Find a Builder you can trust in Egremont.

Render serves two basic functions. One is it’s protective qualities as render acts as waterproof for the wall which enables them breathe by allowing water vapour move from the inside to the outside of the structure while also working to prevent water or rain from finding its way inside the structure. While the second function is the decorative qualities as render is able to provide the structure with a fine finish and colour to make the building a lot more appealing and correcting faults in line and level in the masonry.

If you wish to apply render on your external wall, you’d probably be wondering just how thick the render should be to perfectly serve both of functions. In this article, we’re going to take a look at just that!

For a render thickness, the British Standard Wind Driven Rain Index has come up with 4 ratings which include Sheltered, Moderate, Severe as well as Very Severe. An area with Very Severe rating include South West England. This rating implies that the thickness of the render in this area should be increased to at least 20mm for a direct one coat render applications as well as 5 to 6 external wall insulation base coat applications. And if you happen to reside within one mile of the coast, it’s strongly recommended you incorporate an extra repellent protection like Paraguard AG from Parex.

In general, render that’s prepared on site with cement and sand should be have a minimum of 20mm to 25mm thickness. Although, it should be noted that the quality of the render is based on quality of the sand incorporated, the design mix as well as being largely dependent on how good the mixing technique from the applicator is. The most common reasons why traditional renders fails is due to both poor mixing ratios and low quality materials used.

Are you about to start a new construction job when it’s a heavily rainy period? Or perhaps you’re just interested in knowing how bricklayers work. Well regardless of your purpose, one thing you should know is laying of bricks has a few rules and one of them is not to lay a brick wall when its raining. This is mainly because your structure’s quality and integrity would be heavily compromised if water comes in contact with the mortar before it gets the time to dry. However, with the help of a concrete protective tent, you can prevent water from coming in contact and damaging the mortar. So let’s look at the procedures to follow to work in the rain!

lDetermine The Concrete Protective Tents Required

• Concrete protective tents come in various sizes so you have to know what’s required to get the job done.

• Firstly, calculate the amount of space required to lay the brick wall

• Then, incorporate the appropriate size and number of tents.

lSet Up The Tents

• Follow the manufacturer’s instruction to set up the tents

• Once installed, the tent should extend past the location for the bricklaying and slope downwards.

l Access The Area

• Inspect the location during rainfall to ensure water is not sneaking through.

lBuild a Lumber Frame

• Use 2 to 4 pieces of lumber to build a frame.

• Set it into the ground depending on the size of your wall

lApply Concrete or Mortar

• Fill up the frame with either concrete or mortar.

• Follow the manufacturer’s instruction to allow the mixture to cure.

lPrepare the Brick Wall’s Mortar

• Mix the mortar for the brick wall construction

• Follow the manufacturer’s instruction for the process.

When you’re done laying the bricks, you can remove the protective tents once you’re certain the rain has stopped. Exposure to sun and air will speed up the curing process, which is quite important to protect the integrity of your structure.

External cladding will have an impact on a damp problem. However, it’s important that cladding is the last part of a damp treatment, as installing cladding over a damp wall will make the problem worse. Do not cut corners or try to remedy a problem with the cheapest solution, a damp proof course may need to be put in place before cladding.

Do you want to inject a new lease of life into your home or property, or transform it into a more modern style that better suits your taste? Or perhaps you’re only looking to add more value to your property to enable you sell for a profit in the nearest future. Regardless of your purpose, determining the cost of your home renovation can be incredibly difficult. However, you can still obtain a reasonable budget for the project with proper planning as well as preparation. It’s almost impossible to get an exact figure for any home renovation cost, however, this article aims to give you a good idea of cost range to enable you make informed decisions.

The cost of renovating a house can vary significantly depending on a wide range of factors. Some costs are fixed while others may vary greatly. As a result, if you want to have a more exact figure, you’ll have to call in a professional beforehand to give you an idea of how much they’ll charge. Below are some of the most significant costs you’ll most likely face during property renovation.

✓ Administrative cost. Asides from material and labour, the administrative costs is another important cost you’ll need to factor in. The first thing here is usually insurance, this is because all regular building insurance policies does not cover large scale renovation projects. So if what you’re planning is a huge structural change to your property, then it’s more likely that it won’t be covered by your buildings insurance policy. In this event, you’ll have to take out a specialist renovation insurance.

✓ Planning permission and property renovation. This is another potential cost you’ll have to factor in. Submitting a planning application in the UK usually ranges between £200 to £250.

✓ Adding an extension. Generally, a 4m by 5m extension would cost within the range of £30,000 to £40,000.

Typically, loft conversions do not require planning permission except in certain situations. They’re usually covered under what’s known as Permitted Development. Certain building works like loft conversion, rear extension and conservatories are granted planning permission by local authorities. Permitted Development, however, gives you a free range to improve your home without having any issues from the councils or regulations. Before your planned loft conversion can be covered under Permitted Development, there are some certain criteria that must be met. This criteria includes the following:

✓ The extension must not go beyond the existing slope of the roof at the front of the house.

