Find a Builder you can trust in Pentre.

External cladding will have an impact on a damp problem. However, it’s important that cladding is the last part of a damp treatment, as installing cladding over a damp wall will make the problem worse. Do not cut corners or try to remedy a problem with the cheapest solution, a damp proof course may need to be put in place before cladding.

How To Lay Loft Boards

Do you need more storage space in your home or property? If you live in a tiny space especially where extensions can’t be made sideways, why not look to the topmost area of your home and consider boarding out your loft to make it usable?

Boarding your loft can make for a fairly easy DIY project but like every other home improvement tasks, it requires some specific skill sets as well as knowledge for a successful construction. Therefore, we’d recommend you hire the services of a reliable professional in order to guarantee the best possible outcome, especially if you lack proper training or experience that’ll help you avoid some costly mistakes. Here, we’ll give you a good insight into the loft board laying procedures.

• Get The Right Tools & Equipment

The materials and supplies you’ll need to lay loft boards include loft boards, screws, tape measure and pencil, drill, hammer, saw, protective gear such as gloves and dust mask.

• Work Out The Area

Measure up the area you need the boards to cover. The standard loft features two different sizes (both are 18mm thick) which include 2400mm x 600mm and 1220mm x 320mm. You should ensure that the board you opt for fits through the loft hatch perfectly.

• Start Laying

Once you’re done working out the area, the next step is to put on your protective gear and start putting the boards in place. You should lay the boards in a staggered pattern so as to give a better strength. While doing this, watch out for any wire running through your loft so they don’t get trapped, you should also cut the boards for easy access to the light fittings’ top.

• Make It Permanent

Upon the successful placement of the boards in a way that offer a safe area to store things and stand on, you’ll have to screw them in place. Start by drilling 2 or 5 holes along the edge of individual boards in such a way that lines up with the centre of the joist below. Once done, then you can fix them in place with screws.

Yes. Most extensions will add substantial value to your home, and you may find that the extension adds more value than it cost. However, it’s important to be sure that the home remains balanced. Extending your garage and leaving your property with no parking spaces, for example, may impact your ability to sell.

Have you decided to improve your property instead of moving? The common problem most homeowners face after deciding to embark on a home extension project is not knowing where to start. In this article we’ll walk you through everything you need to consider and put in place before commencement of your home extension project.

• Is the extension worth it?

Before breaking the bank, you must be sure that the project will add good value to your home. In terms of “value, this is not only limited to the financial gain after disposal of the property, but also several other juicy benefits to be derived from extending your home like an extra living space for the household to spread out and more.

• Do you need a planning permission?

Check with your local authority to determine whether or not you’ll require to submit an application. You can also consult a building expert like an architect for advice.

• What are the building regulation?

Even though planning permission can be dodged, you can not avoid building regulations. These regulations are the set national minimum standards for construction and design which you must comply with to ensure the safety of the individuals in and around it.

• Who will design the extension?

You have to decided whether you’ll hire a professional architect to design the extension or not.

• Who will manage the building work?

If your home extension project is designed and built by a professional company, they’ll be responsible for the management. However, if you decide to use an architect or designed it yourself, you’ll have to hire a main contractor to manage the build.

• How to set the budget?

There are so many factors that can affect the cost of an extension, so it’s better to get the costs from your builder before proceeding.

• Do I need yo inform my home insurance firm?

Absolutely! This is very important as the new extension may affect the rebuilding cost of your property which could have an impact on the policy premium.

• Do I need to inform my neighbours?

It’s very important to discuss your plan with your neighbours before applying for a planning permission and communicate about the concerns they might have.

Sand is a very important element in bricklaying as far as a mortar mix is concerned. Generally, the quality of the sand is the major factor determining the quality of a plaster mix or mortar mix. It’s recommended that the sand should have enough ‘fines’ (- 75 micron material) to get a good plastic mix with a water content that’s less than 350 litres/m3. Generally, a mortar mix or plaster mix is made within the range of one bag of cement to 200 to 300 litres of damp sand.

