Find an Electrician you can trust in Verwood.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

Home electrics can be extremely dangerous and it’s very unwise to try and carry out repair work or maintenance yourself without the necessary knowledge and skill. Therefore we would always recommend using a Part P registered electrician at all times.

You can find out roughly how old your wiring is by simply looking at it. If the wiring around your fuse box is covered in old-fashioned casing, or is damaged or fraid, it may be over 25 years old and need replacing. This is more common in older properties or houses that have been empty for long periods of time.

An electrical safety inspection is basically the act of carrying out a thorough assessment of all electrical systems within a property, be it residential, commercial or industrial premises. The main goal of conducting this survey is to see to the fact that all the electrical systems and installations forming part of a property are correctly fitted, well maintained and ultimately, safe. This is required to be carried out by an electrician who’s an approved contractor and accredited by ECA, NICEIC or STROMA. To get contractors who can carry out the electrical safety inspection and meet with the government criteria, you simply have to search on the Electrical Component Person database. They’ll assess the current condition of the electrical systems and evaluate if they are working efficiently while also paying special attention to any defects or faults.

Generally, the best way to get an electrical safety certificate ( an EICR) is to shop around. In the event whereby you need the inspector to examine a part of your property you’d have to raise his/her awareness to this. This will be referred to as an “agreed limitation in the report.

Failure to comply with electrical safety regulations bring about serious penalties for such landlords. Upon the introduction of the new regulations in June 2020, local authorities can fine the electrical safety regulations-breaching landlords up to £30,000. Asides this fact, it’s also in your interest to keep your property as well as its appliances in a good condition at all times. If everyone including your tenants feel safe and your property is in great shape, everyone is happy!

The cost of an Electrical Certificate varies depending on the size of your home as well as the number of electrical installations and appliances that needs to be checked. The price can start anywhere from £120 and above.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

Also commonly referred to as a consumer unit in recent times, a fuse box is responsible for controlling and allocating of the electricity in your home. They hold the power any time there’s an overload in one of the circuits which in turn, prevents fire as well as electrical damage. Fuse boxes are often incorporated in homes but consumer units are very rapidly replacing them. Therefore, when your fuse box breaks down, it’s always a smart decision to replace them with consumer units due to the fact that they’re safer and also comply with building regulations while also being a lot easier to use. If you’re extending your home, upgrading to a larger capacity model enables you to make use of more power with the power overloading. In this post, we’re going to cover the amount you’re expected to pay to replace or install a new fuse box or consumer unit as well as the factors that may affect the cost.

For a 10 way dual RCD consumer unit, the typical cost range will be between £250 to £600, meanwhile 15 way dual RCD consumer unit should cost within the range of £300 to £700. Overall, the smaller the house, the fewer the circuits that’ll be needed, hence the difference in the aforementioned prices.

There a number of factors that can affect the cost of replacing a fuse box. These factors includes the the size of the house in question ( the bigger the house , the more the circuits there are and the bigger the fuse box needed), the location ( for instance, places like London where there are higher demands are likely to be more expensive than other regions ).