Find a Builder you can trust in Berkeley.

There are so many benefits that comes with building a porch in your home premises. It’s an extra space where a lot can be achieved such as drying a dripping wet dog, taking off your dirty shoes or boot and lots more. So if you’re considering to construct a porch, it’s definitely going to be a wise decision. However, before you get started, there’s a need to determine if you’ll need planning permission for a porch. It’s important to take note that planning laws are dynamic and can be updated at any point, so be sure only to use trusted sources only as your guide. If you’re the homeowner or landlord, it’s entirely your responsibility to obtain the right approval for any development project you wish to carry out within your premises.

A Porch can not be termed as an extension and neither is it a conservatory, they’re basically built to the home’s front covering the main entrance using a stone base or a brick. As a result, a porch does not need planning permission due to the fact that it’s covered by the permitted development rights if the specific guidelines for porches are complied with. Below are the instances where you WILL need planning permission for a porch.

✓ If the floor space is more than 3sqm (the wall inclusive).

✓ The highest point has a height of more than 3 metres.

✓ If the porch is situated within 2 metres of a boundary directly facing on to the road.

You may need planning permission if the house is a listed building, designated area or falls under an Article 4 Direction.

In order to build a porch without planning permission, you need to consider all the criteria stated above. You can also visit the Planning Portal website to get more detailed information before getting started.

Due to the fact that we live in a country (the UK) with so much history as well as architectural beauty, there’s a need to have what’s commonly called “Conservation Area. A Conservation Area is basically an area which is designated by the local authority and is established in order to protect and enhance areas of historical and architectural interest which includes both rural and urban areas. Therefore, when it comes to refurbishment project in a conservation area, there’s usually a lot of things that needs to be put into consideration as well as hurdles to scale in order to make alterations to your property without any interruptions from the law.

In general, all properties in a conservation area have strict regulations governing the outlook of the houses, as this plays a major role in the appearance of the area as a whole. As a result, if you wish to bring down a building, fence, wall or even railing and the likes, you’ll need to obtain prior consent before you proceed. An easy way to go about any refurbishment plan is to to ensure the usage of exactly the same materials that exists in the current house. When you abide by the rules, you’ll be in a more favourable position to acquire the needed prior consent.

The short and simple answer to the question is yes, you can refurbish a house in a conservation area but subject to the approval of the local authority through a planning permission. And when it comes to submitting a planning application for approval, some are aspects will usually be subjected to more intense examinations than the others. Hence, the need to make sure that your refurbishment plans are all friendly in a similar way to the neighbouring buildings and environment.

It shouldn’t do. Most companies will do all the interior work first, and the last job to do will be creating the opening from the house to the conversion. A reputable company will make sure they cause as little disruption as possible during this time.

How Much To Board A Loft?

If you stay in a building where the space meant for storing stuffs is not sufficient, boarding your loft may be just the perfect solution for you. In several homes, the space is already present, and all you have to do is to make it more usable by boarding it out. This is unarguably one of the easiest and quickest ways to create storage space in your home.

Boarding a loft comes with a number of special benefits which includes:

• Assisting to declutter our living spaces and makes for a more spacious home.

• Creating a usable space whereby all seasonal items can be stored.

• Assisting to reduce heating bills as it prevents the loss of heat. When your loft is well boarded and insulated, it’ll help trap heat and prevent it from escaping via the roof.

• Adding to your home’s value by making your attic a very useful space for storing items.

• Helping to create a quiet space which can used for relaxation or getaway purposes and of course, this will require a bit more structural work.

So now that you’ve learnt a few of the benefits associated with boarding a loft, how much will it cost to have one made? This depends on an array of factors which includes the size of the space needed, the type of materials and labour cost.

Overall, a standard semi detached building will feature a lot of space of about 40 sqm to 50 sqm in size. There’ll be a need to add to the height of the floor joists before installing the chipboard decking boards. This job size should cost within the range of £1,000 to £1,500. It’ll require just a two-person team that are fully equipped and well versed about the processes.

When thinking about the right insulation material for your loft, some of the first few things that comes to mind is the various properties of that material as well as how good they fit with your home’s needs.naturally, you’d like to ensure that the insulation will be efficient enough to add to the overall energy efficiency of your home, however there are also other features that may not get as much attention but also happens to be equally important. As the primary function of an insulation is to blanket your house to offer a barrier against heat loss, going for an insulation material that’s also fireproof is crucial as loft insulation can burn. Although most insulation materials are fireproof, a myriad of problems can actually make your insulation burn.

For instance, fibreglass insulation is produced using glass combined with plastic polymers and is naturally resistant to fire. However, even at that you’d have to be careful with batts that are supported with foil or paper due to the fact that these materials can burn pretty quickly. Cellulose, on the other hand, is not fireproof and is required to be treated by other flame retardants in order to help reduce combustion. Some of the best insulation materials that are resistant to fire includes the following:

• Fibre glass. This is made of glass that’s spun into fibres, then combined using plastic polymers. As a result, fiberglass insulation is naturally resistant to fire.
• Mineral wool. Having a high melting temperature, this insulation material happens to be a great fit for thermal applications due to its superior fire resistant properties. In fact, mineral wool is still naturally non-combustible even if composed of recycled iron and steel by-products, or from actual mineral rock itself.

A barn conversion is where an agricultural building is altered to serve a different purpose. Lots of barns conversion projects involve converting an old barn into one or more homes. However, barns can also be converted into other types of commercial building, like offices.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the ours so that you can find quality tradespeople and see genuine reviews from previous customers. Not all online review sites can be trusted to display real reviews.

Did you try rendering a wall but it doesn’t turn out the way you would have hoped for? Or perhaps you’ve been watching your wall render gradually deteriorate over time. Regard of your purpose, learning how to repair render cracks on wall is usually a great skill to have with your home maintenance in mind. However, whenever these crack are too large or difficult, we’d recommend you call in a reliable professional who can guarantee the best results for help. In this guide, we’re going to take you through the wall render repairing process. Let’s have a look!

No matter how solid a building material is, over time it’ll yield to the elements. When it comes to wall rendering it may be a case of too much sunshine or a costly mistake in the application process, but in truth, it cracks just because it cracks.

In order to repair render cracks, you’d have to start with a removal of damaged or cracked render. You’ll have to remove all the render or just a small section depending on the area you’re working on. If you’re able to clean all of the existing render as well as the paint over it all (both old and new), then removing a small section would work better as it makes it look neat and redone. Upon the removal of the existing render, the next important step would be to remove all loose material as well. Once done, you can then leave for up to 2 days to allow any trapped moisture to come out. Unfortunately, if the rains you’d have to wait till that dries too before you proceed.

Once dried, you can buy a pre-prepared render mix which already contains cement, lime and sand. Mix a 20kg bag with 4 litres of water (or check the product instructions and follow strictly), the mix to a fine consistency. Render is quick to dry, so you’d want to apply within 30 minutes of mixing. Make use of a trowel to apply the render on the affected spots and blend with the surrounding area.