Find a Builder you can trust in Gwynedd.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

With the numerous benefits that comes with the installation of an external wall insulation in a building, it’s also important to find out whether it’s also safe before proceeding to fit one in your home. Firstly, to ensure that external wall insulation systems are safe, they must be BBA approved, which means they’ve been subjected to a thorough testing by the British Board of Agrement and therefore, suitable for use in UK homes.

Given the fact that cladding materials have recently generated a lot of debate and negative press about how reliable some particular materials are, questions are being asked of the safety and reliability of external wall insulation. However we must clarify that, although external wall insulation can be classified under cladding, it is very different to rainscreen cladding - which caused the Grenfell fire tragedy.

External wall insulation is completely safe. However, when it comes to fire, the safety of your system depends largely on the insulation type in question. The safest type of insulation you can have installed is the Rockwool insulation boards which are rated as Euroclass A1 non-combustible. The board is specially designed in such a way that it contains fire - preventing it from reaching the other areas of the building. They also do not produce harmful emission or smoke when impacted by fire.

Meanwhile, the Wood Fibre, is also a great insulation which is known to char and not burn. Contrary to many beliefs, it actually burns slowly creating this charring effect which produces an oxygen barrier that helps reduce the spread of fire.

To make your system safer, you can also make use of Fibreglass Mesh for reinforcement. It helps to improve the strength of the tensile which promotes the security of the boards attached to the wall.

A dormer loft conversion is a type of loft conversion that’s built making use of a roof’s existing slope. In other words, it’s an existing roof’s extension which is constructed in such a way that allows for an additional floor as well as head room especially suitable for lofts lacking good amount of usable space. The dormer loft conversion is simply an addition to the existing roof looking much like a box-like build constructed onto a pitched roof as it creates walls that are vertical to the slope while also being 90 degrees to the floor.

This type of loft conversion is the most common amongst homeowners in the UK mainly because it represents a cost effective means through which you can add an additional usable space to your home or property. The structure extends for the slope of the existing roof and can easily be altered to suit various tastes or styles. Furthermore, if you’re looking for a type of loft conversion that aids to foster reduced disruption to work, then dormer loft conversion is also your best bet. This is due to the fact that the structure is built from a scaffolding made outside a home.

There are different types of dormer loft conversion and the one which will best suit your property will depend on the property type, be it detached, semi detached or terraced as well as the existing roof shape and size. The dormer loft conversion is a popular choice for a lot of homeowners for a variety of reasons. Let’s have a look!

✓ It’s very cost effective

✓ The dormer loft conversion does not require planning permission so far it complies with certain conditions and limitations

✓ It adds an extra headspace as well as floor space.

How Much Does A Loft Room Cost

In the event whereby you happen to run out of space in your home and extending sideways or moving out isn’t even a considerable option, the next best solution is to look upwards - the loft. The loft can be converted into a room that can used to satisfy varying purposes, be it a storage room, bedroom, home office, spare bathroom and more. There are a number of loft conversion styles you can go for including a room in loft conversion, dormer style conversion, mansard conversion, or a hip-to-gable conversion. Regardless of your choice, each of the types will not only give you new rooms to enjoy but also add value to your home. However, before getting started, it’s crucial to have an idea of the loft conversion cost to help you prepare a budget and begin planning. Here, you’ll discover the most likely loft room cost for each conversion style you opt for.

• Room In Loft Conversion

This is only suitable for some specific home, but it’s however the most affordable option of the lots. This loft conversion style will cost within the range of £15,000 to £20,000 (prices can be higher in regions where tradesmen are higher in demand such as London and the south east).

• Dormer Loft Conversion

These are relatively simple and straightforward to include in your home. The cost ranges between £31,000 to £58,000 depending on the conversion’s size and other factors.

• Hip To Gable Loft Conversion

This style of loft conversion is more complex than the aforementioned ones, hence they’re usually more costly to complete. The price ranges between £42,000 to £65,000.

• Mansard Loft Conversion

This style of loft conversion is the most complex of the lot and includes a complete overhaul of your loft. The price ranges between £45,000 to £70,000.

