Find an Electrician you can trust in Radstock.

Unlike in houses built in the 1970s where a good majority of the houses will not need to be rewired, for houses built in the 1960s you’d probably need to rewire the entire house unless the wiring is the modern PVCu coated type. Generally, the homes built especially in the 1960s and 1970s brought about enormous changes. This is because over the years our way of living began to change and as a result, our need for electricity became even greater. In response to this, the electrical systems we incorporate needed to change in order to match the new set standards.

In the 1960s, the amperage normally used was increased to 100, which enables home and property owners to power their dishwasher, microwave as well as refrigerator all on one circuit. However, while this may be a remarkable improvement for our grand parents, this is just enough to cater for our modern day appliances. In recent times, new homes are constructed using a wide range of dedicated circuits due to the fact that each of our appliances makes use of much more electricity to function. Consequently because the 100 amp panels of the 1960s possessed restricted space for breakers, home and property owners who still had the units in their homes will inevitably require a sub panel or a new panel entirely - meaning a total rewiring of their property.

Furthermore in the 1960s, builders turned to aluminium from the previously used copper as it was a great conductor and also happens to be relatively cheap. However, after a couple of years a host of electrical fires cropped up in houses that are wired using aluminium. It was later discovered that when the switch to aluminium was made, the light switches or receptacles which were originally made for the previously used copper was overlooked. It was learned that there’s a corrosive chemical reaction that arises as a result of the two dissimilar metals when connected. Hence, the more reason why aluminium wired houses in the 1960s needs to be rewired.

Tesla’s top-of-the-range battery storage system is still one of the most expensive on the market. It has a huge 13.5kWh usable capacity and can even keep you up and running during a power cut. But how long does a Tesla Powerwall battery last? And does this mean it’s worth investing in one?

The Tesla Powerwall 2.0 comes with a 10-year warranty. But Tesla says that it should last way beyond this – at least 5 years longer. The standard warranty says that it should work at 70% capacity for the full 10 years – so if it loses more than 30% of its storage capacity within that time, it should still be covered.

While the Tesla Powerwall does last a long time, it has a large capacity that most average households won’t require, and it’s a costly option. After installation, the Powerwall 2.0 will set you back between £6,500 and £9,000, so ideally you want it to last past its 10-year warranty.

Before you splash out, consider the size of the solar panel system you want to install or you already have. Will it generate enough electricity to make it worth storing in the Powerwall? If not, are you expecting to upgrade your solar panels to a larger system in the future? If you are, then it might be worth investing in a Powerwall. It might also be better to wait until you come to upgrade your solar panels – the solar battery price trend is going the same way as solar panels, so they will probably continue to decrease in price as more people adopt the technology.

Are Electric Radiators Expensive To Run?

Just like many home additions, the running costs of electric radiators varies largely on a number of factors. Great number of electric radiators typically comes with an in built thermostat which is designed to turn itself off automatically when not in use in order to save energy.

However the energy provider’s set electricity charge tariff will also have a great influence on an electric radiator’s running cost. Let’s take a look at the running costs of an electric radiator!

A 600 Watt electric radiator ( on a standard electricity tariff) will usually have a running cost ranging between 4 to 6 pence each hour. However you should also take note that this scenario might change in situations whereby the electric radiator is not calling for heat the full 60 minutes of each hour. And this is more likely to be the situation as the thermostat is programmed in such a way that enables it to turn itself off immediately there’s an achievement of your required room temperature level - usually within 10 minutes from the time it was switched on. As a result of this, the running cost per hour of electric radiators will be greatly reduced to just about 1 to 2 pence.

It’s also important to note that enhancing the insulation of your home can go a long way to add to the heat retention value of each room. Consequently, the duration at which the electric radiator calls more heating will be significantly reduced, which in turn, implies a lower electricity bill.

Another key factor that can play a huge role in saving on your heating bills is the programming as well as usage of your electric radiators. Every radiator comes with an independent digital thermostat with a number of 24/7 programming options to help achieve maximum efficiency. When the radiator is properly set according to your lifestyle, you can save as much as 50 percent on your heating bills.

If you’re thinking about installing a solar thermal system in your house, it’s always important to put into consideration numerous factors before you proceed. While some solar thermal systems are suitable for use at home, there are also some that are suitable for businesses or organizations which normally requires a big amount of hot water like hotels, restaurants, schools, hospitals and many more. You’ll also find some types available in the market that are suitable for communities to satisfy communal hot water demands.

It should, however, be noted that solar thermal systems do not have the capacity to produce all the hot water demand of a house. In the UK, an average household will need an annual water heating of between 3000kWh to 5000kWh. Whereas, a solar thermal system is only able to meet about 40 percent to 60 percent of this demand.

