Find a Builder you can trust in Solihull.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

After making the decision to refurbish your home or property, the next obvious step is finding the right builder to get the job done. The process of getting a good and reliable builder can be a very tricky one especially when you don’t plan ahead. And in truth, the outcome of your house refurbishment project can only be as good as the contractor your hire. Consequently, finding the perfect builder for your task should be a top priority to get the best return on investment. Here are a few sources that will put you in the right direction to finding a reliable home refurbishment company.

✓ Friends, Relatives & Neighbours

If you have a friend, relative or neighbour that have recently completed a home refurbishment project, you can go for a visit to check out the work done. If you’re pleased with the work, you can proceed to ask about the work ethics of the builder and get the contact if satisfied.

✓ Internet

With the rapid rise of online technology, there’s hardly a service you can’t find on the internet. Websites like HomeAdvisor have been helping people find their desired service providers with relative ease for so long. To get the right building contractor online, it’s advisable to check reviews as well as testimonials before moving forward. Nowadays, you’re most likely going to find so many positive online reviews as some businesses now go to the extent of dubiously writing good reviews for their companies. As a result, it’s recommended to pay closer attention to the negative reviews and check if it’s something you can cope with before hiring a contractor.

✓ Store Contact Lists

You’ll discover a long list of building contractors on several stores trading building materials. These builders may not be affiliated with the store owners, but many stores see it as their responsibility to point you in the right direction so that the building materials acquired from them can be put to good use.

When it comes to house renovation costs, nothing is certain. As a rule of thumb, you should always expect the unexpected. Unforeseen circumstances (mostly unfavourable) can crop up from anywhere, at any time, greatly affecting the cost of the project. However, if you’ve completed proper planning and done your due diligence on your property before commencement, there’s absolutely no reason why you can’t put the works on budget.

The cost of a house renovation project depends on a lot of variables. These variables include the type of property you’re undertaking as well as the amount and complexity of the entire project. What’s more? Whether you decide to do some of the work yourself or wish to hire quality tradespeople to cover the entire project will also tell on the cost of the home renovation.

In the event whereby you wish to completely gut your property and begin from square one, here are some of the cost you’re most likely going to incur:

✓ Planning applications and building controls

✓ Architect’s design and specifications

✓ Contractors and build costs

✓ Snags as well as unforeseen problems

What will be the biggest cost, which will be determined by the amount of work you need done, is most likely going to be the structural and building work, which can reach up to tens of thousands of pounds.

Asides from material and labour, the administrative costs is another important cost you’ll need to factor in. The first thing here is usually insurance, this is because all regular building insurance policies does not cover large scale renovation projects. So if what you’re planning is a huge structural change to your property, then it’s more likely that it won’t be covered by your buildings insurance policy. In this event, you’ll have to take out a specialist renovation insurance.

It can be very hurtful when you’re looking to get a house and then identifies one that’s almost perfect, but that one thing that’s lacking is significant enough to prevent you from making an offer. For instance, you may like neighbourhood, the lot’s size, the number of bedroom and lots more. However, the only thing that’s holding you from making an offer is the outdated kitchen. This is the point where you wonder whether a mortgage can include the cost of renovation. In this article, we’re going to give you a good insight into this and more. Let’s have a look!

One of the major things your lender will put into consideration when you apply for a mortgage is the price of the property in question. For instance, so you’ve found your “almost perfect home for let’s say £400,000 and the cost of your intended renovation work runs up to about £150,000. In this event, you’re definitely going to find lenders who wouldn’t be too keen to let go of their cash. And that’s mainly due to the fact that lenders are only able to afford you, at best, 95 percent of the purchasing price. In other words, if you really want the house, you’ll have to finance it yourself no matter how much potential you think the house possesses.

This, however, does not mean that you can’t find some mortgage lenders who’ll allow for building costs. They exist, but this will mostly take place when the work is complete and the property is revalued. You may also be lucky enough to get a purchase plus improvements mortgage which allows you to renovate now and pay off the renovations over time at a better interest rate than other loan types.

