Find a Builder you can trust in Tregaron.

How To Dot And Dab A Plasterboard

If you want a fast and simple way to achieve a smooth and sturdy wall which is decoration-ready, then dot and dab plasterboard is the way to go! It’s a relative simple process but can also be a bit challenging. Therefore, if you lack the necessary training or experience, hiring a professional would be a great step to protect your investment and guarantee the best results. Here, we’ll provide you with a deep insight into the plasterboard’s dot and dab procedures. Let’s have a look!

• At the thickness of the board with the adhesive, mark the ceiling and floor as well as the wall to indicate the centre of each board.

• Ensure the wall’s height is 15mm more than the plasterboard

• Make a mixture of the adhesive and achieve a thick consistency. Apply a consistent layer of the mixture around the wall’s perimeter, edge of the ceiling and any other openings with the use of a trowel.

• Select dabs that are about 250mm long and 50mm to 75mm wide and apply the adhesive in them. Make use of 3 vertical rows for individual boards. Also ensure to apply, at skirting level, a band of adhesive.

• Position the board’s reverse side against the dabs, and laying against the packers. Then make the board align with the ceiling and floor marks with the help of a straight edge.

• Raise the board till its tight against the ceiling with a board lifter. Once done, use the plasterboard to wedge the board into place before you remove the board lifter.

• Repeat the same process for the remaining parts of the room. Once completed, make sure the adhesive is set before you remove the boards.

Over the years there has been an increase in the recommended thickness of loft insulation by the government. Obviously, the reason behind this is pretty simply - the thicker the layer of your loft insulation the bigger your savings. The UK government is very keen to every house in the country to have loft insulation fitted where possible as it helps to minimize the heating demands of these properties. Households get to benefit from loft insulation in so many ways which includes reduced energy energy bills as well as having a home that stays at a more comfortable temperature for longer.

Generally, for the government energy efficiency is crucial as it implies that the highest demand ( which is usually the time of the day when gas or electricity use is at its peak ) reduces, since each building requires slightly less energy. Overall, that ultimately implies that new power plants don’t have to be built which is some nice cost savings for the government.

In the 1980’s, any thickness of loft insulation from 25 mm to 50 mm was considered the standard. But then, building regulations stated that homes should have as much as 100 mm of loft insulation. Over time, this gradually increased to 270mm for new builds and also recommended for other properties, although not essential. As a result of this, there’s always a need to check how much insulation you currently have in your loft before you decide to purchase more. You may discover that you already have something within the range of 20 mm to 200 mm up there and knowing this and the insulation values will assist in determining how much more you’ll need to purchase, if any at all. You should also note that some modern materials can offer the same thermal insulation whilst not being as thick.

Damp issues on a property are usually generated by a lot of factors such as a poor or broken guttering, condensation and lots more. The question arising here is what is the possibility of External Wall Insulation (EWI) preventing condensation? Not only is EWI a reliable way to reduce condensation-caused damp, but it’s also one of the major reasons property owners in solid wall homes consider thermally rendering or cladding their external walls.

Condensation arises as a result of warm moist internal air hitting a cold surface such as the steaming up of both windows and mirror when having a shower. What happens here is the condensation of the water vapour in the air from a gas to liquid in the process of touching the cold surface - one whose temperature is significantly reduced to reach the dew point. At the dew point, condensation is very rampant, and to tackle this issue you’ll have to heighten the wall temperature in order to convert the moisture to vapour and permit it to pass through the wall. And that’s exactly the job of an external wall insulation!

To get started you must ensure that the walls are clean and dry prior to fitting the external wall insulation. The month of May through to September when the weather tends to be dry and more stable are usually the best period to carry out the project. The external wall insulation will function just like a cosy blanket around the building. Ultimately, changing the feel and temperature of the inside of your home. As a result, the previously cold walls will no longer be cold which goes a long way to mitigate the effects of condensation. Furthermore, when an EWI is installed, the rooms of your home will automatically trap more thermal mass as the heat is saved in the walls’ fabric and released back when the temperature drops.

Tiling a porch roof is a very important but laborious and difficult task. A project of this magnitude will require a large investment in planning and preparation way before the actual installation process takes place. It can be a brand new porch roofing tile or a replacement of the existing one, either way it’s crucial to get the right technique. If you lack proper training or experience in this field, we’d recommend you hire the services of a reliable professional probably within your local area to guarantee the best results and to save yourself some time and money. This guide will give you a good insight into the porch roof tiling process. Let’s have a look!

• With the crown looking upwards, put the first tile on the batten and centre the tile from side to side.

• Hammer a 10d nail at the base of the tile and into the batten (make sure not to overdrive the nail).

• To provide a much needed support, apply a little mortar under the first tile.

