Find a Builder you can trust in Brixham.

Do you want your house to be built using brick? Or perhaps you just require the professional services of a bricklayer. Regardless of your bricklaying needs, the cost charged depends on each job as every job is unique. Bricklayers generally look at each task individually and charges based on the complexity of each. We’ve put together this guide to give you an idea of the costs charged by bricklayers. Let’s have a look!

Generally, bricklayers charge either based on a daily rate or a fixed price for a particular amount of bricks ( usually a thousand bricks or 10 - 12 metres square). On the average, an experienced bricklayer can charge within a range of £150 to £200 daily rate and if a labour is needed for the job, an additional £60 to £100 may be included to get the job completed in a quick and fast manner. If the quoting is done based on the number of bricks to be incorporated, then a thousand bricks will be quoted in between £350 to £450 which should be completed in a couple of days.

You should however take note that most times, the bricklayer’s cost will depend on the amount of work involved in the project. As a result, a more tedious and challenging project will most definitely cost more than a simpler one. Examples of some difficult projects that’s likely to cost more are hard to reach areas, difficult sites as well as second storeys which are considered to be more challenging than single storey buildings. What’s more? The complexity of the project is also a great cost factor. While some projects are basically direct and straightforward, others involve curves and more complex designs which will ultimately make the cost jump up.

Asides the questions relating to planning permission of a loft conversion as well as the total cost of completing a loft conversion project, this is perhaps the most common question on the loft conversion subject matter. Before making an investment decision, many homeowners will want to know just how disruptive a loft conversion is. Well, we’ve all heard the several horror stories when loft conversion builder with dirty boots tramples all over the fresh and just-acquired shag pile or the noise of the construction loud enough to annoy neighbours from four blocks away or an obvious shortage of teabags, sugar and lots more. Good news is, the disruption of loft conversion is not as bad as people make out. Let’s have a look at how it works!

Just like all other major building projects, a loft conversion is disruptive to your property. However, no two loft conversions are the same, therefore some are certain to be more drastic and invasive than others. In the long run, the project is worth the stress and inconveniences caused and in most cases, it’s usually a very good investment.

Normally, an average loft conversion is expected to last for about 9 to 12 weeks (depending on the complexity of the loft conversion project some might take longer). Some of the factors that affects the duration of a project includes the type of the loft, the design of the loft as well as the style of the property.

Generally, a loft conversion is a lot less disruptive than say completely moving a home. It all has to do with how you’re able to deal with it as a person. And besides, the effect it’s going to have to a large extent depends on the company you hire. A good company will always look to ensure to keep disruptions to a minimal when carrying out the loft conversion project.

Cement is a crucial element in bricklaying that’s widely used in both construction as well as finishing works. Generally, they’re used to aerate concrete blocks, connect bricks, prepare plaster, floor levelling as well as the making of precast products. The major reason cement is one of the most common construction materials as its incredible ability to hold structure together. To get a cement plaster, you’d simply have to mix cement with both water and sand. However, when you mix cement with lime, sand and water, you’ll get a mortar.

For cements mortars to be used inside joints, you’ll have to include 1 part cement at the minimum to not more than 2 parts sand by weight which should be dry mixed and moistened with enough water to allow for troweling and packing without falling apart. Generally, the cement sand ratio in a mortar is in between 1:2 to 1:6. The cement and sand mix ratio is largely based on the importance of the project.

Cement provides a plethora of uses in bricklaying and these includes:

• Preparation of cement concrete

• Preparation of cement mortar

• Building fireproof and thermal proof structures

• Building chemical proof structures

• Serving as a grout material

• Building hydrographic and frost resistant structures

• Manufacturing precast members

• Constructing aesthetic concrete

• Constructing cement concrete roads

There are several types of cements with each having its specific purpose. For instance, the type of cement more suited to building a fire proof structure is a high alumnia cement and to build a hydrographic structure, cements like expanding cement, hydrophobic cement, pozzolana cement and quick setting cement are the best bet. Acid resistant cements are more useful in building chemical proof structures, portland cements are best suited to making grout materials, while coloured cements are preferable to building aesthetic structures.

You may need planning permission if you are planning a larger extension. All extensions will need building regulations approval. An architect can assist with this and if planning permission is required. A reputable contractor will also be able to advise you if this is needed as well.

How To Plasterboard A Wall

If you’re looking to plasterboard your wall, one of the essential things to have in mind is that the plasterboard must be hung horizontally and not vertically. Due to the way they’re manufactured, plasterboard sheets normally possess a “grain along the length. This implies that, it’s only when they’re firmly placed perpendicular against the wall that they’re able to achieve their maximum strength. Materials you’ll need to complete this task includes: Tape measure, stanley knife, pencil, spirit level, drill driver or screw gun, surform, drywall screws and handsaw. Now let’s have a look at the wall plasterboarding steps!

• To plasterboard a wall the first step to take is to place each board in such a way to make the edges the centre of the noggins and upright. Also, the the adjoining walls and door openings should fit closely to the edges.

• Work from the door opening to the ending wall. From the the stud’s edge to the noggin’s centre, use your tape measure to measure a cut board and as a rule to mark up.

