Find a Builder you can trust in Larkhall.

Insulating your loft roof comes with a wide range of benefits. Not only do you get to maintain a comfortable temperature in your house for longer, but you’ll also get to cut down on your heating bills. If you wish to insulate your loft roof, you’ve come to the right place! This process can be very tedious and time consuming especially if you don’t what you’re doing or lack the required confidence to pull it off. It’s advisable to hire the services of a reputable professional who can guarantee the best results for help and also save you some time and money that can come from potentially costly errors.

Before you start rolling out, you’d have to make sure that all cracks, gaps and holes in the ceiling are filled with either a standard filler or decorators caulk. You can also clean between between the gaps in the joists thoroughly. And finally, check for hazards that can cause you problems before getting stated.

• Remember to leave ventilation gaps as you start from the eaves. Then work towards the loft’s centre, starting from the point furthest from the hatch.
• Lay the first layer between the joists which should be 100 mm and then the subsequent layer should be 170 mm to make it up to the recommended 270 mm.
• Carry the electric cables above the insulation and work around visible light fittings.
• Cut the roll in the centre of the floor when rolling out from the eaves on both sides with the help of a craft knife. Ensure that there are no gaps between the insulation and the joists’ edges.
• Lag pipes as you go in order to prevent walking over the insulation to get back to them.
• Ensure that the loft is totally insulated
• Insulate the hatch.

Do I Need Planning Permission For A Loft Room?

The answer to this question is maybe. Generally, loft rooms are covered under “Permitted Development which means you won’t need to apply for a planning permission to build a loft room. This is like an advance planning permission provided by local authorities to allow some particular building works to be done such as loft conversions, rear extensions and more. When you’re covered by a “Permitted Development, you’re given the free range to oversee your home’s development without much interference from the regulations or the council. However, for permitted development to apply, there are some specific criteria that must be met. Therefore, if your loft room does not meet the following requirements given below, then you must complete a planning application before proceeding.

• In a terraced house, the converted loft space must not be more than 40 cubic metres.

• In a detached building or semi detached house, the converted loft space must not be more than 50 cubic metres.

• The existing roof slope at the front of the house must cover the extension made.

• The extension should not increase the height of the roof in any way.

• Verandas, balconies and any other structures of this nature must not be included in the extension’s plan.

• The side facing window openings should be at a minimum of 1.7 metres above the ground. The windows must be obscured as well.

• The roof extension should be set back as far as practically possible. It should be at a minimum of 20cm from the current eaves.

• The roof extension should not overhang the house’s roof or it’s wall.

• The materials to be incorporated must be the same or at least similar to what you already have on the house’s exterior.

Aside from the cold weather not being the most pleasant condition to work in, the winter weather can also cause a lot of problems for construction workers and even more so when you’re working with render. Poor weather conditions can generally cause a lot of harms on the final finish of a render. Below are some of the reasons why you should not consider rendering in a bad weather.

✓ Lime bloom. Render can be impacted by lime bloom as they are subjected to damp conditions and low temperatures while curing. This is due to the fact that cement are intolerant to slower drying conditions especially immediately affect its application.

✓ Top coats can be compromised. Coating are likely to get washed off before they’re even afforded the chance to set if drying conditions are low.

However, because its cold out there doesn’t necessarily imply that work must stop. It’s very possible to render during the winter months but to avoid potential pitfalls, we’ve got some tip that can be of great help. Let’s have a look!

✓ Check the weather forecast. Determine the drying and curing time and watch the forecast for the temperature dropping at night.

✓ Select the most suitable render. There are renders that are suitable for application in low temperatures to about 5℃ or even as low as 1℃. These types of render are fast setting which makes them perfect for the cold condition.

✓ Watch out for frost. Frost and render are enemies. Therefore, it won’t be wise to work with frosted materials, on frosted subtrates or apply below the recommended temperature that’s written on the product’s datasheet.

✓ Protect the finish. Make use of artificial enclosures around the scaffolding to battle adverse weather conditions.

How To Fit Plasterboard

If you’re planning to renovate your house, then here is a must-read guide! Fitting of plasterboard is a crucial step when it comes to renovation. If you’re bringing down an existing lath and plaster for an upgraded surface or adding a new wall, a plasterboard is required for your project to be a true success. If you’re a novice with no prior practice or experience, you can protect your investment by hiring the services of a professional plasterer to guarantee the best results, the first time. However, we’ve put together this guide to give you an insight on how the plasterboard fitting process is done.

To get started, you’ll need a power drill, hammer, plasterboard nails or screws, broad knife, utility knife, measurement tape, pencil, ladder as well as a joint tape.

Before proceeding, you need to identify the number of plasterboard sheets needed to commence the project by measuring the height and width of the wall as well as calculating the square footage. If you possess a stud timber wall, the steps below will get you the best results.

• Measure the walls and mark the plasterboard where you’ll make the cuts. Start with a full sheet and cut pieces down in such a way that would fit

• Score the front paper of the plasterboard with utility knife. Fold the sheet to get a clean cut through the board and make use of the knife to the remaining paper.

