Find a Builder you can trust in Humbie.

If you’re planning on adding a house extension to your property, you’d probably be worried about whether or not your proposed extension would require a planing permission. Well, it may be relieving to know that not every house extension project would require a formal consent, and in fact, several extensions are covered by the permitted development rights. Not only can this save you a considerable amount of time especially at the project’s planning phase, but it’ll also save you money on the application fee. In the UK, single storey extensions to the house’s rear can be 3 metres deep for both semi detached houses and terraces or 8 metres deep for detached homes.

So how do you know when you’d require a planning permission for your home extension? Well, if your extension plan fits these criteria explained below, then your project is most likely going to be allowable as a permitted development.

• Extensions, which includes previous additions, must not go beyond half of the original house’s total surrounding land area.

• The main elevation, or side elevation where it fronts the highway, must not be extended forward.

• For single storeys, the rear additions must not extend more than the original house’s rear by more than 3 metres in both semi attached homes and terraces (4 metres for detached houses).

• Extensions to the side must be a single storey with a height not exceeding 4 metres and not going beyond 50% of the original house’s width.

• Extensions hat within 2 metres of a boundary should have a eaves height not more than 3 metres.

• Multi storey addition must not extend beyond the original house’s rear wall by a maximum of 3 metres or 7 metres of the boundary opposite the rear wall.

• Permitted development rights do not apply in listed buildings or designated areas.

If you’re considering converting a barn or buying one, you shouldn’t need to worry about it being cold. This is because building regulations dictate that when you convert a barn, you need to insulate it to meet specific standards. However, it’s worth considering its heating system and ceiling heights carefully – some barn conversions are likely to take longer and be more expensive to heat up than others.

External Wall Insulation (EWI) is the act of insulating a home by fitting insulation to the exterior parts of the building which in turn improves thermal performance, cuts energy consumption ( savings on energy bill) and also adds to the home’s visual appeal. The systems are built in multiple layers, with the insulation board offering a plethora of options with each being suitable to varying projects and their needs. Installing an external wall insulation comes with a variety of benefits, let’s have a look!

• Thermal Performance Improvement

With EWI, the thermal inertia of the walls are greatly enhanced while also restricting the loss of heat. Ultimately, this lowers heating costs, enhances the comfort of indoor thermal and also reduces CO2 pollution.

• Eliminates Noise Pollution

When the noise levels are high, it can have a bad impact on our overall well being. A great way to reduce the disturbances from the outside like traffic noise is by fitting an External Wall Installation system.

• More Comfortable Living Space

Do you know the damp in homes can contribute to respiratory problems? A properly insulated home will greatly limit the impact of condensation by combating the damp issues. As a result, you can always expect your house to be cosy and comfy irrespective of the season. A cooler summer and warmer spring is guaranteed with EWI.

• Enhances The Property’s Visual Appeal

Looking for an excuse to rejuvenate your home’s aesthetic appeal? Well, you can as well try out adding an EWI system. There are a plethora of unique colours and styles you can pick from to beautify your home effortlessly.

• Adds Value To Property

An insulated home will generally cost more than an uninsulated one at the time of resale. Potential home buyers are more interested in the acquisition of a home with an EWI system due to its various benefits - and a higher demand can only imply a higher price!

Refurbishing a house brings about a plethora of benefits. These includes an increased sale value, an improvement on your quality of life or even simply to make it more visually appealing. All these are great when you look at them, but one thing that happens to be an hindrance for several homeowners is the cost of getting the project done. You may wish to set a budget, plan and prepare before commencement of the project, but the fact remains that, when it comes to refurbishing a house, nothing is certain. In fact, it’s advised to always expect the unexpected and have a lot of cash in reserve just in case something goes wrong. There are a wide range of factors that can play a key role in the overall cost of a house refurbishment. Minor refurbishment that should cost around £30,000 can easily go up to over a whooping £150,000 for a total transformation. Most of this cost will be expended on labour, and the next most significant expense, which is sourcing materials.

In general, the cost of your refurbishment project will depend on some factors which includes the size of the project, the materials used, the refurbishment or renovation level, the location of the property, the quality of the contractor hired and lots more. To estimate the cost of refurbishing your property, you can follow these simple steps:

✓ Write down a detailed list of all the things that needs to be done per room and try to be as specific as possible.

✓ Carry out a research of the labour cost in your area as well as the raw materials’ cost (here, you can make use of guides such as home advisor).

✓ Add an extra 10 to 15 percent on top of the calculated estimate for uprisings and repairs.

✓ Talk to your contractor to get a more accurate quote.

Pebble dash is an effective way to tune up your house or property as it can go a long way to enhance its curb appeal while also add to its resale value if you should decide to sell later on. Although, it’s highly recommended to leave this task for a reputable specialist, it’s also something that can be done as a DIY task. It must be states that this is a pretty difficult job and even more so if you haven’t attempted it before. In this post we’re going to take you through the processes involved in pebble dashing a wall. Let’s take a look!