• Place your spirit level on the marks and use the Stanley knife to run a line along the intended cut. Once done, turn the board on its edge and give a sharp push on the back to split.

• Cut the paper left with the knife after folding the split edge back on itself. This way, you should get a nice and clean edge.

• In its right position, place the board up against the studwork. Install the screws on the board’s edges where a noggin or upright can be seen.

• Mark lines down across the board at the stud’s centre.

• Cut the end boards to length.

• Install the remaining boards as mentioned above. While doing this, make sure the factory edges are together.

• Cut any board extending into an opening and finish the edges using a surform.

We’d recommend you hire the professional services of a plasterer for the best results especially if you lack the necessary training or experience. Plasterboarding a wall can be a tricky challenge and you’d save yourself some time, money and effort by getting it right on the first trial.

One of the main reasons why fitted wardrobes are a popular choice amongst homeowners is due to the fact that they’re able to help maximise storage space and since they’re usually customized for the particular room, they’re always good looking. However, just like any other home item, over time your installed wardrobe may start to look a bit dated and old fashioned. In these type of events and in order to save money, several homeowners would prefer to update its look to a more modern one without having to completely replace the fitted wardrobe with a new one. In this guide, we’ll give some great tips on how to update your old fitted wardrobe. Let’s take a look!

✓ Add mirrors to the wardrobe doors. Your old fitted wardrobe may be made of old fashioned laminate or chipboard which happens to draw scratches and dents here and there. If this is the case, you can simply add mirrors to help conceal the damage or unsightly marks.

✓ Include decorative trimming or panelling. You can choose from the various styles of trimmings you’ll find at hardware stores. By adding some strips of moulding, the whole look of your fitted wardrobe can change significantly.

✓ Painting. If the surface of the wardrobe permits, painting can go a long way to alter the look of the wardrobe.

✓ Change the handles. Handles may seem as a little item that doesn’t add to the aesthetics of the wardrobe. However, in reality, change your old handle with a more modern and fashionable one can make a great difference to the wardrobe’s overall appearance.

✓ Upgrade the interior. You can upgrade the interior of your wardrobe to give you more options and a better appearance. For instance, you may wish to have part of the wardrobe to offer integrated shelving or perhaps pull out drawers rather than having all the interior space for hanging clothes and garments.

How Much Do Roof Rooms Cost?

The price of your roof room may vary depending on your location within the country. Other factors that can also play a key role in determining the price of a roof room includes the conversion’s type as well as the legal and technical issues it’s currently facing. Usually, the cost of roof rooms will range between £1,200 to £2,000 per square metre. The differences in the price per square metre is influenced by the size of the alterations to the roof, the type of roof room to be constructed, the access, location as well as the finishing type.

• DORMER LOFT CONVERSION.

Here, one of the slopes of a pitched roof is substituted for a box-shaped structure. The outcome is a flat roof space which enables the fitting of full sized windows as well as the incorporation of several appliances. This is quite expensive as it involves a total rebuilding of one roof pitch alongside the complete internal works that are associated. The average cost of a standard dormer loft project will range between £25,000 to £50,000.

• HIP TO GABLE LOFT CONVERSION

Here a vertical brick wall is used to substitute the roof’s slope at the ending part of the terrace on detached buildings. The average cost of this type of roof room will range between £32,000 to £60,000.

• ROOFLIGHT LOFT CONVERSION

This basically involves fitting rooflight windows in the roof. Other improvements include flooring, plasterboarding, strengthening of the existing floor, as well as installation of rooflights. The average cost of this type of roof room will range between £15,000 to £25,000.

• MANSARD LOFT EXTENSION

This roof room can create an extra storey on top of an existing building as it makes a space featuring two or four external walls that are a bit sloped. The average cost of this type of roof room will range between £40,000 to £70,000.

External wall insulation works to keep your home cosy and comfy while also helping to cut the energy bills. However with the great benefits also comes great costs, so it’s actually a logical decision to know whether there are grants out there which you’re eligible for to help you handle the cost of the external wall insulation.

There are grants available for external wall insulation, but rarely will you find one that covers the full installation cost. With the help of the government’s Energy Company Obligation (ECO) scheme, a couple of energy companies assist in making your home more energy efficient by offering grants or free insulation. In certain cases whereby you receive particular state benefits, you may as well qualify for a higher grant that’ll cover more of the insulation cost.

However, if your energy supplier doesn’t offer any grant, you need not worry as you can save as much on energy bill after installation. Here’s what insulation can help you save per year on energy bills:

• Floor insulation can help you save within a range of £30 to £75 each year.

• Cavity wall insulation can help you save about £85 to £280 a year.

• Loft Insulation (270mm) can help you save about £135 to £250 a year.

Generally, the amount you’ll be able to save on your energy bills depends mainly on the type and size of your property, as well as how energy efficient it already is without the insulation. In the long run, your external wall insulation will more than give you back your investment on the valuable project through your savings on energy bills. In other words, whether or not you’re eligible for a grant should never stop you from installing an external wall insulation.