✓ The loft space converted must not go beyond 40 cubic metres in a terraced house.

✓ The roof’s height must not be increased by the extension.

✓ The loft space converted must not reach beyond 50 cubic metres in a detached or semi detached house.

✓ The plan for the extension mustn’t involve structures like balconies, verandas or anything other structures of this nature.

✓ The roof extension should be positioned as far back as possible or at least 20cm from the existing eaves.

✓ The side that faces the window openings should be at least 1.7m beyond the floor and the windows should also be obscured.

✓ The roof extension must not overhang the existing roof or wall of the house.

✓ The materials that are to be used must be similar or the same to the materials that has already been used on the house’s exterior.

However, you should bear in mind that there are some properties that are exempt from Permitted Development. Examples of these type of properties include conservation areas, Areas Of Outstanding Natural Beauty and World Heritage sites. Permitted Development does not also provide coverage for listed buildings.

After making the decision to refurbish your home or property, the next obvious step is finding the right builder to get the job done. The process of getting a good and reliable builder can be a very tricky one especially when you don’t plan ahead. And in truth, the outcome of your house refurbishment project can only be as good as the contractor your hire. Consequently, finding the perfect builder for your task should be a top priority to get the best return on investment. Here are a few sources that will put you in the right direction to finding a reliable home refurbishment company.

✓ Friends, Relatives & Neighbours

If you have a friend, relative or neighbour that have recently completed a home refurbishment project, you can go for a visit to check out the work done. If you’re pleased with the work, you can proceed to ask about the work ethics of the builder and get the contact if satisfied.

✓ Internet

With the rapid rise of online technology, there’s hardly a service you can’t find on the internet. Websites like HomeAdvisor have been helping people find their desired service providers with relative ease for so long. To get the right building contractor online, it’s advisable to check reviews as well as testimonials before moving forward. Nowadays, you’re most likely going to find so many positive online reviews as some businesses now go to the extent of dubiously writing good reviews for their companies. As a result, it’s recommended to pay closer attention to the negative reviews and check if it’s something you can cope with before hiring a contractor.

✓ Store Contact Lists

You’ll discover a long list of building contractors on several stores trading building materials. These builders may not be affiliated with the store owners, but many stores see it as their responsibility to point you in the right direction so that the building materials acquired from them can be put to good use.

Sand is a very important element in bricklaying as far as a mortar mix is concerned. Generally, the quality of the sand is the major factor determining the quality of a plaster mix or mortar mix. It’s recommended that the sand should have enough ‘fines’ (- 75 micron material) to get a good plastic mix with a water content that’s less than 350 litres/m3. Generally, a mortar mix or plaster mix is made within the range of one bag of cement to 200 to 300 litres of damp sand.

Apart from experience the next best indicator of the quality of sand is a field test. In other words, if you do not have the required training or experience in bricklaying, the best bet to determine the amount of sand for a good quality mix is by carrying out a field test. Let’s have a look!

• Get about 50kg of sand and air dry it.

• Scoop 25kg of the sand, 5 kg of cement as well as litres of water ( with 1 litre and 1.5 litres of the water in different containers).

• Mix the cement and sand to form a smooth, uniform and consistent colour.

• One after the other, mix the the sand - cement mixture in the three quantities of water. Do this until you’re able to achieve a mix that’s workable enough to use as plaster.

With that done, you should take note that if 5 litres of water is sufficient then the quality and quantity of the sand is perfect. If you’d require 6 litres of water to get a mix workable as a plaster, then both the quality and quantity of the sand is average. However, if you’d need 7 litres of water to get a mix workable as a plaster, then the quality of the sand is poor. Any requirement of water above 7 litres implies a very poor quality of sand.

Rendering is an external wall’s plastered finish which provides a smooth finish while also protecting the brickwork from the elements like rain, snow and the likes. The traditional rendering is normally applied in two or three coats which enables it to be more resistant to surface cracks. In modern times, the finishes are largely different from the grey pebble dash of post war housing. Today, we now have a plethora of specialist products to pick from such as through-coloured silicone renders as well as one coat renders. The types of renders include the following:

✓ Cement renders. These are the common option that are usually mixed on site and used in a number of applications, then painted when dried. There’s a need to paint this type of render regularly to keep them looking great.

✓ Polymer renders. These are pre mixed and mostly pre coloured (usually with through colouring).

✓ Through-coloured products. These rendered do not need to be painted as the pigment is already added in the manufacturing process to colour the whole render.

✓ Lime renders. These are superior to cement as they’re less likely to trap moisture in the brickwork and also more good looking. However, they’re generally more costly and more difficult to apply.

Overall, rendering on a house provides several benefits. Not only is it able to protect your brickwork against the elements like the rain and wind, but it can also make the building more efficient. Being fully aware that about 30 percent of the energy used in heating a home is lost via the external walls, making use of a product such as acrylic insulated render is a smart approach to improve your home’s energy efficiency without affecting your interior living space.