• Place the first sheet against the wall and use an offcut to prevent the plasterboard from touch the floor.

• Make the plasterboard rest snugly against the wall in position and screw it firmly on each stud. Once done, fasten it at all the sheets’ edges and in a line down the stud to make for a firm connection. Follow the same process for the remaining plasterboard sheet till the wall is fully covered.

Whether a basement is worth converting depends on your location and how much work it requires.

A basement conversion can be a great way to add space to your home, and can raise your property value. However, it can also be one of the most expensive ways to do this, so if there’s a possibility to extend your property, or convert a loft or garage, it’s worth considering this first.

You should also compare how much your basement conversion will cost with the amount it could raise your property value by. In some areas, a quality basement conversion could earn you money in the long run, but in others it’ll only cost you. If you’re planning on staying in your property for a long time this might not matter to you, but if it’s not your forever home then it’s an important thing to think about.

When Does A Loft Become A Habitable Room?

When a loft is being converted to functional space, there are a multiple options it can offer. It’s not uncommon that at the conversion of this space, many household may not have a specific plan on how it’s going to be used. However, they know later on an actual need might arise, perhaps as you start working from home, developing other hobbies that requires an extra space or the family grows.

The loft can easily be converted into a game room, study room, playroom or even a household’s “breathing space etc. However, when the family grows and you wish to make use of the space on the top of your home as an extra bedroom, there are many factors to consider. The fact is, just because there’s enough space to fit a bed, doesn’t make it habitable. For a loft to become habitable, it must be built specifically for the purpose of being a sleeping area and must also comply with the relevant building regulations. It’s as a result of this, many property sale particulars include “potential third bedroom, subject to regulations statement written on it as well as the boarded and insulated loft space’s dimensions.

Loft conversions building regulations are set in such a way to ensure that adequate attention is given to both safety and structural elements to build a new space that’s fit for undetermined household use. These regulations are established minimum requirements to guarantee the following:

• The new floor and ceiling’s structural integrity.

• The existing roof and party wall modification’s structural stability.

• Safety during fire incidents plus an escape route.

• An appropriate stairway access.

• The proposed changes’ structural suitability to the external environment in association with the local area as well as any unique factors specific to the property.

If you’re about to carry out a loft conversion project, you’d probably be wondering how long it’ll take to complete the task. Well, you’re not alone! This is one of the most common questions when it comes to loft conversion projects, however, providing a set timeframe for completion of such projects is impossible as all loft conversions vary. There are different factors that can determine the duration of your project. These factors include, the materials to be used, the type of the proposed loft conversion, the kind of staircase you’ll like to have installed, the number of windows included, the number of rooms to be added as well as a number of other influencing factors. As a result of these variables, the milestones and timings provided are only to be taken as guidelines. If you’d really like to have a set date, you can get in touch with a professional for help.

Generally, it’ll take up to 8 weeks to complete a loft conversion project.

✓ The first week activities will include putting up scaffolding, receiving the first materials for the build and creating an opening in the roof to gain access to the loft space.

✓ In the second week, the structure of the roof will be ammended and more support added.

✓ Third week, the floor joists will be fitted, building of the loft conversion will start, completion of the external roof works and commencement of plumbing and electric works.

✓ Fourth week, complete the building, construct the loft floor, fit the roof windows, insulation, ventilation and internal stud walls.

✓ Fifth week, apply plaster and plasterboard to the room walls, create a staircase opening and fit the new staircase.

✓ Sixth week, plaster the staircase area, complete plumbing and electrical works, hang the doors, fit skirting, handrails and bannisters and start decoration.

✓ Seventh week, complete the decoration and clean and wipe out all wastes.

✓ Eight week, complete all the remaining tasks.

Rendering of a house is one of those projects that can greatly improve the visual appeal of your home, enhance it’s energy efficiency, protect the brickwork from the elements and ultimately, add value to your home. Generally, the cost of rendering a house normally costs within the range of £25 to £70 per metre square, while the average cost house rendering costs stands at about £40 per square metre. Therefore, a 3 bedroom semi detached house will cost within the range of £4000 to about £5000.

The total cost of rendering a house is determined by a wide range of factors. These factors includes the following:

✓ Type of the rendering. There are three main types of rendering which includes sand and cement rendering, monocouche rendering as well as acrylic or silicone rendering. However, re-rendering applies to sand and cement sooner and it’ll also have to be painted every 3 to 6 years. Consequently, longer term cost can be higher when compared to the other types.

✓ Ease of access. Where your contractor will have to work around obstacles like shrubs or conservatory, this can make the cost a bit higher as it’ll take longer time to complete.

✓ Prep work. If the contractor needs to fill some cracks or perhaps an old mortar requires tuck pointing before rendering can be started, this will also affect the cost.

✓ Scaffolding. In the event whereby the job requires the use of scaffolding and you’ll have to hire one as a different cost, then the price will be higher.

✓ Your location. Due to the high standards of living and higher demands in areas like London or the Southeast, prices in these regions are usually higher than that of the other regions like Midlands and North.