Find a Builder you can trust in Wandsworth.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

Over the years, garden rooms have gradually become a popular choice amongst homeowners as a cost effective way of expanding living space within a home or property. A garden room is basically a living space and a type of pavilion building made from wood that’s well insulated, double glazed as well as electrically wired. It’s however a building which is subsidiary to the main one, built with the purpose of creating an extra functional space within the property. These garden outbuildings are very functional and can be used as a garden studio, office, salon and much more. They can also be incorporated for recreational purposes for evening relaxations, family and friends get-together, lounge or even spa. Other possible uses of a garden room include gyms, pool houses, playrooms, dens, home cinemas and game rooms.

Garden rooms are functional living spaces that are usable throughout the year. And with the rate at which their popularity is growing, you’ll find some companies offering cheap and low quality alternatives featuring shed like construction and felt roof. Garden rooms, on the other hand, are a valuable investment with superior designs and top notch build. They’re constructed in a very similar way to houses with timber frames. Furthermore, they are fully insulated and can also include the normal building solutions such as heating and running water, electricity and many more depending on the requirements of the home or property owner. With the durability of garden rooms being a major objective, they’re typically clad in natural solid timber like Cedar, Larch or Acacia. Materials such as EPDM rubber or cedar shingles are normally used for the roof covering. What’s more? They usually have large expanses of glazing and glazed doors fitted.

Do you know about 25 percent of heat that escapes from an uninsulated house are lost through the roof? Fortunately, roof insulation is something that can done by all DIYers irrespective of their experience levels. However, if you happen to lack the confidence necessary to pull off this, then it’s strongly recommended that you hire the services of a professional who can guarantee the best results and also save you time and money that could arise from potential cost mistakes. Let’s take a look!

• Clear out all clutter. This involves taking out all the rubbish and clutter from the loft. In order to work effectively, you’ll need a totally clear and empty loft space.
• Ensure that there’s sufficient insulation. The importance of a good ventilation cannot be overstated. Poor ventilation will result in forming of condensation and this condensation can make the roof timbers rot and compromise the structural integrity of the entire roof. If there are no roof windows which is the easiest way to provide a loft ventilation, the next best option would be to follow the loft floor along to the point where the roof comes down to meet it. There should be a gap at this point, also referred to as the eaves, between the outside wall and the underside of the roof.
• Measure your loft area. Take a measurement of the loft space in order to calculate the amount of insulation as well as the type you need. If you’re not sure, always get more that it’s required as skimming on the amount you use will only back fire in form of increased energy costs
• Check for water pipes.

To get started, simply make sure all cracks and gaps in the ceiling are filled using a standard filler or decorator caulk. Once done, clean the gaps in the joists and even to the point of hovering all the dust up. Finally,check for the hazards that can cause you problems before laying the loft insulation.

If you’re currently experiencing some structural issues with your building or property and you’ve heard a thing or two about the several benefits associated with getting underpinning done, you may be wondering if underpinning might just be the answer to your worries. Well, one thing you should when it comes to underpinning is the fact that, while there are some structural issues that may actually warrant an underpinning job, there are also some situations that can not be fixed by underpinning. In this post, we’re going to consider the events whereby underpinning of your house will be required. Let’s take a look!

First and foremost, you should know that underpinning isn’t required for issues related to slab heave. Footing movements which are likely to reverse normally occur when the content of the soil moisture changes unevenly which gives rise to slab heave. This movement results for a reversible effect.

Generally, underpinning is done to remedy problems related with the movement of the footings of a building or property, but as stated above – not all movements require underpinning. So, when is underpinning required? More often than not, a situation that’s resolved by underpinning is the event whereby the footings of a building or structure drops or subside as a result of some reasons that are irreversible. For example, footing movements caused by a footing set on a soft or loose soil which may be irreversible.

In the event whereby the footings of your house haven’t been installed as deep as required during the initial construction, then you will need to have your building underpinned to make it more stable. If you’re also looking to increase the load on your foundation like adding another storey, you may also need to have your house underpinned to support the extra weight added.

Cement is a crucial element in bricklaying that’s widely used in both construction as well as finishing works. Generally, they’re used to aerate concrete blocks, connect bricks, prepare plaster, floor levelling as well as the making of precast products. The major reason cement is one of the most common construction materials as its incredible ability to hold structure together. To get a cement plaster, you’d simply have to mix cement with both water and sand. However, when you mix cement with lime, sand and water, you’ll get a mortar.

For cements mortars to be used inside joints, you’ll have to include 1 part cement at the minimum to not more than 2 parts sand by weight which should be dry mixed and moistened with enough water to allow for troweling and packing without falling apart. Generally, the cement sand ratio in a mortar is in between 1:2 to 1:6. The cement and sand mix ratio is largely based on the importance of the project.

Cement provides a plethora of uses in bricklaying and these includes:

• Preparation of cement concrete

• Preparation of cement mortar

• Building fireproof and thermal proof structures

• Building chemical proof structures

• Serving as a grout material

• Building hydrographic and frost resistant structures

• Manufacturing precast members

• Constructing aesthetic concrete

• Constructing cement concrete roads

There are several types of cements with each having its specific purpose. For instance, the type of cement more suited to building a fire proof structure is a high alumnia cement and to build a hydrographic structure, cements like expanding cement, hydrophobic cement, pozzolana cement and quick setting cement are the best bet. Acid resistant cements are more useful in building chemical proof structures, portland cements are best suited to making grout materials, while coloured cements are preferable to building aesthetic structures.

There is a variety of methods available to ensure that your paving drains properly, for example draining into a lawn or soakaway. Correct drainage of paving is a requirement for planning permission. See our guide on planning permission for paving for more information.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

In the event whereby you’ve got big refurbishment ideas for your house but a small budget, then you know it’s time to be a bit more creative and apply some cheap and simple tricks. The best possible way to go about this is to invest time in acquiring new skills rather than trying to save up more money to pay a pro to deliver the results you want. After all, the most significant cost when it comes to house refurbishments is usually the labour cost.

The key to making cheap tricks a lot effective in the refurbishment process is by undertaking small tasks that’ll make a huge impact. A great way to start would be by taking it one task at a time rather than rushing to complete all at once. This way, you’ll have enough time to perfect your skills before moving on to the next.

✓ Paint the interior walls. Although this is a simple task but it’ll save you a lot of money if done as a DIY project. To get started, you’d have to text colour options by painting samplex on the wall first. Once done, you can go for the one that adds warmth, dynamism as well as energy to the room.

✓ Fix up your furniture. This involves re-upholstering and refinishing any piece of furniture that appears tired or overly worn (you can leave out the ones that you do not really like or unnecessary items).

✓ Spruce up small but important items used on a daily basis. This includes spray-painting inexpensive picture frames, recovering lampshades with a vibrant paper or patterned fabric, adding throw pillows to armchairs and couches and the likes.

✓ Fix all small things that are broken. This includes activities like patching the nail holes in the wall, repairing the latch on the kitchen cabinet, fixing the gutter, putting a new handle on the door and lots more.