals ask about electric cars is whether all electrical vehicle chargers are the same. If you’re also looking for an answer to this question, then you’ve come to right place!

If you’re interested in getting an electric car, charging your vehicle at home may not generate any major concern but what about making use of the public charging system? This is when it gets a bit confusing because if you’ve never had to do it before you may worried about making use of the wrong charger on your car. So the question is, does every electric vehicles have the same plug? The answer is simple - there are different plugs and cables for varying electric vehicle brand as well as points of use. In general, you’d have to choose most suitable charging level for your electric vehicle.

If you’re thinking about installing a solar thermal system in your house, it’s always important to put into consideration numerous factors before you proceed. While some solar thermal systems are suitable for use at home, there are also some that are suitable for businesses or organizations which normally requires a big amount of hot water like hotels, restaurants, schools, hospitals and many more. You’ll also find some types available in the market that are suitable for communities to satisfy communal hot water demands.

It should, however, be noted that solar thermal systems do not have the capacity to produce all the hot water demand of a house. In the UK, an average household will need an annual water heating of between 3000kWh to 5000kWh. Whereas, a solar thermal system is only able to meet about 40 percent to 60 percent of this demand.

With that in mind, it’s also worth noting that during the summer months when the solar radiation is at its peak and hot water demand is relatively lower when compared to other seasons, a solar thermal system may be able to provide all of your household’s hot water needs. This implies that during this period you may not find the need to operate your boiler at all. However, during winter or colder months, when you have a higher hot water demands in contrary to a lower solar radiation, a solar thermal system will only be able to take care of about 20 percent of your household’s hot water needs. And that ultimately implies that during this period, you’ll need to rely more on a alternative or backup source of heat like gas, coal, electricity, oil or LPG.