Find a Builder you can trust in Llansanffraid.

Are you considering converting your garage into a more usable space in your home? If yes, then you’d probably want to know if you’ll require building regs before converting the garage. The answer to this question is yes. Although you may not require planning approval to convert your garage into a more usable space, but you’d usually need approval under the Building Regulations.

When re-structuring your garage into a habitable space, the following should be taken into consideration: structural alterations, ventilation, moisture proofing, insulation, fireproofing, escape routes as well as the submission of a building building notice or full plan application to the local council in order to inform them about the planned project.

• Walls

You’ll require an approval if you plan to infill the garage door with a window and a new wall. This is because the garage may have been built of a shallow slab which implies that a new foundation would be needed for the new wall construction.

• Floor

Even though there’s a high possibility that the garage floor is strong enough for domestic use since its designed to withstand the weight of vehicles, you may however need to upgrade to make sure it suitable for both thermal insulation and damp proofing. In addition, there may also be the need to to alter the floor level in such a way that it matches that of the remaining parts of the house.

• Ventilation

According to the Building Regulations requirements, there’s a need for adequate ventilation for each individual rooms which includes garage conversions for general health purposes. What’s going to determine the ventilation level that’ll be required is the frequency at which the room is used. Ventilation can be provided through purge or simply opening the window or via trickle ventilation.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

A barn conversion is where an agricultural building is altered to serve a different purpose. Lots of barns conversion projects involve converting an old barn into one or more homes. However, barns can also be converted into other types of commercial building, like offices.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

Well, just like many other team work, a bricklayer is only as good as his supporting cast. And a hard-working labourer should be able to keep three bricklayer gangs happy. But even when he gets to serve just one bricklayer, the site conditions and nature of the wall can also play a huge role in determining the number of bricks that can be laid within 24 hours.

With the best possible site condition, hard-working labourer and best scenario with no pillars, no face brick, long straight wall and no wall ties, a well trained bricklayer should be able to lay within a range of 800 to 1100 bricks all day long. However, you rarely get walls like this as there is always going to be some corner or curve somewhere which usually takes some time to get right. Furthermore, once the bricklayer has laid up to 5 feet, there’ll be a need to get some lift. From that point onwards, the job understandably gets slower and tougher - meaning there’ll most definitely be a face brick.

In addition, there are multiple other factors that can affect the number of bricks that can be laid in a day. Sometimes its the complex designs or weather that’ll determine the daily rate.

With the aforementioned factors and more realistically, on a good day and great site, an expert bricklayer should be able to lay about 500 to 800 bricks in a day. This is generally a very good target, but of course you never can tell with the reasons above and other factors that are simply beyond the control of the bricklayer. If you have a project and want it completed as soon as possible, you can pay the bricklayers based on the number of bricks laid to increase their efficiency.

If you want to install an external wall, it is only wise to consider whether or not a planning permission is required in order to avoid a hefty fine. In a great kudos to the government and a welcome relief to home and property owners, the installation of external wall insulation is seen as an “improvement to the house and not an “extension or an “enlargement. Ultimately, this implies that external wall insulation fitting is to be done under permitted development and a planning application may not be required. However, like many other regulations, there are also exceptions to this rule and the main one is if the activity changes the appearance of your property. Properties such as a listed building having tighter regulations may pose some issues. As a result, we’d advise you to consult your local authority to ensure that there’s no fast rule to this topic before commencement of the external wall insulation project.

At the moment, according to the Government Building Regulations, the surface of the entire wall is to be improved to existing standards if the area to be insulated exceeds 25 percent of the wall. In normal situations this is usually the typical case, however to prevent avoidable fines and other possible punishments, it is always best to reach to your local authority and check out the rules guiding external wall insulation in your constituency. Furthermore, since external wall insulation is not a task that’s recommended to be done by yourself, you can also ask the professional external wall insulation fitting company for the applying rules before proceeding. As a good professional, the company should have a better knowledge of the rules and regulation guiding its activities.

In a nutshell, a mortgage loan is for the acquisition of an asset, so lenders won’t tend to give you anything else in a mortgage that is going to cover your home renovation costs. When you are applying for your mortgage, your provider will examine the price of your new household. For example, if you’re planning to buy a property for £200,000, but you need another £50,000 to help improve it, you’ll find that your lender might turn you down.

Essentially, with any mortgage loans that you take out on your possessions, the bank or creditor theoretically owns your home till you’ve entirely paid off your loan, which is why it is very unlikely that you will get extra funds from them. There are some mortgage providers who will be willing to add on some building costs, but it is entirely up to you whether to choose it or not.

With most mortgages, banks and other lenders will usually give you a maximum of 95% of what you purchased your property for. That means, that even if you contemplate the household has the probability to be valued at so much more, you’ll have to find an alternative way of paying for the developments you have in attention. So, if the accumulation of extra funds on to your mortgage loan is out of the question, you’ll need to find additional ways of paying for the home developments.

It is well and good if you have the cash saved up, or else, you can explore other payment options which your bank or lender may be able to help you with. There are several methods by which you can collect the cost to pay for the improvements, from personal loans to credit cards or even overdrafts, there are tons of ways to lending money. Keep in mind these are all forms of debt so keep an eye out for the interest rates when you are repaying.

Damp issues on a property are usually generated by a lot of factors such as a poor or broken guttering, condensation and lots more. The question arising here is what is the possibility of External Wall Insulation (EWI) preventing condensation? Not only is EWI a reliable way to reduce condensation-caused damp, but it’s also one of the major reasons property owners in solid wall homes consider thermally rendering or cladding their external walls.

Condensation arises as a result of warm moist internal air hitting a cold surface such as the steaming up of both windows and mirror when having a shower. What happens here is the condensation of the water vapour in the air from a gas to liquid in the process of touching the cold surface - one whose temperature is significantly reduced to reach the dew point. At the dew point, condensation is very rampant, and to tackle this issue you’ll have to heighten the wall temperature in order to convert the moisture to vapour and permit it to pass through the wall. And that’s exactly the job of an external wall insulation!

To get started you must ensure that the walls are clean and dry prior to fitting the external wall insulation. The month of May through to September when the weather tends to be dry and more stable are usually the best period to carry out the project. The external wall insulation will function just like a cosy blanket around the building. Ultimately, changing the feel and temperature of the inside of your home. As a result, the previously cold walls will no longer be cold which goes a long way to mitigate the effects of condensation. Furthermore, when an EWI is installed, the rooms of your home will automatically trap more thermal mass as the heat is saved in the walls’ fabric and released back when the temperature drops.