Find a Builder you can trust in Hockley.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

Storage space is a major consideration for most home buyers and even more so, when there’s the presence of fitted wardrobes. Fitted wardrobes can be installed in just about any room in the house and even in rather obscure places such as under the stairs, inside a loft, around chimneys as well as into alcoves. As a result, they’re important assets to have as they can go a long way to increase the value of your home or property.

Fitted wardrobes are usually made from various types of woods as well as wood finishes. Typically, they’re installed with either sliding or hinged doors depending on the space as well as the styling you opt for. Fitted wardrobes can be personalized through the addition of elegant features such as custom lighting, mirrors as well as internal extras like pull out shoe racks and pull down hanging rails.

For high end customized fitted wardrobe like Sharps, the best quality, most practical and also robust materials are being incorporated. They make use of the following materials given below:

✓ Fibreboard. This is a modern material that’s used for its ability to produce a smooth routed and detailed design. It’s also very solid and robust which makes it perfect for large furniture pieces as they don’t warp or dent. What’s more? Fibreboards meets the European forestry sustainability standards and it also allows for the board to be profiled with a top notch finish.

✓ Particleboard. This material is used for the parts of the furniture which will normally be cut in your home like facings and side panels. Due to it’s lightweight, they’re very easy to cut and doesn’t produce as much dust as other materials. The material is also a highly controllable contemporary material which can be precisely cut arounf skirting boards, covings as well as period features to ensure a perfect fit.

How To Convert Your Loft Into A Room

The loft is the space on top of a home that’s most often ignored by home owners due to having to consider the space’s configuration, the lighting as well as energy efficiency. However, when successfully converted into a room, it can serve several purposes which would even add more value to your property. So how can you convert your loft into a room? Let’s have a look.

• Take Into Account The Size Of Your Loft

The size of your loft is a major determinant of the type of room it can be converted into. A small-sized loft there’s a chance it can still be converted into an extra bathroom or home office while bigger lofts can be converted into an additional bedroom. The minimum head height is 2.3m, if your loft is lower than this, you’d have to get a planning permission to detach some parts of the room for extension.

• Include A Skylight

When a loft is poorly designed, the room become dark, shady and airless. Adding a skylight to your loft will let in fresh air, deliver better ventilation and more light.

• Insulate Your Loft

Loft insulation will not only prevent heat from escaping through the roof, but also lead to an improved energy efficiency which ultimately helps you save up on your heating bills.

• Use Modern Colourization

When you use bright, neutral and modern colours to paint your loft, you’re adding that elegant look to the space. As a result, the loft looks a lot more attractive and comfortable by the time you’re done with the conversion.

The conversion of your loft into a room can be a very tedious task if you wish to do it by yourself. We’d recommend you employ a seasoned professional for help in order to ensure the best results and also to avoid making costly mistakes.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the Federation of Master Builders. They have a search tool where you can find precise crafts in your area and look at their situations. All FMB members are assessed and individualistically examined and are checked to ensure that they have the correct insurances in place.

If you’re planning to construct a kitchen diner extension, to help you set a budget and start planning you must first have a cost estimate that’ll complete the entire project. If not, there’s a probability that you may have to spend more than would have been necessary or probably break the bank to have the project done. In truth, there’s no single and short answer to this question as the cost of a kitchen diner is largely dependent of several variables. In this article, we’re going to give a good insight into kitchen diner extension cost so as to help you make informed decisions moving forward. Let’s take a look!

On the average, a kitchen diner extension will cost within the range of £25,000 to about £45,000, however if you happen to reside in London, you can expect the cost to be a lot more than that - closer to £60,000. And due to the fact that there happens to be a plethora of options out there, any decision to make be it on the size, tradesman, flooring, finishes or type of the kitchen diner extension, will have a considerable impact on the overall cost of the project. For instance, a basic kitchen diner extension cost can be within the range of £12,000 to about £15,000., while a high end kitchen diner extension can reach a whooping price between £80,000 to about £100,000.

The total cost of your kitchen diner project will rely heavily of the size as well as the quality of the finishes. For example, a kitchen diner extension that’s small and basic is likely to cost about £1,300 to £1,500 per square metre. However, if you’re going for higher quality finishes, you can expect to pay within the range of £1,900 to about £3,000 per square metre.

How To Repair A Pothole In Gravel Driveways

When the integrity of your gravel driveway is impaired not only does it have a negative impact on the curb appeal of your property, but also makes your driveway a danger zone. If your driveway needs to be repaired, you’d simply have to grab the bull by the horn and get it done - the sooner, the better to avoid the problem getting worse and to have your beautiful gravel driveway back as soon as possible.

The major cause of potholes in driveways is usually water, when it gets trapped beneath the surface of the driveway. Therefore, you may also want to enhance the drainage in the area as part of your repair. The repair process is quite simple for confident do-it-yourselfers, but if otherwise, then calling in a reliable professional will save you some time and extra money that can result from possible errors. So how do you repair gravel driveway potholes?

✓ Prepare the area. This involves removing all forms of debris from the pothole. To achieve this, you can rake, shovel or brush the loose stones, soil and other debris from the pothole.

✓ Fill the pot hole. Make use of a coarse gravel to fill up the pothole to a depth of about 3 inches beneath the driveway’s level. Upon the filling, simply tamp down the coarse gravel using a commercial tamper or any available homemade option. Once done, the final 3 inches to the surface of the gravel driveway should then be filled up with gravel which perfectly matches the colour and texture of the remaining driveway.

✓ Compact the patch. To achieve this in an easy and fast way, simply run your car’s wheel up and down over the repaired spot gently a couple of times. This will be enough to compact the patch and seal the pothole.