Find an Electrician you can trust in Alresford.

The cost to charge an electric car in the UK varies between home, work and public charging.

For a typical electric car with a 60kWh battery and ~200 mile range:

• Charging at home: Costs about £9.20 for a full charge. *
• Charging at work: Many employers will install workplace charging points and typically offer free access throughout the day.
• Charging at public locations: Public chargepoints at supermarkets or car parks are often free to use for the duration of your stay.
• Rapid charging: Rapid charging points are normally found at motorway service stations and typically cost £6.50 for a 30 min, ~100 mile charge.

Charging an electric car at home costs about £9.20 for a full charge* and is the most convenient and cost-effective way to keep your car fully charged. Most drivers will charge their electric car overnight, waking up to a full battery every morning.

Average domestic electricity rate in the whole of the UK is about 17p per kWh.

Fully charging a 60kWh electric car will cost between £9.00 and £9.90 (depending on where you live) and give you about 200 miles of range.

* Costs calculated at 17p/kWh based on usable battery is ~54kWh (90%).

If you’re looking to install a solar thermal system in your home, this is usually one of the first concerns several homeowners have. Being fully aware that solar water heating systems are usually more expensive than their counterparts - the conventional water heating systems, the question arises whether or not you’ll be able to save some money from your solar water heating system in the long run. In this article, we aim provide an answer to this important question. Let’s take a closer look!

When it comes to solar thermal systems, the money you’ll be able to save in the long run depends on a wide range of factors. These factor includes:

✓ Your system’s performance.

✓ Your geographical location and solar resource

✓ Your household’s hot water demand

✓ Financing and incentive options that are available.

✓ The cost of fuel that’s being used for your alternative or backup water heating system, if you own one.

✓ The cost of conventional fuels such as oil, electricity or natural gas.

There are several benefits, however, that comes with the installation of a solar water heating system. Since the sun is absolutely free, future fuel shortages and price hikes will have little impact on you. Also, on the average if you decide to fit a solar thermal system your water heating bills is expected to drop about 50 percent to 80 percent. What’s more? The economics are even a lot more attractive when you’re just about to build a new home or refinancing. When you include the price of a solar water system in a 30 year mortgage, it’ll normally amount to very low price per month. Therefore, on a monthly basis you’ll be saving more and paying less.

What an electrical safety certificate offers both home and property owners as well as tenants is peace of mind. However, if you’re going to get an electrical certificate, you’d probably want to know just how much it’s going to cost. In this post, we aim to give you an idea of the electrical safety certificate pricing in order to help you make a budget and start planning. Let’s take a look!

Generally, the cost of getting an electrical safety certificate in the UK is usually within the range of £80 to about £150 for a medium sized home. With that in mind, it’s also important to note that the price you’ll have to pay to acquire an electrical safety certificate is based on a number of factors which includes the complexity of the job, the size of your property amongst many others. All home and property owners including landlords should invest in getting an electrical safety certificate. The certificate can only be legally issued by a qualified and certified electrician and it must document that all electrical appliances as well as connectors within a property are totally safe and in a proper working condition. What’s more? More often than not, an electrical safety certificate test will most likely be completed in less than 24 hours.

The Electrical Safety report bring to life an concerns as regards the status of all electrical appliances and circuits. At present, it isn’t a legal requirement for home owners. However for landlords, it is an obligation to acquire an up to date Electrical Safety Certificate.

If you’re a home or property owner planning to get an electric vehicle, having a Level 2 charger installed in your garage or near your driveway can go a long way to make charging really convenient for you. So if at all you want to take on this task by yourself, you should ensure to do it the right way. If you lack the confidence or skills required to pull this off, then we’d strongly recommend you hire the services of a professional who can guarantee the best results the first time. In this post, we’re going to provide you with an good insight on the home electric charger installation process. Let’s take a look!

• Determine the eligibility of your home. Make sure your home is eligible for a charger installation by consulting with your Technical Safety BC.
• Confirm you have sufficient electricity supply. Is there enough electricity distributed to your home to support an ev charger?
• Confirm that your electrical panel has enough space to accommodate a circuit breaker for the electric vehicle charger. If not, you’ll need to hire the services of an electrician.
• Get an electrical permit. Apply for an electrical permit with your municipality or Technical Safety BC.
• Charger installation. Proceed to fit the ev charger, but make sure a safety officer is on hand to examine your electrical work before you conceal any wiring or attach to a supply source. Then your electrician will have to complete the contractor consultancy form once the installation is done.
• Inspection. The inspection should be inspected by your municipality or Technical Safety BC.
• Apply for a rebate.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

If you’re thinking about adding new power sockets to your room, then you’ve come to the right place! This task can be a very tricky one especially if you don’t know how to go about it. If you don’t have the skills or experience necessary to pull this off, then we’d strongly recommend you hire the services of qualified and licensed electrician who can guarantee the best results for help. In this guide, we’re going to take you through the numerous steps you’d have to take to make sure your new power sockets is added successfully. Let’s take a look!

• All the power to the working area at the primary electrical panel should be turned off.
• Identify the cut area for individual electrical box.
• Pilot saw blade by drilling corner holes
• Drill into framing for wiring, if required
• Connect electrical wires to the electrical panel from the outlet box holes, pulling four feet through the wall.
• Attach white wires to silver screws as well as black wires to brass screws and also the ground wire.
• Incorporate electrical tape to tape around the box
• Connect the box to the wall and cover with the outlet plate
• Carry out the process for individual outlet needed
• De-energize the entire electrical panel by shutting off the house’s main breaker
• Fit an arc volt breaker by connecting white and black wire to the breaker
• Connect white wire from the new breaker directly onto the neutral bar of the electrical panel
• Finally, you can turn the main breaker back on.

What Are The Best Electric Radiators?

Being afforded options in life is what we all seek. However, when the options are obviously too much, it can have a negative impact - exactly the case with electric radiators. With so many electric radiators in the market today, identifying the best and most suitable one for your home can be less helpful and extremely confusing, and even more so when you don’t know what you want. In a world filled with a huge selection of electric radiators, some designed for general heating while others are designed for more specific purposes, where would you get started? Here we’ve put together some of best electric radiators which you can put into consideration when making a decision. Let’s have a look!

• The Rointe D Series

The D series is one of the most popular electric radiators you’ll in the market today and deservedly so.with an advanced controllability via the Rointe Connect App and TFT control panel, these series have been rightly marked out as the most sophisticated electric radiator till date. What’s more? It’s suitable for both small, medium and large rooms, as it heats from 3m2 to about 16m2. The installation and programming of the Rointe D Series is very easy as it also enables a full access to every functions included as well as consumption costs.

• The Dimplex Q-Rad

As a high end heater, the Dimplex Q-Rad is one of the most popular brands. It is designed for a large room as it can heat up an area of about 20m2. The electric radiator features simple controls, sleek and good looks and works automatically all day.

• The Haverland RCTTi

This is conveniently one of the most efficient and reliable electric radiators you’ll find around. It stands out with the possession of its Dry Stone technology which works to ensure the room is kept at the right temperature.

• The Stiebel Eltron CND

Featuring a combined radiant and convection heating, this dual heat source is a very good option for homeowners with a tight budget. It works excellently to store heat which it later releases. The electric radiator also sense when the windows are open and react intelligently to the environment.

• The power of your solar panel system – there's no point buying a higher capacity battery if your system will never generate enough electricity to charge it
• How often you think you will need to charge your battery
• Your budget
• Whether you care about having the latest technology and a recognisable brand name