• Identify the inner end of the first tile and place another tile on top. Take a measurement from the outer end and adjust the end of the second tile to fit.

• Just like you’ve done with the first tile, nail the second tile into the batten.

• Position two tiles at the both ends of the ridge and proceed with the installation just as you’ve done with the previous tiles.

• Take a measurement of the distance across the ridge from the first tile’s outer end. Once done, you can then calculate the number of tiles required by subtracting 16 inches from your measurement and divide the answer by 8.

• Beginning at the second tile on one end of the ridge, install the half the number of ridge tiles towards the centre of the ridge. Now install the remaining tiles working from the opposite end to the ridge’s centre. At the centre of ridge should be a key tile with mortar.

If you’re planning on adding a house extension to your property, you’d probably be worried about whether or not your proposed extension would require a planing permission. Well, it may be relieving to know that not every house extension project would require a formal consent, and in fact, several extensions are covered by the permitted development rights. Not only can this save you a considerable amount of time especially at the project’s planning phase, but it’ll also save you money on the application fee. In the UK, single storey extensions to the house’s rear can be 3 metres deep for both semi detached houses and terraces or 8 metres deep for detached homes.

So how do you know when you’d require a planning permission for your home extension? Well, if your extension plan fits these criteria explained below, then your project is most likely going to be allowable as a permitted development.

• Extensions, which includes previous additions, must not go beyond half of the original house’s total surrounding land area.

• The main elevation, or side elevation where it fronts the highway, must not be extended forward.

• For single storeys, the rear additions must not extend more than the original house’s rear by more than 3 metres in both semi attached homes and terraces (4 metres for detached houses).

• Extensions to the side must be a single storey with a height not exceeding 4 metres and not going beyond 50% of the original house’s width.

• Extensions hat within 2 metres of a boundary should have a eaves height not more than 3 metres.

• Multi storey addition must not extend beyond the original house’s rear wall by a maximum of 3 metres or 7 metres of the boundary opposite the rear wall.

• Permitted development rights do not apply in listed buildings or designated areas.

Storage space is a major consideration for most home buyers and even more so, when there’s the presence of fitted wardrobes. Fitted wardrobes can be installed in just about any room in the house and even in rather obscure places such as under the stairs, inside a loft, around chimneys as well as into alcoves. As a result, they’re important assets to have as they can go a long way to increase the value of your home or property.

Fitted wardrobes are usually made from various types of woods as well as wood finishes. Typically, they’re installed with either sliding or hinged doors depending on the space as well as the styling you opt for. Fitted wardrobes can be personalized through the addition of elegant features such as custom lighting, mirrors as well as internal extras like pull out shoe racks and pull down hanging rails.

For high end customized fitted wardrobe like Sharps, the best quality, most practical and also robust materials are being incorporated. They make use of the following materials given below:

✓ Fibreboard. This is a modern material that’s used for its ability to produce a smooth routed and detailed design. It’s also very solid and robust which makes it perfect for large furniture pieces as they don’t warp or dent. What’s more? Fibreboards meets the European forestry sustainability standards and it also allows for the board to be profiled with a top notch finish.

✓ Particleboard. This material is used for the parts of the furniture which will normally be cut in your home like facings and side panels. Due to it’s lightweight, they’re very easy to cut and doesn’t produce as much dust as other materials. The material is also a highly controllable contemporary material which can be precisely cut arounf skirting boards, covings as well as period features to ensure a perfect fit.

There are many different types of extension. For example, you could install an orangery, flat or pitched roof extension, over-structure extension, single or double storey extension or a glass box extension. Which one of these is most suitable will depend on your existing property.

A lot of an uninsulated property’s heat is lost through the roof and that’s even more alarming, when you realize this figure is up to a quarter of the total heat of the house. Hence, the tremendous importance of preventing this heat loss through loft insulation which will go a long way to help you against spending unnecessary thousands of pounds on heating bill as well as energy loss.

Loft insulation is an effective method to achieve the desired result, however the question is, how exactly does it work? Well, it’s time to find out!

Using either a fireplace or central heating to heat up your home, a large quantity of that heat would be lost through the roof of your home. Generally, heat rises and when it does, there’s simply no way to prevent it - it’s just science. Escaping by both the conduction and convection methods via your roof, the heat escaping through your ceiling, into the loft space and out into the open air outside can only be significantly reduced by laying loft insulation.

Generally, the added layer of insulation works by trapping the heat inside the room below the loft so as to enable the air within your house to stay warmer for longer. What’s more? The layer of insulation also keeps cold air from the outside from entering your home. As a result, you don’t have to heat your home as much in order to achieve the same temperature for each individual room. Over time, just by doing this you can potentially save hundreds pounds. Getting it installed in your home may actually seem a bit expensive at first, but it’s something that’ll eventually pay off.