Find an Electrician you can trust in Marazion.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

What Size Of Electric Boiler Do I Need?

If you’re thinking about installing central heating in your home or property, you’ll be shocked by the plethora of options that’s currently available in the market as regards the boiler type that can be installed. Being a very good alternative to gas boilers or an oil or LPG boiler, electric boilers are here to stay. They usually feature different power outputs which tends to lead to one of the most frequently asked questions about electric heaters - what size of electric boiler do I need? Here, we’ll give you a good insight into sizes of electric boilers available to help you make the right decision.

The importance of getting the perfect size of electric boiler for your home can not be over-emphasized. If your electric boiler size is too small, it won’t be able to provide the level of heat and hot water required. And on the other hand, if it’s too big, it’ll definitely consume more electricity which would be a total waste of money.

To determine the correct size, if you have a wet central heating or water radiators in your home, you’ll need to calculate the boiler’s capacity required to operate them and allow 1.5kw per radiator. To be more accurate, it’s advisable to talk to a professional installer to avoid making a costly mistake. Every professional installer should have an idea of the appropriate size of electric boiler that’ll be needed given your special requirements and home size.

Generally, with a 12k kilowatt boiler, you should be able to operate up to 7 to 8 radiators which is good for smaller properties. For apartments and flats, getting a smaller electric boiler would be the best option.

It might be possible to fit electrics in your shed, depending on where it is and what it’s made of. You should get in touch with a qualified electrician to find out whether it’s possible. Never attempt to run electrical cable from your house to an outbuilding!

There are two different types: flat plate, where lots of thin tubes carry water through a flat absorber panel, and evacuated tube, where vacuum glass tubes capture the sun’s energy directly. There is little difference in performance between the two but evacuated tube panels do more obviously extrude from the roof.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

Like every other systems in your home, solar hot water systems will require periodic inspections as well as a regular maintenance in order to keep it running as efficiently as it should. Not only that, the various components will also require either repair or replacement from time to time. It’ll also be proactive to take the necessary precautions so as to prevent worrying issues like corrosion, scaling or freezing.

Is it a task you can handle on your own? Well, there are some inspections and maintenance activities you should be able to handle on your own, however, you’ll also require a qualified technician to carry out the more technical or complicated tasks. You should also take note that it may actually be more cost effective to have some systems replaced, shut off or removed completely than having it repaired. Here are some of the essential inspections that should be carried out on solar system components. They include:

✓ Collector soiling. Periodic cleaning of your collectors is important especially in dry and dusty climates.

✓ Plumbing, ductwork and wire connections. Check the pipe connections for fluid leaks. Examine duct connections and seals. Also make sure that all wire connections are tight.

✓ Roof penetrations. Flashing and sealant around the roof penetration should be checked to see that it’s in a good shape.

✓ Collector shading. Check for shading of the collectors on annual basis as this may greatly affect their performance.

✓ Support structures. Examine all bolts and nuts which connects the support structures to the collectors for tightness.

✓ Heat transfer fluids. Anti freeze solutions in liquid solar heating collectors will have to be replaced periodically. And this right here is a task that’s best handled by a licensed technician.

Can You Replace A Gas Boiler With An Electric Boiler?

In the UK, there are about 22 million households that are heated with the use of a gas boiler. However, do not assume that they’re the best type of boiler to install. The fact is, if your house isn’t connected to the main gas supply, the best option is for you to install an electric boiler rather than a gas boiler. So is it possible to replace a gas boiler with an electric boiler? The simple answer is yes. Both heating system options work in varying ways and also with a different impact on the environment.

The gas boiler is able to generate heat with the help of a gas burner. A heat exchanger is linked to the burner and heats the water available in its chamber. The hot water is then supplied to the heating circuit.

However, the thing is that natural gas can actually be more affordable when compared to using electricity to operate your boiler, but they have a negative impact on the environment. This is because gas boilers make use of an odourless, colourless and poisonous gas - carbon monoxide.

Meanwhile electric boilers are powered by electrical energy, hence, no carbon monoxide leak risks. Instead of using gas to heat up water, electric boilers distribute energy to heating elements which, in turn, heats up the water. So thinking about what’s best for the environment, you’d go for electric boilers. However, they’re more costly and are not as efficient as oil boilers.

If you reside in a smaller house that’s not connected to the main gas supply, then you might want to consider installing an electric boiler. However, if you live in a larger house, an electric boiler may not be the best option as they’re mostly designed to generate little quantity of hot water.