Find a Builder you can trust in Achnasheen.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

How Much Plasterboard Do I Need?

Although many people especially contractors have a tough time estimating the number of drywall or plasterboard needed to complete a project, it’s a rather simple task if all factors are taken into consideration. If you’re able to follow the same procedures taken by professionals to count dry wall sheets, you’ll be in the right direction. Let’s have a look at the procedures to follow!

lTake Square Footage Measurement

• Measure the square footage of the area where the plasterboard will be fitted.

• Multiply the height by the width of each wall or ceiling area.

• Add all quantities to obtain a total square-foot amount.

lCalculate Drywall Sheets

• To calculate the number of drywall or plasterboard sheet is very simple once you’ve gotten the total square footage.

• To get started, simply divide the total square footage of area by 32 (that’s if you are using a 4 by 8 sheets) or you can also make use of 48 to make the division (only if you’re making use of the 4 by 12 sheets).

• The answer you get after the division will give you the full number of plasterboard sheets that’s required to complete the project.

We’d recommend you include an extra 10 to 15 percent of whatever you calculate to take care of the possible odd cuts and wastages. This implies that if your total area is 1600 square feet while incorporating 4 by 8 sheets, simply divide 1600 by 32 which equals 50 sheets, now take 10% of 50 which equals 5, then add back the 5 extra to the 50 sheets earlier calculated to get 55 sheets. If you wish to estimate the cost, simply multiply the number of sheets gotten by the price per sheet. Do not forget to include delivery charges and local taxes.

When your driveway is suffering from depression, it becomes unsafe for driving (a danger zone) and ugly - no homeowner wants that! Unfortunately, most driveways won’t hold flat for long as they tend to develop cracks and potholes pretty quickly. Here, we are going to take you through how to fill asphalt driveways’ depression so as to ensure the sinkholes in your driveway poses no threat to you or your loved ones, while also beautifying your property. The approach to be used depends on the intensity of the depression. If its only a few cracks and holes, this can easily be repaired with some equipment. But if otherwise is the case, then calling a reliable professional will be your best bet. In this article, we’ll show you how to repair dips in your asphalt driveway relatively quickly.

✓ Pick a date with warm and sunny weather. This is because if you work in a cold weather, chances are the materials will freeze and hence, unusable. So find a day when the temperature will over 50 degrees Fahrenheit and below 80 degrees Celsius and when there would be no rain. We’ll advise a day between May to October.

✓ Prepare the area. Remove all loose stones, soil, dirt as well as vegetation from the holes. Once done, you can then proceed to washing the area with a pressure washer or sweep with a broom.

✓ Apply a thin mixture of asphalt to the area. Use a flat stirring stick to coat the low driveway area with a thin mixture of asphalt.

✓ Tamp the asphalt repair mix. Purchase the right kind of asphalt to repair the driveway. Fine aggregate asphalt mixture is more suited to filling small holes, whereas the coarse aggregate is more suited to filling larger holes. Apply layers ( about 2 inches each time) of the asphalt repair mix to the sunken area and use a shovel to give it a smooth finish. Once done, simply make the area smooth and protect it with a piece of plywood. Do not walk or drive on the area for a couple of days.

Typically, loft conversions do not require planning permission except in certain situations. They’re usually covered under what’s known as Permitted Development. Certain building works like loft conversion, rear extension and conservatories are granted planning permission by local authorities. Permitted Development, however, gives you a free range to improve your home without having any issues from the councils or regulations. Before your planned loft conversion can be covered under Permitted Development, there are some certain criteria that must be met. This criteria includes the following:

✓ The extension must not go beyond the existing slope of the roof at the front of the house.

✓ The loft space converted must not go beyond 40 cubic metres in a terraced house.

✓ The roof’s height must not be increased by the extension.

✓ The loft space converted must not reach beyond 50 cubic metres in a detached or semi detached house.

✓ The plan for the extension mustn’t involve structures like balconies, verandas or anything other structures of this nature.

✓ The roof extension should be positioned as far back as possible or at least 20cm from the existing eaves.

✓ The side that faces the window openings should be at least 1.7m beyond the floor and the windows should also be obscured.

✓ The roof extension must not overhang the existing roof or wall of the house.

✓ The materials that are to be used must be similar or the same to the materials that has already been used on the house’s exterior.

