Find a Builder you can trust near you.

Generally, a paved driveway is always subjected to regular usage and yours isn’t likely to be an exception, otherwise you won’t be here. Regular usage automatically necessitates regular maintenance of the driveway in order to extend its lifespan, make your property safer and add more value to it. This maintenance will involve a frequent inspection of the paved driveway so as to identify and repair divots, cracks as well as rutting. Paved driveways usually have a lifespan ranging between 15 to 20 years, but this can only be guaranteed when backed by regular maintenance activities. Failure to provide your paved driveway with a regular maintenance will lead to a rapid deterioration within just a couple of years after installation.

The issues commonly faced by paved driveways is usually different based on several factors such as the weather, your location, your property’s sub base as well as some other elements. The ability to identify the problems and solve or repair them on time is key to success while it’s also save you some time and money. In this article we’re going to look at how to go about do-it-yourself tasks that involves minor cracks. More intense damages are advised to be handled only by professionals.

✓ Prepare the area. Clear the debris, weed the plants or vegetation (if any).

✓ Use a strong spray from a garden hose to wash clean the cracks

✓ In the event whereby the crack is deep, simply fill it until it reach about a quarter inch of the surface with sand.

✓ Tamp down the sand to make it more compact.

✓ Apply a patching compound to the surface of the cracked paved driveway.

✓ Leave it for some time to cure.

✓ Once cured, you can then apply your sealant.

Do I Need Planning Permission For A Loft Room?

The answer to this question is maybe. Generally, loft rooms are covered under “Permitted Development which means you won’t need to apply for a planning permission to build a loft room. This is like an advance planning permission provided by local authorities to allow some particular building works to be done such as loft conversions, rear extensions and more. When you’re covered by a “Permitted Development, you’re given the free range to oversee your home’s development without much interference from the regulations or the council. However, for permitted development to apply, there are some specific criteria that must be met. Therefore, if your loft room does not meet the following requirements given below, then you must complete a planning application before proceeding.

• In a terraced house, the converted loft space must not be more than 40 cubic metres.

• In a detached building or semi detached house, the converted loft space must not be more than 50 cubic metres.

• The existing roof slope at the front of the house must cover the extension made.

• The extension should not increase the height of the roof in any way.

• Verandas, balconies and any other structures of this nature must not be included in the extension’s plan.

• The side facing window openings should be at a minimum of 1.7 metres above the ground. The windows must be obscured as well.

• The roof extension should be set back as far as practically possible. It should be at a minimum of 20cm from the current eaves.

• The roof extension should not overhang the house’s roof or it’s wall.

• The materials to be incorporated must be the same or at least similar to what you already have on the house’s exterior.

How To Put Up Plasterboard

Putting up a plasterboard is a vital process when it comes to home renovations. However as daunting as it may seem, with a good guide and regular practice you can master the skill within a small period of time. If you lack proper training and experience, we’d recommend you hire a seasoned professional plasterer for help so as to get the best result and also avoid additional costs due to possible damages.

Putting up plasterboard is way quicker than wet plastering and also significantly reduces the drying time that can slow down your renovation plans. With a plasterboard, you can delve straight into the decorating stage and achieve a smooth finish. Below are the steps required to put up a plasterboard.

• The first step is cutting the plasterboard to shape which be one of the most challenging parts of the process. This is because you’ll need to fit the board around things such as plug sockets and window sills. As a result, this involves cutting complex shapes rather than just a simple straight line. To get this done, simply mark out the cut required with the use of a tape measure, combination square and spirit level for a better precision. Once done, you can then use a plasterboard pad saw to cut along the marked spots.

• After you made the required cuts, the next step is putting up the plasterboard. And depending on where the boards are going to be put, this could be a very challenging task. If you’re going to put the boards on the ceiling or somewhere very high up, you’d probably need an extra pair of hands for help. To get this done, use the appropriate screws to secure the boards in place if you’re installing them directly on studs. However, if you’d be fixing them onto bricks or blocks, a drywall adhesive is your best bet.

Asides the questions relating to planning permission of a loft conversion as well as the total cost of completing a loft conversion project, this is perhaps the most common question on the loft conversion subject matter. Before making an investment decision, many homeowners will want to know just how disruptive a loft conversion is. Well, we’ve all heard the several horror stories when loft conversion builder with dirty boots tramples all over the fresh and just-acquired shag pile or the noise of the construction loud enough to annoy neighbours from four blocks away or an obvious shortage of teabags, sugar and lots more. Good news is, the disruption of loft conversion is not as bad as people make out. Let’s have a look at how it works!

