Find a Builder you can trust in Cemaes Bay.

How To Repair Sunken Concrete Driveway

If you have concrete driveway that’s cracked, uneven and mostly especially sunken, you’d know how distasteful it can be just viewing it on your property. A sunken concrete driveway is most likely caused by rainwater erosion removing the soil under it or a big root under it which as rotted over time. Another possible cause of the sunken concrete is an improperly prepared base which implies that the soil beneath wasn’t fully compact when the concrete was poured on it. Later on the soil beneath will eventually settle and shift below the concrete driveway which weakens the integrity of the entire driveway, making it more vulnerable to cracks, unevenness and sunken.

Two ways in which you can fix this problem includes either demolishing the whole driveway, re-compact the soil underneath and fill with new concrete or repair the entire driveway using an easy process called slabjacking. In this article, we’re going to look at the slabjacking repair process as it’s significantly less expensive than the demolishing approach and will also cause minimal disruption to your lifestyle.

Also referred to as mudjacking or concrete lifting, slabjacking is simply a process used to float your existing concrete back to its original position. If you are not a competent DIYer or lack confidence to pull this off, we’d recommend reach out to a professional for help. If otherwise, then you can practice the slabjacking process given below.

✓ Drill holes through the slab.

✓ Pump grout mixture through the holes. This mixture will spread out beneath he driveway and raise it up.

✓ Lastly, fill the holes and level the concrete driveway surface.in such a way to hide the signs of the repair made.

This is a process that works to efficiently get your driveway back in a top condition relatively quickly.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

If you’re currently experiencing some structural issues with your building or property and you’ve heard a thing or two about the several benefits associated with getting underpinning done, you may be wondering if underpinning might just be the answer to your worries. Well, one thing you should when it comes to underpinning is the fact that, while there are some structural issues that may actually warrant an underpinning job, there are also some situations that can not be fixed by underpinning. In this post, we’re going to consider the events whereby underpinning of your house will be required. Let’s take a look!

First and foremost, you should know that underpinning isn’t required for issues related to slab heave. Footing movements which are likely to reverse normally occur when the content of the soil moisture changes unevenly which gives rise to slab heave. This movement results for a reversible effect.

Generally, underpinning is done to remedy problems related with the movement of the footings of a building or property, but as stated above – not all movements require underpinning. So, when is underpinning required? More often than not, a situation that’s resolved by underpinning is the event whereby the footings of a building or structure drops or subside as a result of some reasons that are irreversible. For example, footing movements caused by a footing set on a soft or loose soil which may be irreversible.

In the event whereby the footings of your house haven’t been installed as deep as required during the initial construction, then you will need to have your building underpinned to make it more stable. If you’re also looking to increase the load on your foundation like adding another storey, you may also need to have your house underpinned to support the extra weight added.

Aside from the cold weather not being the most pleasant condition to work in, the winter weather can also cause a lot of problems for construction workers and even more so when you’re working with render. Poor weather conditions can generally cause a lot of harms on the final finish of a render. Below are some of the reasons why you should not consider rendering in a bad weather.

✓ Lime bloom. Render can be impacted by lime bloom as they are subjected to damp conditions and low temperatures while curing. This is due to the fact that cement are intolerant to slower drying conditions especially immediately affect its application.

✓ Top coats can be compromised. Coating are likely to get washed off before they’re even afforded the chance to set if drying conditions are low.

However, because its cold out there doesn’t necessarily imply that work must stop. It’s very possible to render during the winter months but to avoid potential pitfalls, we’ve got some tip that can be of great help. Let’s have a look!

✓ Check the weather forecast. Determine the drying and curing time and watch the forecast for the temperature dropping at night.

✓ Select the most suitable render. There are renders that are suitable for application in low temperatures to about 5℃ or even as low as 1℃. These types of render are fast setting which makes them perfect for the cold condition.

✓ Watch out for frost. Frost and render are enemies. Therefore, it won’t be wise to work with frosted materials, on frosted subtrates or apply below the recommended temperature that’s written on the product’s datasheet.

✓ Protect the finish. Make use of artificial enclosures around the scaffolding to battle adverse weather conditions.

How long it takes to install insulation will depend on the size of your property. In general, loft and cavity wall insulation can be installed in a day or two. External wall insulation will usually take longer to install. The rep or installer will be able to advise you when quoting for the job how long this will be.

The simple answer to this question is... they can be! Although there are many types of porch designs that are available in the market, the uPVC porch happens to be one of the most loved and cost effective. Most home and property owners prefer the installation of a uPVC porch for a number of reasons. These includes:

• Value for money

It’s no coincidence the uPVC is widely accepted across the building industry with a plethora of uses. Not only is it relatively inexpensive to manufacture, but even the recycled uPVC is now becoming more and more useful. UPVC’s main rivals are wood and aluminium, and both are way more expensive to incorporate for frame profiles. Therefore, making use of uPVC is going to make your initial costs relatively low.

• Life Span

Although the main rivals in both hardwood and aluminium can also boast a lengthy lifespan just as uPVC. However, considering the price that you can get a uPVC, the lifespan is just incredible as it can be measured in decades.

• Aesthetic Appeal

UPVC gives you a wide range of foil colours that’ll fit your home perfectly well while also enhancing it’s visual appeal. You can actually get a porch that looks exactly like it’s manufactured from timber frames. To achieve this, all you need to do would be to make use of a wood grain surface finish. This is also long lasting, strong and resistant to fade.

• Little Maintenance

This is a very common feature of uPVC that makes it even more advantageous when used in making a porch. Unlike timber or wood which swells due to absorption of water or shrinks, you’ll never need to worry about all these distortions and more with uPVC. No painting, no sanding and ultimately, low maintenance required.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.