When it comes to extending a home, the rear of the house often comes to mind a lot more than the front. However, this doesn’t mean that you can’t extend the front of your house. This can be done either as part of a renovation project whereby the entire house is incorporated or it can also be done in isolation. It’s possible to extend the front of your house without the need to apply for a planning permission, however, there are a bunch of limitations you’d have to comply with if you wish to carry out with such a project. Sometimes, this may imply that extending to the front of your home is more tedious and tasking than extending your home’s rear. So exactly how far can you extend the front of your home without planning permission?

The short and simple answer to this question is 2 metres square area with a height not more than 3 metres. Generally, you do not need a planning permission to build a front porch as long as its area doesn’t go beyond 2 square metres from a public road or walkway. Also, a tiled or slated roof can be as much as 4 metres but other roofs must not go beyond 3 metres in height. If you want to extend the front of your home beyond the restrictions specified, then you’ll have to apply for a planning permission.

Extending the front of home can be quite costly, but this can be controlled by not building to the extension to the highest specification, not including an extension on kitchens or bathrooms and more.

With the title of this blog, do not be deceived into thinking the purpose is to encourage you to install an external insulation by yourself. Even as a competent DIYer, it’s not advisable to buy a couple of materials and start slapping it into the wall hoping for the best outcome. External insulation is by no means a DIY job and without the proper training and experience, it can easily turn out disastrous resulting in loss of time, effort and money in such a valuable project. This blog, however, will give you a great insight on how the installation process works and help maximize knowledge ensuring you do not spend more than necessary.

External Insulation Installation

lRender Test

• This is done to ensure the existing render is good enough for insulation support.

• If positive, the insulation can be applied directly onto it.

• If negative, ensure removal of the old render before fitting the insulation.

lPipework Adjustment & Removal

• Remove all pipework prior to insulation fitting

• Install temporary downpipes to ensure water is not wasted and everything continue to function normally during the insulation fitting process.

lWindow Protection

• Protect the window with a protective layer or film.

lStarter Track Fitting

• Determine level you want the insulation to start (height).

• Fit the aluminium start track or carrier tray at the identified level.

lInsulation Boards Fitting

• Apply a layer of adhesive to the board and glue them to the wall in a staggered pattern.

• Cut to fit round all obstructions and windows.

• File off the edge of the board where necessary using a rasp upon successful fitting of the boards

lMechanical Fixing Inclusion

• Hammer around 10 fixings per square metre into the board.

• This is to secure the insulation boards.

lBeading Fitting

• Add corner beads and stop beads to ensure the insulation is secure and to prevent it from making contact with other materials.

lReinforcing Mesh & Render Addition

• Apply two layers of strengthening properties and between the two layers of render, include a fibre glass mesh.

lPrimer Application

• Paint on the primer

lFinal Render Application

• Choose your most preferred texture and colour as this will be the last coating of the installation process.

lPipework Re-installation

• Re-install all detached pipework at the start of the installation process.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

How Much To Board A Loft?

If you stay in a building where the space meant for storing stuffs is not sufficient, boarding your loft may be just the perfect solution for you. In several homes, the space is already present, and all you have to do is to make it more usable by boarding it out. This is unarguably one of the easiest and quickest ways to create storage space in your home.

Boarding a loft comes with a number of special benefits which includes:

• Assisting to declutter our living spaces and makes for a more spacious home.

• Creating a usable space whereby all seasonal items can be stored.

• Assisting to reduce heating bills as it prevents the loss of heat. When your loft is well boarded and insulated, it’ll help trap heat and prevent it from escaping via the roof.

• Adding to your home’s value by making your attic a very useful space for storing items.

• Helping to create a quiet space which can used for relaxation or getaway purposes and of course, this will require a bit more structural work.

So now that you’ve learnt a few of the benefits associated with boarding a loft, how much will it cost to have one made? This depends on an array of factors which includes the size of the space needed, the type of materials and labour cost.

Overall, a standard semi detached building will feature a lot of space of about 40 sqm to 50 sqm in size. There’ll be a need to add to the height of the floor joists before installing the chipboard decking boards. This job size should cost within the range of £1,000 to £1,500. It’ll require just a two-person team that are fully equipped and well versed about the processes.