Find a Builder you can trust in Potters Bar.

A dormer loft conversion is a type of loft conversion that’s built making use of a roof’s existing slope. In other words, it’s an existing roof’s extension which is constructed in such a way that allows for an additional floor as well as head room especially suitable for lofts lacking good amount of usable space. The dormer loft conversion is simply an addition to the existing roof looking much like a box-like build constructed onto a pitched roof as it creates walls that are vertical to the slope while also being 90 degrees to the floor.

This type of loft conversion is the most common amongst homeowners in the UK mainly because it represents a cost effective means through which you can add an additional usable space to your home or property. The structure extends for the slope of the existing roof and can easily be altered to suit various tastes or styles. Furthermore, if you’re looking for a type of loft conversion that aids to foster reduced disruption to work, then dormer loft conversion is also your best bet. This is due to the fact that the structure is built from a scaffolding made outside a home.

There are different types of dormer loft conversion and the one which will best suit your property will depend on the property type, be it detached, semi detached or terraced as well as the existing roof shape and size. The dormer loft conversion is a popular choice for a lot of homeowners for a variety of reasons. Let’s have a look!

✓ It’s very cost effective

✓ The dormer loft conversion does not require planning permission so far it complies with certain conditions and limitations

✓ It adds an extra headspace as well as floor space.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

It’s a fact that a garage conversion can go a long way to add a resale value to a home or property. Therefore, in the event whereby your home already has parking facilities in place you can put into consideration converting your garage into a habitable space which will add to the sales price of the house by adding an extra room or increasing the floor space. So exactly how much does a garage conversion add to your home’s resale value?

Garage conversions can be seen as a cost effective means of adding more space to your house. However, not only does it add space, but can also add up to 20 percent to the value of your home. It’s also a way of adding an extra living space to your home that’s not under strict planning complication unlike the alternatives. Generally, if your garage happens to be connected to your house, the cost of converting it to another room should between £10,000 to £20,000. As a home owner, converting your garage into an extra room can help increase the value of your home by up to £45,000. And if you’re to comply with the set rules under permitted development rights, you may not even require to submit a planning application.

In the event whereby your garage is detached from your house or perhaps you live in a flat ( or maisonette) or a listed building , you’ll need to apply to the local authority before commencing your project. It’s always wise to check if there aren’t any planning conditions attached to your home or property.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

Getting the opportunity to fit your very own bespoke wardrobe in your home is a really exciting prospect. However, when planning to install customizable fitted wardrobe, one factor that turns off most home and property owners is the belief that the bespoke solution is actually a very expensive one. But the fact, in reality, is that so far you’re prepared for any associated costs bespoke fitted wardrobes should not make you break the bank to get one done in your home. So if you’re planning to install this type of fitted wardrobe and wondering about the cost, you’ve come to the right place! In this article, we’ve put together the price range estimate as well as the potential extra costs to help you plan ahead and get your dream wardrobe without having to worry too much about unpleasant surprises along the way. Let’s take a look!

With some companies you’ll be provided with a fixed price which can’t be negotiated. While prices from other suppliers will usually start within the range of £1400 to about £1700 for the standard wood finish wardrobe, but this can also reach about £5000 or more for high end or premium finishes, without taking the cost of the added extras into consideration. Ultimately, this often implies having to pay out more money for interiors and additional features than you’re likely going to need. Below is a rough guide to the cost of fitted wardrobes from Spaceslide:

✓ The price for a 2, 3 or 4 door sliding wardrobe starts at £452.37.

✓ The price for a 3 door fitted wardrobe starts at £659.07

✓ The price for a 4 door fitted fitted wardrobe starts at £865.77.

Additional costs you’ll have to consider before getting started includes the cost of hiring installers as well as delivery and removal cost.

Render serves two basic functions. One is it’s protective qualities as render acts as waterproof for the wall which enables them breathe by allowing water vapour move from the inside to the outside of the structure while also working to prevent water or rain from finding its way inside the structure. While the second function is the decorative qualities as render is able to provide the structure with a fine finish and colour to make the building a lot more appealing and correcting faults in line and level in the masonry.

If you wish to apply render on your external wall, you’d probably be wondering just how thick the render should be to perfectly serve both of functions. In this article, we’re going to take a look at just that!

For a render thickness, the British Standard Wind Driven Rain Index has come up with 4 ratings which include Sheltered, Moderate, Severe as well as Very Severe. An area with Very Severe rating include South West England. This rating implies that the thickness of the render in this area should be increased to at least 20mm for a direct one coat render applications as well as 5 to 6 external wall insulation base coat applications. And if you happen to reside within one mile of the coast, it’s strongly recommended you incorporate an extra repellent protection like Paraguard AG from Parex.

In general, render that’s prepared on site with cement and sand should be have a minimum of 20mm to 25mm thickness. Although, it should be noted that the quality of the render is based on quality of the sand incorporated, the design mix as well as being largely dependent on how good the mixing technique from the applicator is. The most common reasons why traditional renders fails is due to both poor mixing ratios and low quality materials used.

With homeowners now a lot more unwilling to move or make any costly extensions due to the uncertainty that lies ahead in the property market of the UK, a garden building which represents a cheaper alternative seems to be the best option available. Not only is it one of the most affordable ways to add space to your home while staying within your budget, but it’s also one of the best ways to add immense value to your property as more and more potential home investors are now seeking properties with an outdoor garden room. They’re the perfect investment for those looking to expand their space without having to carry out huge extension projects which normally consumes both time and money.

Garden rooms are best built by professionals to guarantee the best results. However, if you feel confident enough to undertake the project, then this guide will give you an idea of the process.

✓ Build the foundation. Here you can build the foundation using concrete, but in cases whereby there are root systems closeby then you can make use of low impact screw piles.

✓ Start the construction process with timber frame, SIP panels as well as other modular components and materials

✓ Once you’re done with the construction process, the next course of action will be to develop and position the roof structure on to the top of the newly constructed garden room. Here, you can also decide to use sun pipe and solar heating or PV panels. You can also protect the construction from the elements by making use of cedar cladding.

✓ Doors installation. The best type of doors to use here are draught sealed doors which can also be treated hardwood or powder coated aluminium .

✓ Make the finishing touches here and there and make sure all connections are complete.