However, you should bear in mind that there are some properties that are exempt from Permitted Development. Examples of these type of properties include conservation areas, Areas Of Outstanding Natural Beauty and World Heritage sites. Permitted Development does not also provide coverage for listed buildings.

Do I Need Planning Permission For A Loft Room?

The answer to this question is maybe. Generally, loft rooms are covered under “Permitted Development which means you won’t need to apply for a planning permission to build a loft room. This is like an advance planning permission provided by local authorities to allow some particular building works to be done such as loft conversions, rear extensions and more. When you’re covered by a “Permitted Development, you’re given the free range to oversee your home’s development without much interference from the regulations or the council. However, for permitted development to apply, there are some specific criteria that must be met. Therefore, if your loft room does not meet the following requirements given below, then you must complete a planning application before proceeding.

• In a terraced house, the converted loft space must not be more than 40 cubic metres.

• In a detached building or semi detached house, the converted loft space must not be more than 50 cubic metres.

• The existing roof slope at the front of the house must cover the extension made.

• The extension should not increase the height of the roof in any way.

• Verandas, balconies and any other structures of this nature must not be included in the extension’s plan.

• The side facing window openings should be at a minimum of 1.7 metres above the ground. The windows must be obscured as well.

• The roof extension should be set back as far as practically possible. It should be at a minimum of 20cm from the current eaves.

• The roof extension should not overhang the house’s roof or it’s wall.

• The materials to be incorporated must be the same or at least similar to what you already have on the house’s exterior.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the Federation of Master Builders. They have a search tool where you can find precise crafts in your area and look at their situations. All FMB members are assessed and individualistically examined and are checked to ensure that they have the correct insurances in place.

Fitted wardrobes are the best choice of wardrobe for most households and they’re a popular option for several homeowners for a good reason. Not only are they able to efficiently maximize your space and fit into any space no matter how awkward, but they can also be customized to fit your personal needs to feature custom lighting and many more. So if you’re planning to have one fitted but on a tight budget, you’d probably be wondering how you can install a fitted wardrobe in an alcove by yourself. This is a relatively easy task if you’re attentive to the details, however, if you’re not confident enough to pull this off, we’d advise that you get in touch with a professional who can guarantee the best results for help.

To construct a fitted wardrobe in an alcove, simply follow these steps:

✓ Take a measurement of the available space including the length, breadth and width.

✓ Sketch out what you want the wardrobe to look like while also staying within the measurements. Here, you’ll have to be particular about everything like the drawers, shelves etc.

✓ Build the frames upon which every other construction would be made.

✓ Attach the frames to the wall and floor. Make use of a hammer drill with a masonry bit to drill the holes if its a concrete floor.

✓ At this stage, you’ll have to start building your shelves in accordance to the number you’ll need.

✓ Based on the design in step 2 above, you’ll have to add the door at this stage. This is however optional as some homeowners prefer door-less wardrobes.

✓ The final step is to paint the the finished wardrobe to your taste with your choice of colour.

Damp issues on a property are usually generated by a lot of factors such as a poor or broken guttering, condensation and lots more. The question arising here is what is the possibility of External Wall Insulation (EWI) preventing condensation? Not only is EWI a reliable way to reduce condensation-caused damp, but it’s also one of the major reasons property owners in solid wall homes consider thermally rendering or cladding their external walls.

Condensation arises as a result of warm moist internal air hitting a cold surface such as the steaming up of both windows and mirror when having a shower. What happens here is the condensation of the water vapour in the air from a gas to liquid in the process of touching the cold surface - one whose temperature is significantly reduced to reach the dew point. At the dew point, condensation is very rampant, and to tackle this issue you’ll have to heighten the wall temperature in order to convert the moisture to vapour and permit it to pass through the wall. And that’s exactly the job of an external wall insulation!

To get started you must ensure that the walls are clean and dry prior to fitting the external wall insulation. The month of May through to September when the weather tends to be dry and more stable are usually the best period to carry out the project. The external wall insulation will function just like a cosy blanket around the building. Ultimately, changing the feel and temperature of the inside of your home. As a result, the previously cold walls will no longer be cold which goes a long way to mitigate the effects of condensation. Furthermore, when an EWI is installed, the rooms of your home will automatically trap more thermal mass as the heat is saved in the walls’ fabric and released back when the temperature drops.