Apart from experience the next best indicator of the quality of sand is a field test. In other words, if you do not have the required training or experience in bricklaying, the best bet to determine the amount of sand for a good quality mix is by carrying out a field test. Let’s have a look!

• Get about 50kg of sand and air dry it.

• Scoop 25kg of the sand, 5 kg of cement as well as litres of water ( with 1 litre and 1.5 litres of the water in different containers).

• Mix the cement and sand to form a smooth, uniform and consistent colour.

• One after the other, mix the the sand - cement mixture in the three quantities of water. Do this until you’re able to achieve a mix that’s workable enough to use as plaster.

With that done, you should take note that if 5 litres of water is sufficient then the quality and quantity of the sand is perfect. If you’d require 6 litres of water to get a mix workable as a plaster, then both the quality and quantity of the sand is average. However, if you’d need 7 litres of water to get a mix workable as a plaster, then the quality of the sand is poor. Any requirement of water above 7 litres implies a very poor quality of sand.

If you’re considering rendering your house or property, then you’d most likely want to know whether or not applying for a planning permission will be needed. In several cases, planning permission will not be required for the maintenance, repair as well as replacement of the existing render on your building. These activities are covered by what’s called “Permitted Development Rights, which allows you to carry out some activities without having to apply for a planning permission but always subject to following some strict guidelines. For rendering, as long as the material (render) possesses an identical appearance to those existing on the house as well as same colour, then you will not require a planning permission. However, there are a number of projects that have been highlighted in which a planning permission would be required. These includes the following:

✓ Re-rendering in a colour that different from the original one used on the house or building.

✓ Rendering over brickwork which was not originally covered.

✓ Rendering over pebbledash

✓ Removing pebbledash and replacing it with render.

Another exception to the Permitted Development rights are for houses in conservation areas, national parks or areas of outstanding national beauty.

Although, you wouldn’t normally require to submit a planning application for approval before you apply render, but in truth it’s actually a bit of a grey area which isn’t totally clear and doesn’t allow for much freedom or creativity. And due to this fact, homeowners who wants an absolute peace of mind may opt to apply for planning permission just in case. It’s also worth noting that whether or not a planning permission is required, a huge rendering work will need to comply with building regulations which includes the need to insulate walls on the inside or outside as part of the work on several older properties .

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the ours so that you can find quality tradespeople and see genuine reviews from previous customers. Not all online review sites can be trusted to display real reviews.

Yes, bricklayers can work during the cold months, but it all depends on the type of work involved. For instance, residential housing maintenance works such as tuck pointing deficient mortar joints on exterior walls and columns as well as rebuilding of chimneys are best tackled during summer or simply put, the warmer months of the year. This is is mainly because the best results for these activities are achieved in the warmer months and several bricklayers will agree to this fact.

Mixing of mortar using anti-freeze technique to counter-act the effects of a cold weather can lead to white marks trailing down the brick when warmer temperatures comes knocking. As a result, even mortar mixing should be done at temperatures exceeding zero degree farenheit which will hold no serious consequences if the temperature should change to a little bit below the norms. During the winter, a good technique that can be incorporated to when mixing mortar would be to mix them in smaller quantities in a warmer environment. These small quantities will immediately be fed by the labourers to the bricklayers and in such circumstances, the mixed mortars will not be subjected to a freezing temperature for too long.

Generally, it would be very unwise to consider any bricklaying work to be done whenever the temperature jumps to a certain level which would be considered to be very inconvenient to work in. Interior works like remodelling of fireplaces can be tackled so long there is a warm space to mix the mortars while also keeping the materials at an indoor temperature. Bricklaying works that have, however, been completed during the colder months should be subjected to a very close inspection as well as looking for potential damage that can be caused to existing works as a result of the harsh weather.