Just like all other major building projects, a loft conversion is disruptive to your property. However, no two loft conversions are the same, therefore some are certain to be more drastic and invasive than others. In the long run, the project is worth the stress and inconveniences caused and in most cases, it’s usually a very good investment.

Normally, an average loft conversion is expected to last for about 9 to 12 weeks (depending on the complexity of the loft conversion project some might take longer). Some of the factors that affects the duration of a project includes the type of the loft, the design of the loft as well as the style of the property.

Generally, a loft conversion is a lot less disruptive than say completely moving a home. It all has to do with how you’re able to deal with it as a person. And besides, the effect it’s going to have to a large extent depends on the company you hire. A good company will always look to ensure to keep disruptions to a minimal when carrying out the loft conversion project.

Presenting with its unique sets of components, the price for every house renovation project varies considerably. Though giving a proper price for the house renovation is not possible, you can generally expect to pay anything between £40,000 and £75,000 for renovating a three-bedroom house.

You must list out all the changes needed since renovation comes with several potential costs. This makes it easier for you to calculate the renovation costs and start planning your budget accordingly.

Let us take a look at some of the crucial factors that affect the cost of renovating a house

• Property size

• Property’s condition and age

• Complexity oof the job

• Structural work

• Building extension work

• The quality of materials, fixtures and finishing

• Decoration

• Location

When it comes to renovating a three-bedroom house, the average cost is around £ 57,000. A new gas supply will cost you around £1,500, depending on the route of the supply. There may other additional costs involved if you are looking to do any work to extend the gas supply line.

The cost of rewiring a house is in the region of £5,750. That price will also be dependent on the complexity of the electrical systems in your house and the size. If you are looking at installing a new set of windows, it can cost you up to £6,000, with the average cost being about £4,250. Replastering walls will add another £2500 to the total budget. A new kitchen will set you back around £7,000, on average including the cost of design, materials and installation. Most renovations will need a new bathroom. Installing a new bathroom will cost you around £4,250.

Cutting a plasterboard is a relatively simple process requiring only some basic tools. Unfortunately, the lack of knowledge serves as big deterrent for many people who wishes to put it to good use. Plasterboard can actually be sawn using an ordinary timber saw that’s fine-toothed to get a cleaner edge. However, the basic tools you may also need includes a sharp knife (Stanley Knife), pencil, a fine sandpaper, a straight edge and measurement tape as well as a wall board saw. Let’s have a look at the cutting process!

• Firstly, you need to put the plasterboard sheet flat on a firm surface.

• Use the tape measurement to measure the cut you wish to make.

• With the help of a pencil, simply mark out the part you wish to cut on the plasterboard’s front side.

• Once marked, place a spirited level over the marked spot on the plasterboard sheet you want to cut.

• Cut a shallow mark into the plasterboard sheet using the Stanley Knife to cut along the edge.

• The cut should be slow and gradual to ensure you do not wander off the edge of the marked area.

• Once the shallow cut has been made, turn the plasterboard sheet on its edge and deliver a quick and sharp push towards the plasterboard’s back and on one side of the cut.

• Place the plasterboard sheet backing against a flat surface ensuring the line of the cut is over an edge. Once done, give a quick and sharp push towards the back of the plasterboard sheet and on the part of the board is reaches beyond the edge.

• Using a fine sandpaper, remove all forms of paper burrs.

The process of cutting plasterboard requires a lot of practice. If you lack the training and experience, the cutting process is best left to a proficient professional who can guarantee the best results the first time and save you some additional costs due to potential damages.

For 2 metre solid fences it’s recommended to use concrete posts to support each panel. For smaller 1 metre fences or for picket fences with gaps between each timber piece you can use timber posts. A fencing contractor will be able to advise you on the best materials from the length and requirements of a new fence.

Driveway surfacing materials like concrete, asphalt and clay brick usually crack because they’ve been exposed to extreme temperatures or put under high pressure. It’s important to repair driveway cracks before they get worse and cause damage to vehicles and perhaps others to trip on raised cracks.