Find a Builder you can trust in Ryton.

Render serves two basic functions. One is it’s protective qualities as render acts as waterproof for the wall which enables them breathe by allowing water vapour move from the inside to the outside of the structure while also working to prevent water or rain from finding its way inside the structure. While the second function is the decorative qualities as render is able to provide the structure with a fine finish and colour to make the building a lot more appealing and correcting faults in line and level in the masonry.

If you wish to apply render on your external wall, you’d probably be wondering just how thick the render should be to perfectly serve both of functions. In this article, we’re going to take a look at just that!

For a render thickness, the British Standard Wind Driven Rain Index has come up with 4 ratings which include Sheltered, Moderate, Severe as well as Very Severe. An area with Very Severe rating include South West England. This rating implies that the thickness of the render in this area should be increased to at least 20mm for a direct one coat render applications as well as 5 to 6 external wall insulation base coat applications. And if you happen to reside within one mile of the coast, it’s strongly recommended you incorporate an extra repellent protection like Paraguard AG from Parex.

In general, render that’s prepared on site with cement and sand should be have a minimum of 20mm to 25mm thickness. Although, it should be noted that the quality of the render is based on quality of the sand incorporated, the design mix as well as being largely dependent on how good the mixing technique from the applicator is. The most common reasons why traditional renders fails is due to both poor mixing ratios and low quality materials used.

There are two main types of cladding. The first is material cladding, which refers to layers of a material that are attached to the external walls. The material used could be timber, PVC, stone, or other materials. The second type of cladding is rendering, where a coat of plaster is applied to the wall.

In general, you won’t need planning permission to install soundproofing. If you are installing soundproofing against a shared wall, you will usually need to follow the rules and restrictions set out in the Party Wall Act. In listed buildings and conservation areas, there may be extra restrictions on soundproofing.

It’s often said that a garage conversion can take anywhere between 1 week to 1 month, depending on the size and scope. But many standard conversions without any plumbing can take as little as 5 days. Your contractor will be able to tell you exactly how long your garage conversion will take.

The short and simple answer to this question is yes, loft insulation does cause condensation. Over the years, problems with condensation in loft spaces have become increasingly common. While this may not be harmful in anyway, when the condensation becomes excessive it can lead to more serious issues taking root in your loft like wet rot, dry rot as well as black spot mould. Generally, the best thing to do if you’re concerned about the condensation in your loft space and that it may rapidly become a bigger problem is to get in touch with a damp specialist as soon as possible.

Even though insulating your loft space comes with a wide array of benefits like making the top floor rooms warmer, it’s however comes at the cost of making your loft or room space cooler. Condensation in lofts take place primarily due to the humid air making its way through insulation or other gaps into the loft space and touching a cooler surface which in turn results in beads of moisture on the timbers, lintels as well as the underside of the roof. This is why its always a great idea make use of thermal insulation with a vapour barrier that’s installed on the warmer side of the insulating material.

Condensation in loft is caused by excess moisture in the air and lack of adequate air ventilation. Here are some top reasons that gives rise to this in the loft:

• Extra insulation has been installed in the loft leading to a restriction on the natural air circulation in the property.
• When the storage boxes or other items that has been stockpiled in the loft blocks the roof vents.
• The release of steam and moist air into the loft space by hot water tanks.

External wall insulation works to keep your home cosy and comfy while also helping to cut the energy bills. However with the great benefits also comes great costs, so it’s actually a logical decision to know whether there are grants out there which you’re eligible for to help you handle the cost of the external wall insulation.

There are grants available for external wall insulation, but rarely will you find one that covers the full installation cost. With the help of the government’s Energy Company Obligation (ECO) scheme, a couple of energy companies assist in making your home more energy efficient by offering grants or free insulation. In certain cases whereby you receive particular state benefits, you may as well qualify for a higher grant that’ll cover more of the insulation cost.

However, if your energy supplier doesn’t offer any grant, you need not worry as you can save as much on energy bill after installation. Here’s what insulation can help you save per year on energy bills:

• Floor insulation can help you save within a range of £30 to £75 each year.

• Cavity wall insulation can help you save about £85 to £280 a year.

• Loft Insulation (270mm) can help you save about £135 to £250 a year.

Generally, the amount you’ll be able to save on your energy bills depends mainly on the type and size of your property, as well as how energy efficient it already is without the insulation. In the long run, your external wall insulation will more than give you back your investment on the valuable project through your savings on energy bills. In other words, whether or not you’re eligible for a grant should never stop you from installing an external wall insulation.

How Much Does A Loft Room Cost

In the event whereby you happen to run out of space in your home and extending sideways or moving out isn’t even a considerable option, the next best solution is to look upwards - the loft. The loft can be converted into a room that can used to satisfy varying purposes, be it a storage room, bedroom, home office, spare bathroom and more. There are a number of loft conversion styles you can go for including a room in loft conversion, dormer style conversion, mansard conversion, or a hip-to-gable conversion. Regardless of your choice, each of the types will not only give you new rooms to enjoy but also add value to your home. However, before getting started, it’s crucial to have an idea of the loft conversion cost to help you prepare a budget and begin planning. Here, you’ll discover the most likely loft room cost for each conversion style you opt for.

• Room In Loft Conversion

This is only suitable for some specific home, but it’s however the most affordable option of the lots. This loft conversion style will cost within the range of £15,000 to £20,000 (prices can be higher in regions where tradesmen are higher in demand such as London and the south east).

• Dormer Loft Conversion

These are relatively simple and straightforward to include in your home. The cost ranges between £31,000 to £58,000 depending on the conversion’s size and other factors.

• Hip To Gable Loft Conversion

This style of loft conversion is more complex than the aforementioned ones, hence they’re usually more costly to complete. The price ranges between £42,000 to £65,000.

• Mansard Loft Conversion

This style of loft conversion is the most complex of the lot and includes a complete overhaul of your loft. The price ranges between £45,000 to £70,000.

• Bungalow Loft Conversion

Any of the main styles above can be done to a bungalow if the planning requirements are fully complied with and if the property is suitable. The price ranges between £30,000 to £70,000.

Rendering is an external wall’s plastered finish which provides a smooth finish while also protecting the brickwork from the elements like rain, snow and the likes. The traditional rendering is normally applied in two or three coats which enables it to be more resistant to surface cracks. In modern times, the finishes are largely different from the grey pebble dash of post war housing. Today, we now have a plethora of specialist products to pick from such as through-coloured silicone renders as well as one coat renders. The types of renders include the following:

✓ Cement renders. These are the common option that are usually mixed on site and used in a number of applications, then painted when dried. There’s a need to paint this type of render regularly to keep them looking great.

✓ Polymer renders. These are pre mixed and mostly pre coloured (usually with through colouring).

✓ Through-coloured products. These rendered do not need to be painted as the pigment is already added in the manufacturing process to colour the whole render.

✓ Lime renders. These are superior to cement as they’re less likely to trap moisture in the brickwork and also more good looking. However, they’re generally more costly and more difficult to apply.

Overall, rendering on a house provides several benefits. Not only is it able to protect your brickwork against the elements like the rain and wind, but it can also make the building more efficient. Being fully aware that about 30 percent of the energy used in heating a home is lost via the external walls, making use of a product such as acrylic insulated render is a smart approach to improve your home’s energy efficiency without affecting your interior living space.