With that in mind, it’s also worth noting that during the summer months when the solar radiation is at its peak and hot water demand is relatively lower when compared to other seasons, a solar thermal system may be able to provide all of your household’s hot water needs. This implies that during this period you may not find the need to operate your boiler at all. However, during winter or colder months, when you have a higher hot water demands in contrary to a lower solar radiation, a solar thermal system will only be able to take care of about 20 percent of your household’s hot water needs. And that ultimately implies that during this period, you’ll need to rely more on a alternative or backup source of heat like gas, coal, electricity, oil or LPG.

How Much Does Pat Testing Cost?

When it comes to Portable Appliance Testing (PAT) there’s no particular rule that determines how much such services can cost. However as a rule of thumb, you should take note that when calling in a professional PAT testing company they’re likely to charge within the range of £1 to £3 per appliance that’s going to be tested. However, if you have quite a number of appliances to be tested, then there’s a good chance that the price per appliance can be reduced to serve as a bulk discount. So the more the appliances to be tested, the better.

There are companies that actually offer a pricing that’s below £1 per item, however companies likely are most definitely going to have a fixed minimum number of appliances that are required to be tested or a fixed minimum fee like 60 portable appliances. It must, however, be noted that pricing can also go beyond PAT Testing as several professional companies will add some additional advantages which is more than just the test of each individual appliance. This kind of pricing can include other services such as a thorough visual inspection, plug rewiring as well as fuse replacements. They can also include stuffs like Pail and Fail labels in the pricing.

Generally, the average price of PAT testing will be based on various influencing factors such as the type of the appliance, setting, number of appliance to be tested as well as other related expenses. What’s more? Most PAT companies will offer a company with a PAT Testing Certificate so as to certify that the company is in total compliance and also remains a safe environment to work.

There’s a need to ensure that all the paperwork are in place,before putting your house up for sale on the property market. An very good example of such essential document is the Electrical Installation Certificate (EIC) which is used as a proof to attest to the fact that the electrical installation works carried out on the property in question was actually done and also whether or not it satisfies the building regulations. It’ll be a contravention of the law to put your house up for sale or actually sell it without producing this important document. Therefore, if you’re looking to sell your house you may wish to know the electrical documentations you need to complete the task. In this post, we aim to provide you an in depth insight into the electrical certificates needed to sell your house while also helping you make informed decisions along the process. Let’s take a look!

You’ll need to obtain two certificates in the event whereby the electrical work done was performed by a registered and qualified electrician. The two documents include:

• The Building Regulations Compliance Certificate - This is provided to confirm that the electrical works done complies with the Building regulations.
• The Electrical Installation Certificate (EIC), alternatively you can have a Minor Electrical Installation Works Certificate which is provided to confirm that the electrical works done satisfies the BS 7671.

In addition, the local building control body must be provided with a copy of these documents. In such an event whereby the electrical work was completed after 2013 and either it was done by yourself or by an individual who isn’t a registered professional, then there’s a need to make sure that work is inspected by a registered third party certifier within 5 days of completion. If the work is found to be satisfactory, you’ll be issued a copy of an Electrical Installation Condition Report.

It’s always recommended to use a certified electrician to carry out electrical work. They can self-certify that their work meets building regulations. While some parts of electric heating systems can be installed as a DIY project, the thermostat and other control wiring legally must be installed by a certified electrician. There are a range of competent persons schemes in operation.

If you’re thinking about adding new power sockets to your room, then you’ve come to the right place! This task can be a very tricky one especially if you don’t know how to go about it. If you don’t have the skills or experience necessary to pull this off, then we’d strongly recommend you hire the services of qualified and licensed electrician who can guarantee the best results for help. In this guide, we’re going to take you through the numerous steps you’d have to take to make sure your new power sockets is added successfully. Let’s take a look!

• All the power to the working area at the primary electrical panel should be turned off.
• Identify the cut area for individual electrical box.
• Pilot saw blade by drilling corner holes
• Drill into framing for wiring, if required
• Connect electrical wires to the electrical panel from the outlet box holes, pulling four feet through the wall.
• Attach white wires to silver screws as well as black wires to brass screws and also the ground wire.
• Incorporate electrical tape to tape around the box
• Connect the box to the wall and cover with the outlet plate
• Carry out the process for individual outlet needed
• De-energize the entire electrical panel by shutting off the house’s main breaker
• Fit an arc volt breaker by connecting white and black wire to the breaker
• Connect white wire from the new breaker directly onto the neutral bar of the electrical panel
• Finally, you can turn the main breaker back on.