Find a Builder you can trust in Tranent.

Sand is a very important element in bricklaying as far as a mortar mix is concerned. Generally, the quality of the sand is the major factor determining the quality of a plaster mix or mortar mix. It’s recommended that the sand should have enough ‘fines’ (- 75 micron material) to get a good plastic mix with a water content that’s less than 350 litres/m3. Generally, a mortar mix or plaster mix is made within the range of one bag of cement to 200 to 300 litres of damp sand.

Apart from experience the next best indicator of the quality of sand is a field test. In other words, if you do not have the required training or experience in bricklaying, the best bet to determine the amount of sand for a good quality mix is by carrying out a field test. Let’s have a look!

• Get about 50kg of sand and air dry it.

• Scoop 25kg of the sand, 5 kg of cement as well as litres of water ( with 1 litre and 1.5 litres of the water in different containers).

• Mix the cement and sand to form a smooth, uniform and consistent colour.

• One after the other, mix the the sand - cement mixture in the three quantities of water. Do this until you’re able to achieve a mix that’s workable enough to use as plaster.

With that done, you should take note that if 5 litres of water is sufficient then the quality and quantity of the sand is perfect. If you’d require 6 litres of water to get a mix workable as a plaster, then both the quality and quantity of the sand is average. However, if you’d need 7 litres of water to get a mix workable as a plaster, then the quality of the sand is poor. Any requirement of water above 7 litres implies a very poor quality of sand.

If your basement has a cavity drain membrane, it’ll need a pump to move water away from the exterior of your basement and prevent flooding.

Sump pumps can be noisy, but they don’t have to be. Generally, if you have a well-designed pump that’s installed correctly, you shouldn’t find it a problem. For best results, hire a skilled, experienced professional to supply and install your drainage system.

The main reason that people use cladding or rendering on their property is the aesthetic benefit. These materials can really boost the appearance of a home. Cladding and rendering can also increase the thermal performance of a property. Speak to a specialist to find out whether your property will benefit.

One of the main reasons why fitted wardrobes are a popular choice amongst homeowners is due to the fact that they’re able to help maximise storage space and since they’re usually customized for the particular room, they’re always good looking. However, just like any other home item, over time your installed wardrobe may start to look a bit dated and old fashioned. In these type of events and in order to save money, several homeowners would prefer to update its look to a more modern one without having to completely replace the fitted wardrobe with a new one. In this guide, we’ll give some great tips on how to update your old fitted wardrobe. Let’s take a look!

✓ Add mirrors to the wardrobe doors. Your old fitted wardrobe may be made of old fashioned laminate or chipboard which happens to draw scratches and dents here and there. If this is the case, you can simply add mirrors to help conceal the damage or unsightly marks.

✓ Include decorative trimming or panelling. You can choose from the various styles of trimmings you’ll find at hardware stores. By adding some strips of moulding, the whole look of your fitted wardrobe can change significantly.

✓ Painting. If the surface of the wardrobe permits, painting can go a long way to alter the look of the wardrobe.

✓ Change the handles. Handles may seem as a little item that doesn’t add to the aesthetics of the wardrobe. However, in reality, change your old handle with a more modern and fashionable one can make a great difference to the wardrobe’s overall appearance.

✓ Upgrade the interior. You can upgrade the interior of your wardrobe to give you more options and a better appearance. For instance, you may wish to have part of the wardrobe to offer integrated shelving or perhaps pull out drawers rather than having all the interior space for hanging clothes and garments.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

How To Plasterboard A Brick Wall

Do you want to cover your brick wall with plasterboard? The key to success here is the preparation. You must ensure that brick wall is prepared well enough to receive the plasterboard. To get started, there’s the need to attach wood furring strips to the wall which serves as studs in a wood frame structure. This way, the plasterboard will be prevented from getting in touch with the brick. You can always hang pictures or any other forms of decoration in between the gap between the walls. Let’s have a look!

lAttach Furring Strips

• Get a 2 inch by 4 inch wood stud and apply a bead of construction adhesive.

• Using a masonry bit, drill a pilot hole through the wood stud’s base as well as the brick wall.

• Hit a 3 inch fluted nail through the hole using a sledgehammer

• Using a construction adhesive, bind a horizontal 2 inch by 3 inch stud to the upper edge of the wall.

• Using an adhesive, bind the length of a 2 inch by 3 inch stud on its wide side.

• Use a masonry drill to drill a hole on the wood stud and 1 1/2 inches into the brick wall.

• Hit a 3 inch fluted nail through the pilot hole.

lApply Plasterboard

• Hold a plasterboard sheet against the furring strips.

• Use plasterboard screw to hold the drywall sheets in place.

• Use fibreglass to cover the joints where the two plasterboard sheets meet.

• Use a thin layer of the joint compound on the tape. Once done, screw it using a 6 inch taping knife, then allow to dry overnight.

• Use a sandpaper to smooth the joint compound.

• Use a fresh coat of the joint compound to block the holes and joints. Once done, allow the compound to dry.

• Use a light sandpaper to smooth the final coat.

Plasterboarding a brick wall is a simple task but the preparation part must be done right to protect your investment. Therefore, we’d recommend you hire the services of a skilful professional, who can guarantee the best results especially if you lack enough training and experience to carry out a DIY project.

Laying of bricks is a skilful trade which requires the bricklayer to fully understand the process involved in the required building material preparation necessary to construct a foundation as well as to mix the concrete or mortar. As a tradesperson, you also need to fully comprehend how to make use of various materials and master the art of shaping, polishing and cutting it. A typical bricklaying endeavour is expected to include different activities such as preparation of the surface, assembly, installation, reinforcement as well as repair.

As a result, every aspect of the job demands an in depth and extensive knowledge, skills and also experience. To get started in this career path, you can also consider getting a bricklaying license as this will stand you out from the lots from your customer’s point of view. However, to obtain a bricklaying license, you’ll need to have some qualifications which includes an industry experience in the field as well as a trade certificate. These formal and nationally recognized qualifications can be gotten through the Recognition of Prior Learning.

It must, however, be said that several states will require either a building practitioner registration or a bricklaying license to enable you practice as a professional bricklayer in order to ensure that the national standards for quality is always met. In other states, a bricklayer must meet some certain registration requirements or possess concrete licenses. Some will necessitate that you register as a building practitioner to take on certain projects but only to a particular level.

Overall, a bricklaying license will help you meet the building commission’s requirements so as to avoid stern punishments like fines and sanctions. It also allows you to sign legal contracts and agreements, market your services and lots more to steer ahead of competition in the industry.