• Mix up water with the lime strictly following the manufacturer’s instructions. Once done, leave it covered up to hydrate for at least 24 hours.
• Take one part of the slaked lime and mix it up with cement and six parts sand. This is to give the base mixture required to spread onto the surface.
• Use a trowel to apply the mixture onto the wall. Ensure that the trowel is level and use the edges to make a flat and smooth layer of the mixture on the surface as a base layer. Allow the base layer to dry for up to an hour. Then, rake the surface using a notched trowel and allow to dry for a minimum of 24 hours.
• Rinse and drain your pebbles. Then, set them under the wall you’re pebble dashing.
• Take the top coat of five parts sand and mix with one part cement and one part slaked lime. Use a trowel to apply this mixture over the base layer and smoothen it with the trowel to create a flat and even top layer.
• Spread a plastic sheet beneath the wall you’re pebble dashing to capture any loose pebbles as they fall.
• Grab the bucket of pebbles below the wall and scoop some of the pebbles up using a scoop or trowel. Some will stick and some will fall into the plastic sheet already placed below. Continue throwing the pebble dash until the surface is completely and evenly covered with pebbles.
• Lightly press and fit the pebbles on each section into the wall and leave for at least 24 hours to dry.

How Much Plasterboard Do I Need?

Although many people especially contractors have a tough time estimating the number of drywall or plasterboard needed to complete a project, it’s a rather simple task if all factors are taken into consideration. If you’re able to follow the same procedures taken by professionals to count dry wall sheets, you’ll be in the right direction. Let’s have a look at the procedures to follow!

lTake Square Footage Measurement

• Measure the square footage of the area where the plasterboard will be fitted.

• Multiply the height by the width of each wall or ceiling area.

• Add all quantities to obtain a total square-foot amount.

lCalculate Drywall Sheets

• To calculate the number of drywall or plasterboard sheet is very simple once you’ve gotten the total square footage.

• To get started, simply divide the total square footage of area by 32 (that’s if you are using a 4 by 8 sheets) or you can also make use of 48 to make the division (only if you’re making use of the 4 by 12 sheets).

• The answer you get after the division will give you the full number of plasterboard sheets that’s required to complete the project.

We’d recommend you include an extra 10 to 15 percent of whatever you calculate to take care of the possible odd cuts and wastages. This implies that if your total area is 1600 square feet while incorporating 4 by 8 sheets, simply divide 1600 by 32 which equals 50 sheets, now take 10% of 50 which equals 5, then add back the 5 extra to the 50 sheets earlier calculated to get 55 sheets. If you wish to estimate the cost, simply multiply the number of sheets gotten by the price per sheet. Do not forget to include delivery charges and local taxes.

When it comes to house renovation costs, nothing is certain. As a rule of thumb, you should always expect the unexpected. Unforeseen circumstances (mostly unfavourable) can crop up from anywhere, at any time, greatly affecting the cost of the project. However, if you’ve completed proper planning and done your due diligence on your property before commencement, there’s absolutely no reason why you can’t put the works on budget.

The cost of a house renovation project depends on a lot of variables. These variables include the type of property you’re undertaking as well as the amount and complexity of the entire project. What’s more? Whether you decide to do some of the work yourself or wish to hire quality tradespeople to cover the entire project will also tell on the cost of the home renovation.

In the event whereby you wish to completely gut your property and begin from square one, here are some of the cost you’re most likely going to incur:

✓ Planning applications and building controls

✓ Architect’s design and specifications

✓ Contractors and build costs

✓ Snags as well as unforeseen problems

What will be the biggest cost, which will be determined by the amount of work you need done, is most likely going to be the structural and building work, which can reach up to tens of thousands of pounds.

Asides from material and labour, the administrative costs is another important cost you’ll need to factor in. The first thing here is usually insurance, this is because all regular building insurance policies does not cover large scale renovation projects. So if what you’re planning is a huge structural change to your property, then it’s more likely that it won’t be covered by your buildings insurance policy. In this event, you’ll have to take out a specialist renovation insurance.

Finding a builder nearby can have enormous assistance when it comes to your build. Period on site, their familiarity of local planning permission, constructors’ dealers and other local trades are all vital bits of knowledge that you’ll welcome on site.

It is always wise to walk around in your local area or drive to a site where any construction work is going on. It’ll give you a proper impression of the constructors who are active nearby. You don’t have to like their style of work or the project they are currently carrying out – after all, a builder can only produce what’s on the plans in front of them.

Find a Builder Other Tradesmen Recommend

If you’ve had to call an electrician before or a local plumber and liked their work, you can always ask them if they have any builders whom they would recommend. Maximum tradesmen get used to seeing the similar acquainted names from one place to another in the sites they are working on and every so often has favourites for who they like to work with — and who they see as a good source of work.

Always Talk to Previous Customers

Once you’ve found a builder you would like to work with, ask them for a list of previous customers they have worked with; they ought to be glad to offer particulars if they’re self-assured they’ve done an effective job.

Look for a builder online

A decent place to start looking for builders online is on sites like the Federation of Master Builders. They have a search tool where you can find precise crafts in your area and look at their situations. All FMB members are assessed and individualistically examined and are checked to ensure that they have the correct insurances in place.