• Bungalow Loft Conversion

Any of the main styles above can be done to a bungalow if the planning requirements are fully complied with and if the property is suitable. The price ranges between £30,000 to £70,000.

It’s a fact that a garage conversion can go a long way to add a resale value to a home or property. Therefore, in the event whereby your home already has parking facilities in place you can put into consideration converting your garage into a habitable space which will add to the sales price of the house by adding an extra room or increasing the floor space. So exactly how much does a garage conversion add to your home’s resale value?

Garage conversions can be seen as a cost effective means of adding more space to your house. However, not only does it add space, but can also add up to 20 percent to the value of your home. It’s also a way of adding an extra living space to your home that’s not under strict planning complication unlike the alternatives. Generally, if your garage happens to be connected to your house, the cost of converting it to another room should between £10,000 to £20,000. As a home owner, converting your garage into an extra room can help increase the value of your home by up to £45,000. And if you’re to comply with the set rules under permitted development rights, you may not even require to submit a planning application.

In the event whereby your garage is detached from your house or perhaps you live in a flat ( or maisonette) or a listed building , you’ll need to apply to the local authority before commencing your project. It’s always wise to check if there aren’t any planning conditions attached to your home or property.

Sand is a very important element in bricklaying as far as a mortar mix is concerned. Generally, the quality of the sand is the major factor determining the quality of a plaster mix or mortar mix. It’s recommended that the sand should have enough ‘fines’ (- 75 micron material) to get a good plastic mix with a water content that’s less than 350 litres/m3. Generally, a mortar mix or plaster mix is made within the range of one bag of cement to 200 to 300 litres of damp sand.

Apart from experience the next best indicator of the quality of sand is a field test. In other words, if you do not have the required training or experience in bricklaying, the best bet to determine the amount of sand for a good quality mix is by carrying out a field test. Let’s have a look!

• Get about 50kg of sand and air dry it.

• Scoop 25kg of the sand, 5 kg of cement as well as litres of water ( with 1 litre and 1.5 litres of the water in different containers).

• Mix the cement and sand to form a smooth, uniform and consistent colour.

• One after the other, mix the the sand - cement mixture in the three quantities of water. Do this until you’re able to achieve a mix that’s workable enough to use as plaster.

With that done, you should take note that if 5 litres of water is sufficient then the quality and quantity of the sand is perfect. If you’d require 6 litres of water to get a mix workable as a plaster, then both the quality and quantity of the sand is average. However, if you’d need 7 litres of water to get a mix workable as a plaster, then the quality of the sand is poor. Any requirement of water above 7 litres implies a very poor quality of sand.

How To Put Up Plasterboard

Putting up a plasterboard is a vital process when it comes to home renovations. However as daunting as it may seem, with a good guide and regular practice you can master the skill within a small period of time. If you lack proper training and experience, we’d recommend you hire a seasoned professional plasterer for help so as to get the best result and also avoid additional costs due to possible damages.

Putting up plasterboard is way quicker than wet plastering and also significantly reduces the drying time that can slow down your renovation plans. With a plasterboard, you can delve straight into the decorating stage and achieve a smooth finish. Below are the steps required to put up a plasterboard.

• The first step is cutting the plasterboard to shape which be one of the most challenging parts of the process. This is because you’ll need to fit the board around things such as plug sockets and window sills. As a result, this involves cutting complex shapes rather than just a simple straight line. To get this done, simply mark out the cut required with the use of a tape measure, combination square and spirit level for a better precision. Once done, you can then use a plasterboard pad saw to cut along the marked spots.

• After you made the required cuts, the next step is putting up the plasterboard. And depending on where the boards are going to be put, this could be a very challenging task. If you’re going to put the boards on the ceiling or somewhere very high up, you’d probably need an extra pair of hands for help. To get this done, use the appropriate screws to secure the boards in place if you’re installing them directly on studs. However, if you’d be fixing them onto bricks or blocks, a drywall adhesive is your best bet.