Find an Electrician you can trust in Wadhurst.

If you’re thinking about adding new power sockets to your room, then you’ve come to the right place! This task can be a very tricky one especially if you don’t know how to go about it. If you don’t have the skills or experience necessary to pull this off, then we’d strongly recommend you hire the services of qualified and licensed electrician who can guarantee the best results for help. In this guide, we’re going to take you through the numerous steps you’d have to take to make sure your new power sockets is added successfully. Let’s take a look!

• All the power to the working area at the primary electrical panel should be turned off.
• Identify the cut area for individual electrical box.
• Pilot saw blade by drilling corner holes
• Drill into framing for wiring, if required
• Connect electrical wires to the electrical panel from the outlet box holes, pulling four feet through the wall.
• Attach white wires to silver screws as well as black wires to brass screws and also the ground wire.
• Incorporate electrical tape to tape around the box
• Connect the box to the wall and cover with the outlet plate
• Carry out the process for individual outlet needed
• De-energize the entire electrical panel by shutting off the house’s main breaker
• Fit an arc volt breaker by connecting white and black wire to the breaker
• Connect white wire from the new breaker directly onto the neutral bar of the electrical panel
• Finally, you can turn the main breaker back on.

If you’re thinking about rewiring your three bedroom house, one of the first few things you’d have to put into consideration is the cost of completing the project in order to help you set a budget and start to plan. In this post, we seek to provide you with the most accurate cost possible for your project to help you get started as soon as possible.

In truth, there’s no simple and short answer to this question as the average cost to rewire a house is based on a wide range of factors. For older properties, you may need completely rewire the property in order to enhance the energy efficiency. However, this may not be required the your home was just recently built. Firstly, it should be stated that there are numerous factors that affects the price of a rendering a house which includes the size of the house and its condition, the ease of access, the prep work required, as well as your location and the quality of the contractor your hire. Out of all these factors, the most significant variables are probably the type of rewiring task you go for (whether for the whole house or some specific parts ) as well as the size of the house.

House rewiring is usually a messy and disruptive task which can also be very dangerous especially when handled by a inexperienced individual. As a result, we’d strongly recommend that this task is carried out by a qualified and registered electrician who is well trained to perform this task to perfection. The average cost for electrical rewiring for a three bedroom semi detached house should be within the range of £3000 to £4500, although there may be some extra house rewiring cost that may also arise in the process.

How To Install Solar Panels And Batteries

Have you decide to purchase a solar system for your home and wondering how to go about the installation? If yes, then we’ve got you covered! In recent times, it’ll be totally safe to say that solar panels and batteries for home use in the UK has now become more of a necessity than a luxury considering the numerous benefits the system offers. However, with the cost of having the system installed, you might be forced to think about the doing the installation yourself.

If you lack proper training and experience in the solar system installation process, it’s advisable to hire the services of a qualified technician who can guarantee the best results the first time and help you save time and extra costs that may result from possible costly errors. Here, we’ll give you a good insight into the installation process.

• Mount the solar panel and ensure it’s properly screwed to your roof. Try to position in such a way that it faces direct sun rays to have enough solar power generated.

• Connect your charge controller. The current that’s being generated by the solar panels will not be stable all day long. As a result, it’s important to avoid connecting solar photo voltaic modules directly to your better, if you don’t want it damaged. To control the current received from the solar panels, the charge controller is required. It has three connecting points - one for the battery, one for the solar panels and the last for Direct Current (DC) identify the one for solar panels and connect accordingly.

• Connect the battery to charge controller. The charge controller possess two terminals for the battery - the positive and negative terminals. Connect the positive terminal to the positive of the battery and also do the same for the negative.

You should report any suspected faults to your landlord as soon as you know about them. It is their responsibility to investigate, and hire an electrician to do any work if needed. Know your obligations as a tenant and keep in touch with your landlord on a regular basis.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

If you’re thinking of adding a solar battery to your home, you might be wondering whether or not it’s going to work in a power cut. If yes, then you’re not alone as this is one of the most common questions asked when it comes to solar batteries. In this post, we aim to provide you with a detailed answer to solve this concern once and for all.

The answer to this question is, it depends. The main reason why your solar batteries will usually not work or provide your home with the much-needed back up power is as a result of the several threats it poses. You should be aware that both your solar panels and battery are connected to the main grid. When a power cut occurs, your engineers will have to operate on the grid. If the solar panels or batteries are in operation at the period there’s a high chance the engineers would be electrocuted by the electricity that’s being produced. As a result of this, solar inverters are usually designed to automatically switch off once a power cut occurs. However, it should also be noted that if your solar battery possesses backup functionality, you’ll be able to make use of your solar energy in the event of a power cut. In other words, what determines if your home battery would work in a power cut is the availability or otherwise of a backup functionality.

Furthermore, you might also wish to know if your solar panels will continue to charge the battery in a power cut. Well, this depends on the type of backup system you possess. There are some more affordable batteries that are designed to automatically release their stored energy upon the detection of a power cut. And this is mostly because the battery inverter is usually smaller than the solar inverter which allows the energy from the solar inverter to the transmitted to the battery - risking an overload. However, if otherwise, then energy can continue to be transmitted to the battery until its fully charged.

There’s a need to ensure that all the paperwork are in place,before putting your house up for sale on the property market. An very good example of such essential document is the Electrical Installation Certificate (EIC) which is used as a proof to attest to the fact that the electrical installation works carried out on the property in question was actually done and also whether or not it satisfies the building regulations. It’ll be a contravention of the law to put your house up for sale or actually sell it without producing this important document. Therefore, if you’re looking to sell your house you may wish to know the electrical documentations you need to complete the task. In this post, we aim to provide you an in depth insight into the electrical certificates needed to sell your house while also helping you make informed decisions along the process. Let’s take a look!

You’ll need to obtain two certificates in the event whereby the electrical work done was performed by a registered and qualified electrician. The two documents include:

• The Building Regulations Compliance Certificate - This is provided to confirm that the electrical works done complies with the Building regulations.
• The Electrical Installation Certificate (EIC), alternatively you can have a Minor Electrical Installation Works Certificate which is provided to confirm that the electrical works done satisfies the BS 7671.

In addition, the local building control body must be provided with a copy of these documents. In such an event whereby the electrical work was completed after 2013 and either it was done by yourself or by an individual who isn’t a registered professional, then there’s a need to make sure that work is inspected by a registered third party certifier within 5 days of completion. If the work is found to be satisfactory, you’ll be issued a copy of an Electrical Installation Condition Report.